SMC Networks ITV Series User manual

ITV2-TF2Z363EN
Page 1 of 2
Instruction Manual
Electro-Pneumatic Regulator
16 point Preset input type
ITV*0*0-5****** Series
The intended use of the electro-pneumatic regulator is tocontrol the flow
and pressure of fluid in response to preset input signals.
1 Safety Instructions
These safety instructions are intended to prevent hazardous situations
and/or equipment damage. These instructions indicate the level of
potential hazard with the labels of “Caution,” “Warning” or “Danger.”
They are all important notes for safety and must be followed in addition
to International Standards (ISO/IEC)*1), and other safety regulations.
*1) ISO 4414: Pneumatic fluid power - General rules relating to systems.
ISO 4413: Hydraulic fluid power - General rules relating to systems.
IEC 60204-1: Safety of machinery - Electrical equipment of machines.
(Part 1: General requirements)
ISO 10218-1: Robots and robotic devices - Safety requirements for
industrial robots - Part 1: Robots.
Refer to product catalogue, Operation Manual and Handling
Precautions for SMC Products for additional information.
Keep this manual in a safe place for future reference.
Caution
Caution indicates a hazard with a low level of risk which, if
not avoided, could result in minor or moderate injury.
Warning
Warning indicates a hazard with a medium level of risk
which, if not avoided, could result in death or serious injury.
Danger
Danger indicates a hazard with a high level of risk which, if
not avoided, will result in death or serious injury.
Warning
Always ensure compliance with relevant safety laws and
standards.
All work must be carried out in a safe manner by a qualified person in
compliance with applicable national regulations.
This product is class A equipment intended for use in an industrial
environment. There may be potential difficulties in ensuring
electromagnetic compatibility in other environments due to conducted
or radiated disturbances.
Caution
Ensure that the air supply system is filtered to 5 microns.
Refer to the SMC website (URL: https//www.smcworld.com) for more
information about Safety Instructions.
2 Specifications
2.1 General specifications
Model
ITV*010
ITV*030
ITV*050
Min. supply
pressure
(Set pressure) + 0.1 MPa
Max. supply
pressure
0.2 MPa
1.0 MPa
Set pressure range
0.005 to
0.1 MPa
0.005 to
0.5 MPa
0.005 to
0.9 MPa
Supply voltage
24 VDC ± 10%,
Current
consumption
0.12 A or less
Input signal
16 points (no common polarity)
Input impedance
Approx. 4.7 kΩ
Output signal
NPN –Open collector: 30 V 80 mA
PNP –Open collector: 80 mA
Linearity
±1% F.S. or less
Hysteresis
0.5% F.S. or less
Repeatability
±0.5% F.S. or less
Sensitivity
0.2% F.S. or less
Temperature
characteristics
±0.12% F.S. / °C or less
Ambient and fluid
temperature
0 to 50°C (no condensation)
Pressure
display
Accuracy
±3% F.S
Min. unit
MPa: 0.001 / kgf/cm2: 0.01 / bar: 0.01,
psi: 0.1 Note 1) / kPa: 1
Enclosure rating
Main unit: IP65, Cable connector: IP67
Note 1) 1 PSI is the minimum display unit on the ITV*050.
2.2 Size / Weight specifications
Model
ITV10*0
ITV20*0
ITV30*0
Size (mm)
50×50×109
50×50×131
66×66×152
Weight (no options)
250 g
350 g
645 g
Warning
Special products (-X) might have specifications different from those
shown in this section. Contact SMC for specific drawings.
3 Installation
3.1 Installation Warning
Do not install the product unless the safety instructions have been read
and understood.
This product is pre-set at the factory and must not be dismantled by
the user. Contact your local SMC office for advice.
Ensure, when installing this product, that it is kept clear of power lines
to avoid noise interference.
Ensure that load surge protection is fitted when inductive loads are
present (i.e. solenoid, relay etc.).
3.2 Environment Warning
Do not use in an environment where corrosive gases, chemicals, salt
water or steam are present.
Do not use in an explosive atmosphere.
Do not expose to direct sunlight. Use a suitable protective cover.
Do not install in a location subject to vibration or impact. Check the
product specifications.
Do not mount in a location exposed to radiant heat.
3 Installation (continued)
3.3 Piping Caution
Before piping make sure to clean up chips, cutting oil, dust etc.
When installing piping or fittings, ensure sealant material does not
enter inside the port. When using seal tape, leave 1 thread exposed
on the end of the pipe/fitting.
Tighten fittings to the specified tightening torque.
3.4 Lubrication Caution
Do not use a lubricator on the input side of this product. If lubrication
is required, place the lubricator on the ‘output’ side so that it does not
enter the product.
SMC products have been lubricated for life at manufacture, and do not
require lubrication in service.
If a lubricant is to be used in the system, refer to the catalogue for
details.
4 Wiring
Caution
Connect the cable to the connector on the main unit as shown in the
following diagram. Take precautions, as incorrect wiring will damage the
unit. Use a DC power supply capable of supplying the necessary power
requirements with minimal ripple.
4.1 Power supply connector
Item
Pin assignment
Wire colour
Connector for
power supply
1. +24V
Brown
2. F.G.
White
3. GND
Blue
4. N.C.
-
4.2 Signal connector
Item
Pin assignment
Wire colour
Connector for
input signal
1. Input 0 bit (S0)
Brown
2. Input 1 bit (S1)
White
3. Input 2 bit (S2)
Blue
4. Input 3 bit (S3)
Black
5. Input common
Grey
Note: Wire colours shown are when the optional cable is used.
5 Settings
Caution
Turn OFF the power supply before setting the switches.
When the ‘SET’ key is operated the minimum / maximum pressure will
be present at the outlet port. When primary pressure is applied to the
regulator minimum pressure will be present at the outlet port.
5.1 Setting Procedure
Release ‘Key Lock ’as explained in section ‘Key-Lock Function’
After releasing key lock, press the ‘Set’ key again to move to F-1
To set the minimum pressure (display shows F-1) use up/down keys
and press the ‘Set’ key to ‘Lock’ the setting.
To set the maximum pressure (display shows F-2) use up/down keys
and press the ‘Set’ key to ‘Lock’ the setting.
Note 1: If the above sequence has been followed correctly, the settings
will complete automatically.
Note 2: If only setting minimum pressure, when pressure is ‘Set’,
pressing the set button once more will ‘skip’ to the next step.
5.2 Key-Lock function
The keys will be locked and cannot be operated when the power is
supplied. ‘Loc’ is displayed when any keys are pushed.
Key-Lock Release
Press the ‘Down’ key for 2 seconds or more.
Display will flash ‘Loc’ (locked).
Press the ‘Set’ key to unlock.
Note: To cancel press the ‘Up’ key.
Key-Lock
Press the ‘Up’ key for 2 seconds or more.
Display will flash ‘unL’ (unlocked).
Press the ‘Set’ key to lock.
Note: To cancel press the ‘Down’ key.
5.3 Error Display
If an abnormality is detected by the ITV the LED display will show ‘Er’
followed by a code number. Isolate the power supply and ascertain the
problem and solve. Re-instate the power supply after correcting any fault.
Error codes are as shown in the table below.
No
Content
Display
2
EEProm read / write error
Er 2
3
Memory read / write error
Er 3
4
Solenoid valve fault
Er 4
5
Switch output over-current
Er 5
6
Outside of the Zero-clear range
Er 6
5.4 Reset function
Press the ‘Up’ and ‘Down’ keys together for 3 seconds or more.
Display shows ‘RES’.
Release keys to reset minimum pressure and maximum pressure.
5.5 Zero-clear function
Press the ‘Set’ keys together for 2 seconds or more.
Press the ‘Up’ and ‘Down’ keys. Display shows ‘F03’.
Press the ‘Set’ keys. Display shows ‘OcL’(Flashing).
Press the ‘Up’ and ‘Down’ keys together. Display shows ‘Ocl’.
Press the ‘Up’ and ‘Down’ keys together for 3 seconds or more. Display
shows ‘clr’ (1second).
Zero-clear is complete.
5.6 Initialization
Press the ‘Set’ key together for 2 seconds or more.
Press the ‘Up’ and ‘Down’ keys. Display shows ‘F99’.
Press the ‘Set’ keys. Display shows ‘ini’ (flashing).
Press the ‘Up’ and ‘Down’ keys together. Display shows ‘ini’.
Press the ‘Up’ and ‘Down’ keys together for 5 seconds or more. Display
Turns OFF (1 second).
Initialization is complete.
ORIGINAL INSTRUCTIONS
3
1
2
1
2
3
4
1
4
2
3
5
Vs: Power
Supply
24 VDC
(no polarity)
Grey

ITV2-TF2Z363EN
Page 2 of 2
6 Input state for Preset pressures
Preset
pressure
S3
S2
S1
S0
P01
OFF
OFF
OFF
OFF
P02
OFF
OFF
OFF
ON
P03
OFF
OFF
ON
OFF
P04
OFF
OFF
ON
ON
P05
OFF
ON
OFF
OFF
P06
OFF
ON
OFF
ON
P07
OFF
ON
ON
OFF
P08
OFF
ON
ON
ON
P09
ON
OFF
OFF
OFF
P10
ON
OFF
OFF
ON
P11
ON
OFF
ON
OFF
P12
ON
OFF
ON
ON
P13
ON
ON
OFF
OFF
P14
ON
ON
OFF
ON
P15
ON
ON
ON
OFF
P16
ON
ON
ON
ON
7 How to Order
Refer to the operation manual or catalogue on the SMC website (URL:
http// www.smcworld.com) for How to order information.
8 Outline Dimensions
Refer to the operation manual or catalogue on the SMC website (URL:
http// www.smcworld.com) for outline dimensions.
9 Maintenance
9.1 General maintenance Caution
Not following proper maintenance procedures could cause the product
to malfunction and lead to equipment damage.
If handled improperly, compressed air can be dangerous.
Maintenance of pneumatic systems should be performed only by
qualified personnel.
Before performing maintenance, turn off the power supply and be sure
to cut off the supply pressure. Confirm that the air is released to
atmosphere.
After installation and maintenance, apply operating pressure and
power to the equipment and perform appropriate functional and
leakage tests to make sure the equipment is installed correctly.
If any electricalconnections are disturbed duringmaintenance, ensure
they are reconnected correctly and safety checks are carried out as
required to ensure continued compliance with applicable national
regulations.
Do not make any modification to the product.
Do not disassemble the product, unless required by installation or
maintenance instructions.
Ensure all air is exhausted from the product before maintenance.
10 Limitations of Use
10.1 Limited warranty and disclaimer/compliance requirements
Refer to Handling Precautions for SMC Products.
11 Product Disposal
This product shall not be disposed of as municipal waste. Check your
local regulations and guidelines to dispose of this product correctly, in
order to reduce the impact on human health and the environment.
12 Contacts
Refer to www.smcworld.com or www.smc.eu for your local
distributor/importer.
URL : https:// www.smcworld.com (Global) https:// www.smc.eu (Europe)
SMC Corporation, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, Japan
Specifications are subject to change without prior notice from the manufacturer.
© 2021 SMC Corporation All Rights Reserved.
Template DKP50047-F-085M