Softing echocollect Installation and user guide

© Copyright 2014 Softing Industrial Automation GmbH
Configuring a Softing echocollect to establish data
exchange between a Siemens S7-300 and an
Allen-Bradley ControlLogix
echocollect
How to...
Version: E-032014-01

The information contained in these instructions corresponds to the technical status at the time of printing of it and is
passed on with the best of our knowledge. The information in these instructions is in no event a basis for warranty
claims or contractual agreements concerning the described products, and may especiallynot be deemed as warranty
concerning the qualityand durabilitypursuant to Sec. 443 German Civil Code. We reserve the right to make any
alterations or improvements to these instructions without prior notice. The actual design of products may deviate from
the information contained in the instructions if technical alterations and product improvements so require.
It may not, in part or in its entirety, be reproduced, copied, or transferred into electronic media.
Disclaimer of liability
Softing Industrial Automation GmbH
Richard-Reitzner-Allee 6
85540 Haar / Germany
Tel: + 49 89 4 56 56-0
Fax: + 49 89 4 56 56-488
Internet: http://industrial.softing.com
Email: [e-mail]
Support: [e-mail]
The latest version of this manual is available in the Softing download area at: http://industrial.softing.com.

Table of Contents
echocollect - How to... 3
Table of Contents
Chapter 1 ..................................................................................5
Introduction
Chapter 2 ..................................................................................6
NetCon echo – echocollect port network
settings
Chapter 3 ..................................................................................7
Create a connection to the S7-300 PLC
Chapter 4 ..................................................................................9
Create a connection to the ControlLogix
PLC
Chapter 5
..................................................................................12
Create the table to establish data transfer
from "Data_to_S7" (CLX) to "DB1"
(S7-300)
Chapter 6
..................................................................................16
Create the table to establish data transfer
from "DB2" (S7-300) to "Data_from_S7"
(CLX)
Chapter 7 ..................................................................................20
Finished table mapping

This page is intentionally left blank.

Chapter 1 - Introduction
echocollect - How to... 5
1 Introduction
This document provides step by step instructions on how to establish data exchange
between a Siemens S7-300 PLC and an Allen-Bradley ControlLogix PLC, using a Softing
echocollect device.
General description of the presented example
Both PLCs and the echocollect are in the same network.
No program changes required on the PLCs. All the configuration is done on the
echocollect.
The data source tag on the ControlLogix is an array of 50 integers called Data_to_S7.
The target data block on the S7-300 is DB1, defined also as an array of 50 integers.
The data recipient tag on the ControlLogix is an integer called Data_from_S7.
The source data block on the S7-300 is DB2, defined as one byte.
Software used
Softing NetCon echo V4.33
Conventions
The following conventions are used throughout Softing customer documentation:
Keys, buttons, menu items, commands and
other elements involving user interaction are
set in bold font and menu sequences are
separated by an arrow
Open Start Control Panel
Programs
Buttons from the user interface are enclosed
in brackets and set to bold typeface
Press [Start] to start the application
Coding samples, file extracts and screen
output is set in Courier font type
MaxDlsapAddressSupported=23
Filenames and directories are written in italic
Device description files are located in C:
\StarterKit\delivery\software\Device
Description files
Note
This symbol is used to call attention to notable information that should be
followed during installation, use, or servicing of this device.

Chapter 2 - NetCon echo – echocollect port network settings
6echocollect - How to...
2 NetCon echo – echocollect port network settings
1. Start NetCon echo and configure the network settings of the echocollect port to be
used. We will use port 1 (Eth 1).
a. Click on Station Own Station 1.
b. As a minimum, the IP address and subnet mask are required. DNS and Router
addresses may be necessary in some cases.

Chapter 3 - Create a connection to the S7-300 PLC
echocollect - How to... 7
3 Create a connection to the S7-300 PLC
1. Click on Connection New Connection.
2. Enter a connection name.
3. Click on Logic Table Connection and select the PLC/Raw and Ethernet options.

Chapter 3 - Create a connection to the S7-300 PLC
8echocollect - How to...
4. After clicking [OK], select the TCP/IP and Siemens S7 options.
5. Enter the IP address of the S7-300 and click [OK].
6. Click [OK] again.

Chapter 4 - Create a connection to the ControlLogix PLC
echocollect - How to... 9
4 Create a connection to the ControlLogix PLC
1. Click on Connection New Connection.
2. Enter a connection name.
3. Click on Logic Table Connection and select the PLC/Raw and Ethernet options.

Chapter 4 - Create a connection to the ControlLogix PLC
10 echocollect - How to...
4. After clicking [OK], select the TCP/IP and Rockwell CompactLogix / ControlLogix
options.
5. Enter the IP address of the ControlLogix PLC and then click on [Protocol Settings].
6. Enter the CPU slot number (2 in our example) and click [OK].