SMITH SYSTEM 58000 User manual

Assembly Instructions
MOTUM TEACHERS DESK
FIXED HEIGHT RIGHT HAND
If you have damaged or missing components,
please contact customer service at 1-800-328-1061
MODEL NUMBERS
58000, 58002, 58004, AND 58006
REVISED: 2/2022
Document #: 179716

REVISED: 11/2020
For 72” Models Only (58004 and 58006)
Document #: 179716
ITEM NO. DESCRIPTION QTY
1 TEACHER DESK U TUBE LEG ASSEMBLY 1
2 SWIVEL GLIDE W/ GLIDE STOP 2
3 TEACHER DESK STRAIGHT TUBE LEG ASSEMBLY 1
4 TD BRACED L BRACKET 1
5 TD STRAIGHT TUBE LEG Z BRACKET 1
6 TD BOLT ON L BRACKET 1
7 TD SIDE PANEL CLIP 2
ITEM NO. DESCRIPTION QTY
8 TD U TUBE LEG Z BRACKET 1
9 TD L BRACKET FRONT 120 1
10 TD FILLER BRACKET 2
11 TD L BRACKET FRONT MAIN 1
12 TD FRONT MAIN TO 120 SPACER 1
13 TEACHER DESK HARDWARE PACK 1
14 TD FIXED HEIGHT SHIM 4
ITEM NO. DESCRIPTION QTY
15 TEACHERS DESK TD SUPPORT BRACE 1
16 TEACHERS DESK SUPPORT BRACE HARDWARE PACK 1
Hardware and Components

Hardware and Components
REVISED: 2/2022
Document #: 179716
ITEM NO. DESCRIPTION QTY
13-1 NO. 10 X 5/8" TORX BUTTON HEAD SCREW 70
13-2 NO. 10 X 1/2" TORX SELF DRILLING BUTTON HEAD SCREW 2
13-3 10-32 X 1/2" TORX BUTTON HEAD W/PATCH 8
13-4 T25 TORX POWER BIT #2 1
USED ON
58002 and 58006
USED ON
58000 and 58004

BOX B ITEM #B-11 (60140) –
TD SPLIT HEIGHT HARDWARE
PACK COMPONENTS
ITEM NO. DESCRIPTION QTY
13-1 NO. 10 X 5/8" TORX BUTTON HEAD SCREW 70
13-2 NO. 10 X 1/2" TORX SELF DRILLING BUTTON HEAD SCREW 2
13-3 10-32 X 1/2" TORX BUTTON HEAD W/PATCH 8
13-4 T25 TORX POWER BIT #2 1
ITEM NO. DESCRIPTION QTY
11-1 NO. 10 X 5/8" TORX BUTTON HEAD SCREW 44
11-2 NO. 10 X 1/2" TORX SELF DRILLING BUTTON HEAD SCREW 1
11-3 10-32 X 1/2" TORX BUTTON HEAD SCREW W/PATCH 7
11-4 M6 X 1.0 X 20MM SOCKET HEAD, HEX DRIVE, BLK OX 3
11-5 M6 X 1.0 X 10MM SOCKET HEAD, HEX DRIVE, BLK OX 4
11-6 1/4" I.D. PLASTIC LOOP CLAMP 2
11-7 HEX KEY 5MM SHORT ARM 1
11-8 T25 TORX POWER BIT 2" 1
11-9 10-32 X 1" TORX BUTTON HEAD W/PATCH 4
11-10 #10 WASHER 1" od 8
11-11 M6 SPLIT LOCK WASHER 4
REVISED: 2/2022
Document #: 179716
Hardware and Components

Document #: 179716 REVISED: 11/2020
FOR 60” MODELS ONLY
58000 AND 58002
FOR 72” MODELS ONLY
58004 AND 58006
Hardware and Components
PANEL LETTER DESCRIPTION QTY
A TD STRAIGHT LEG PANEL 70
B TD U LEG SIDE PANEL 2
F TD MAIN FRONT PANEL RH 8
GTD 120 FRONT PANEL RH 1

REVISED: 2/2022
Document #: 179716
General Assembly Guidelines
Special Notes:
•Ensure that all components are accounted for and undamaged
before assembling
•Follow each step carefully to ensure the proper assembly of this
product
•2-person assembly is highly recommended
•Clean the product with a mild cleaner and damp cloth
Tools:
•Framing Square
•Drill
•#1 and #2 Phillips bit
•Screwdriver (optional)
•Wood Clamps (optional)
•¼” bit extender (optional)

Document #: 179716 REVISED: 11/2021
1. Place wood top on clean smooth surface upside down with the pilot holes facing up,
fasten 2x item #7 to item A using 4x fasteners item #1 using the supplied T25 Torx bit
item # 4.
2. Position Panel B as shown, centering the panel to create equal gaps, a spacer or
credit card works well. Fasten panel #7 to item A using 4x fasteners item #1 using the
supplied T25 Torx bit item # 4. NOTE: The panel should sit on the metal finger as
shown.
Assembly Instructions

Reference line
Reference line
Vertical Tubes
Document #: 179716 REVISED: 11/2021
REFERENCE LINES PILOT HOLES
3. Place wood top on clean smooth surface upside down with the pilot holes and reference
lines facing up. The reference lines will be used to help align the metal components in
future steps, these are only guides final locations will vary by assembly accuracy. (Panel I is
used in these instruction, substitute panel I with panel E for 60” models)
Assembly Instructions
4. THE POSITION OF COMPONENT 3 IS CRTITICAL, IT DETERMINES ALL OTHER COMPONENTS
POSTIONS AND IS THE MOST DIFFICULT TO CHANGE AFTER THE ASSEMBLY IS DONE. The
outside edge of item #3 vertical tubes should sit flush with the 3 indicated reference lines
below.
5. Fasten item #3 down with 2x fasteners item #1 using the two pilot holes, confirm the location is
correct as described above and install the remaining 6x fasteners item #1.

Document #: 179716 REVISED: 11/2021
5. Slide the previously assembled panel A onto item #3, item #7 should side over the
metal lip of item #3 as shown. Do not install any fasteners at this point this board will be
removed later. It it helpful to clamp panel A to item #3.
6. Install items #5 and #4 to item #3 as shown using 4x fastener item #3, finger tighten
only. (Right hand assembly shown)
Assembly Instructions

Reference line
Flush with #11’s edge These faces
should be flush
Document #: 179716 REVISED: 11/2021
7. Align item #11’s edge
with the reference line
as shown. Item #11
should be touching Item
#3 and the faces
indicated below should
be flush. Fasten #11 to
top using 4x fastener #1.
Install these two
fasteners first
Edges of panel F and A should
be flush as shown, a faming
square is recommended.
Edges of panel F and A should be flush as shown, a framing
square is recommended. Confirm at the top and bottom
edges are flush
8. Using 2x item #10 as spacers. Place panel F as shown.
Confirm panel F and A edges align as show. Fasten panel F
with the 2x indicated fastener #1 first, confirm panel F and
A edges are still aligned and install the remaining 6x #1
fasteners
Assembly Instructions

Document #: 179716 REVISED: 11/2021
10. Place item #12 as shown. Confirm panel F and item #12 faces align as show. Fasten
item #12 with the 5x fasteners #1.
9. Align item #10’s edge with the reference line as shown. Item #10 should be
touching Item #11. Fasten #10 to top using 2x fastener #1.
Reference line
Flush with #10’s edge
These faces of item #10 and
#11 should touch
Edges of panel F and item #12
should be flush as shown, check
top and bottom before fastening,
a straight edge is recommended.
Assembly Instructions

Edges of panel G and item #1 should
be parallel, the gap should be as
minimal as possible, check top and
bottom before fully fastening.
Assembly Instructions
Document #: 179716 REVISED: 11/2021
12. Place the previously assembled item #1 and panel B as shown. Attach item #8 using 2x fastener
#1 to panel G and attached item #8 to item #1 using 2x fastener #3, finger tighten only. Confirm
the gap between item #1 and panel G is constant and as minimal as possible as shown below.
Fully tighten fasteners.
11. Align item #9’s edge with the reference line as shown. Item #10 can be used as a spacer for panel
G. Insert panel G into the slot of Item #12. Place item #9 against panel G as show. Confirm that all
3x holes on item #12 and item #9 can be seen though the slots while item #10 is in place. Fasten
#12 and #9 to panel G using 3x fastener #1 each. (Do not fasten item #9 to the panel I, this will be
done in further steps)
Reference line
Flush with #9’s edge

Assembly Instructions
Document #: 179716 REVISED: 11/2021
14-A. This step is for 58000 and 58004 only, all other models skip to step 14-B.
Remove all components from inside 19179 before inverting. Remove panel A assembly
and set to the side. Position 19179 the metal flanges should touch the metal components
as shown below, install 8x fastener #1 on the two side flanges as shown.
Reference Line / Parallel edge
No fasteners on
this back tab
These edges
will touch
13. Edge of item #1 should be parallel with the reference line as shown (depending on the assembly
process the reference line may not be flush with the edge of item #1) Align edge of tube from item #1
with the edge of the wood, NOT the face of the edge banding. Fasten #1 to panel I using 8x fastener #1
and then faster item #9 to panel I using 3x fastener #1.
Align edge of tube from item #1 with the edge of the
wood(brown surface), NOT the face of the edge banding.

Assembly Instructions
Document #: 179716 REVISED: 11/2021
15. Place item #6 as shown, Fasten #6 to the tube of item #3 using 2x fastener #3, finger tighten only.
Install 2x fastener #2. (Fastener #2 is a self drilling fastener, it will create 2 new holes in item 19179)
Confirm there is a constant gap between 19179/19178 and the tube of item #3. Tighten the 2x
fastener #2.
14-B. This step is for 58003 and 58007 only.
Remove all components from inside 19178 before inverting. Remove panel A assembly and set to the
side. Position 19178 front face is flush with the edge of wood as shown below, allow for a small gap
between the tube of item #3 and hinge. (door is shown removed for illustrative purposes), install 6x
fastener #1 in the 6x holes of 19178 as shown.
Line up face
this this edge
Allow for a small
gap between hinge
and this tube

Assembly Instructions
Document #: 179716 REVISED: 11/2021
17. Place item #14 between the bottom of 19179/19178 and the casters that came with 19179/19178.
Install the 16x fasteners that came with 19179/19178.
16. Replace panel A, item #10 can be used as a spacer. Confirm that panel A and F are
flush, a framing square is recommended. Install 3x fastener #1 into panel A

Assembly Instructions
Document #: 179716 REVISED: 11/2021
18-B. This step is for 60” Models only (58000 and 58002).
The indicated face of item #10 should be flush with item #1 as shown. Install 2x fasteners #1 into
panel E.
18-A. This step is 72” Models only (58004 and 58006), for all other models skip to step 18-B.
Line up item #15 with the reference line. Install 8x fasteners from hardware pack supplied
with item #15 into panel I.
Reference line
These faces
should be flush

Assembly Instructions
Document #: 179716 REVISED: 11/2021
20. Flip desk onto casters as shown.
19. Unlock all casters, on a soft, clean surface flip the desk on its front face as shown.
Reference line