fantastic furniture COMO Single Bed User manual

Assembly Instructions
Single Bed
COMO
VER 1.2

Page 3
What You Need
To Assemble The Body
(Tools not provided)
Flat Blade Screwdriver
Phillips Head Screwdriver
Mallet
28 x Small
Dowels
(H2)
10 x Small
Cam Nuts
(H9)
10 x Small
Cam Bolts
(H8)
Please make sure you have all these parts before you start.
11 x Plastic
Glides
(H13)
4 x Elbow
Connectors
(H11)
4 x Flat
Connectors
(H12)
12 x Bolts
(H10)
Left Drawer
Side (P8)
Drawer Front
(P7)
x 2
Right
Drawer
Side
(P9)
Drawer Back
(P10)
Drawer
Base
(P11)
Central
Drawer
Support
(P12)
2 x Drawer
Supports
(P13)
2 x Cam Bolts
(H3)
2 x Cam Nuts
(H4)
Bedhead
(P1)
Bedfoot
(P2)
Side Rail
(P3)
Side Rail
(P3)
Rail
(P4)
Rail
(P4)
Base
Panel
(P5)
Block
(P14)
Block
(P14)
Block
(P14)
Block
(P14)
Clapboard
(P6)
8 x Wheels
(H15)
1 x Allen Key
(H16)
3 x Stickers
(H7)
26 x Plastic Connectors
4 x Elbow
Brackets
(H1)
26 x Screws
(Ø4 x 25)
(H5)
32 x Small
Screws
(Ø3.5 x 12)
(H14)
30 x Screws
(Ø4 x 30)
(H6)
13 x Fantastic Furniture
ComfortSlats Single
TM

H8
H8
H9 H9
H9
H9
H9
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
5 x Small
Dowels
(H2)
Page 4
Step 1
You will need:
5 x Small Cam
Bolts
(H8)
Step 3
You will need:
(P7)
(P13)
(P7)
(P8)
(P12)
(P13)
(P13)
(P9)
Insert 5 x Small Dowels (H2) into Drawer Front (P7), and attach 5 x Small Cam Bolts (H8) to it.
Attach 2 x Wheels (H15) to Drawer Support (P13) with 4 x Small Screws (H14).
Repeat Step 2 again with the other Drawer Support (P13).
5 x Small Cam
Nuts
(H9)
Insert 5 x Small Cam Nuts (H9) into the holes of Drawer Sides (P8,P9)
and Central Drawer Support (P12).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Sides (P8,P9) and Central Drawer Support (P12) into place
and tighten the cam nuts.
Attach 2 x Drawer Supports (P13) to Drawer Front (P7).
Step 2
You will need:
H8
H15
H14
H15
H14
H8
H8
H2
H2
H2
4 x Wheels
(H15)
8 x Small
Screws
(H14)
(P8) (P9)
Grooves should
face inside.

Page 5
Step 4
Step 6
(P11)
Slide Drawer Base (P11) into the groove in the Drawer Sides (P8,P9).
Insert 4 x Small Dowels (H2) into Drawer Support (P13).
Step 5
You will need:
6 x Screws
(H6)
Repeat step 1 to step 5 to assemble the other drawer.
Attach Drawer Back (P10) to Drawer Sides (P8,P9) with 4 x Screws (H6),
and Central Drawer Support (P12) with 2 x Screws (H6).
Make sure that the groove lines up the whole way around the drawer.
4 x Small
Dowels
(H2)
You will need:
H2 H2
H2 H2
(P10)
(P9)
(P8)
(P8)
(P9)
H6
H6
H6
H6
H6H6

Page 6
Step 7
You will need:
2 x Cam Bolts
(H3)
Attach 1 x Cam Bolt (H3) to Side Rail (P3).
Attach 2 x Elbow Connectors (H11) to Side Rail (P3) with 8 x Screws (H5).
Repeat Step 7 again with the other Side Rail (P3).
16 x Screws
(H5)
4 x
Elbow
Connectors
(H11)
3 x Plastic
Glides
(H13)
H3
H5 H5
H14
H14
H14
Step 8
You will need:
Attach 4 x Elbow Brackets (H1) to Base Panel (P5) with 8 x Small Screws (H14).
Then hammer 3 x Plastic Glides (H13) on the bottom of Base Panel (P5).
4 x Elbow
Brackets
(H1)
8 x Small
Screws
(H14)
H14
H14
H1
H5
H5
H5
H5
H11
H11
H13
H1
H1
H1
H1
H13
H13
Raw Edge
(P3)
(P5)

Page 7
Step 9
You will need:
8 x Screws
(H6)
3 x Plastic
Glides
(H13)
2 x Flat
Connetors
(H12)
Attach 2 x Flat Connectors (H12) to Bedhead (P1) with 8 x Screws (H6).
Then hammer 3 x Plastic Glides (H13) on the bottom of Bedhead (P1).
Attach 2 x Flat Connectors (H12) to Bedfoot (P2) with 8 x Screws (H6).
Then hammer 3 x Plastic Glides (H13) on the bottom of Bedfoot (P2).
Step 10
You will need:
8 x Screws
(H6)
3 x Plastic
Glides
(H13)
2 x Flat
Connetors
(H12)
(P2)
(P1)
H6 H6
H13
H13
H13
H6 H6
H12
H12
H6 H6
H13
H13
H13
H12
H12
H6 H6

2 x Cam Nuts
(H4)
You will need:
Step 11
2 x Small
Dowels
(H2)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Page 8
Step 12
You will need:
H13
P4 MUST GO IN
CORRECT WAY WITH
HOLE CLOSE TO TOP
H13
2 x Screws
(H6)
Attach Rails (P4) to Clapboard (P6) with 2 x Screws (H6).
Then hammer 2 x Plastic Glides (H13) on the bottom of Clapboard (P6).
(P4)
(P4)
(P6)
WRONG
H6
H6
2 x Plastic
Glides
(H13)
(P6)
Insert 2 x Small Dowels (H2) into Side Rails (P3).
Insert 2 x Cam Nuts (H4) into the holes of Clapboard (P6).
Rotate the cam nuts so the arrow point towards the incoming cam bolts.
Push Side Rails (P3) into place and tighten the cam nuts.
(P3)
(P3)
H2
H4
10mm
RIGHT
10mm
MAKE SURE
TWO ENDS ALIGN

Page 9
(P3)
(P3)
(P2)
(P6)
You will need:
6 x Bolts
(H10)
Step 13
4 x Small
Dowels
(H2)
4 x Small
Dowels
(H2)
H2
H10
Insert 4 x Small Dowels (H2) into the holes of Bedfoot (P2).
Attach Side Rails (P3) to Bedfoot (P2) with 6 x Bolts (H10) using Allen Key (H16).
(P3)
(P3)
(P1)
Step 14
You will need:
6 x Bolts
(H10)
1 x Allen Key
(H16)
Insert 4 x Small Dowels (H2) into the holes of Bedhead (P1).
Attach Side Rails (P3) to Bedhead (P1) with 6 x Bolts (H10) using Allen Key (H16).
1 x Allen Key
(H16)
2 PEOPLE CAREFULLY
TURN OVER THE BED FRAME
H2
H2
H10
H16
H16

4 x Screws
(H5)
(P6)
(P1)
(P1)
(P2)
(P2)
(P14)
(P14)
(P4)
H5
H5
H5
H5 H5
H5
H5
Page 10
You will need:
Step 15
4 x Screws
(H5)
You will need:
Step 16
Attach 2 x Blocks (P14) to Rail (P4) with 4 x Screws (H5).
Attach 2 x Blocks (P14) to Rail (P4) with 4 x Screws (H5).
(P6)
(P14)
(P14)
(P4)
H5
H5
H5
H5H5
H5 H5