Solas SEVENTY2 LGS-72 User manual

0
INSTALLATION MANUAL
ONLY FOR USE ON SÓLAS MODELS: 72N-SSL, 72P-SSR, 72N-ST, 72P-SSL, 72P-SSR, 72P-ST
SEVENTY2
DIRECT VENT LOG SET KIT
PART
#:
LGS
-
72
WARNING
This log set kit shall be installed by a qualified service agency in accordance with
the manufacturer’s instructions and all a licable codes and requirements of the
Authority Having Jurisdiction. If the information in these instructions is not
followed exactly, a fire, ex losion or roduction of carbon monoxide may result
causing ro erty damage, ersonal injury or loss of life. The qualified service
agency is res onsible for the ro er installation of this kit. The installation is not
ro er and com lete until the o eration of the converted a liance is checked as
s ecified in the manufacturer’s instructions su lied with the kit.
NOT FOR USE WITH VENT FREE OR OUTDOOR FIREPLACES

1
LOG SET INSTALLATION
Kit Contents:
•(5) Ceramic Logs
•(6) Ceramic Rocks
•2lb 0oz Lava Rock
•Metal Logset burner set
Figure 01 - Burner Support locations
Step #1
Your fire lace will have shi ed from the factory with the Glass Media burners in lace, before
installing the logset burners, we need to remove the glass burners. The left and right burners are each
held in lace by 6 sheet metal screws, and a central link which ties the 2 burners together. Each burner
su ort is secured by 2 sheet metal screws, each burner has 3 burner su orts (see figure 01). In all, to
remove both burners, you will be removing 14 sheet metal screws. Begin by removing the central burner
link, which secures both burners to each other, identified by the large arrow in figure 03.
Step #2
To remove the left burner, begin by removing the burner link identified by the large arrow below.
Once the central burner link has been removed, remove the 6 sheet metal screws securing the left
burner, these screws are identified by the 6 smaller arrows below. Once all hardware has been removed,
slide the burner to the left and lift the burner out of the fire lace.
Figure 02 Figure 03

2
LOG SET INSTALLATION
Step #3
To remove the right burner, remove the 6 sheet metal screws securing the right burner, these
screws are identified by the 6 arrows below. Once all hardware has been removed, slide the burner to
the right and lift the burner out of the fire lace.
Figure 04 Figure 05
Step #5
Once the glass media burner has been removed, locate the Logset burner included in the kit LGS-72 and
install in the fire lace reusing the hardware removed during disassembly.
NOTE:
The logset burner can be configured for either Natural Gas or Pro ane by installing or removing
a collar on the burner venturi. Figure 06 shows the venturi inlet with the collar installed on a burner
configured for Natural Gas. Figure 07 shows the venturi inlet with the collar removed from a burner
configured for Pro ane. TH S VENTUR S NOT ADJUSTABLE. If you need to convert your burner
from Pro ane to Natural Gas or vice-versa, lease order the a ro riate conversion kit for your
a liance.
Configured for Natural Gas
Configured for Propane
FIGURE 7
FIGURE 6

3
LOG SET INSTALLATION
Step #8
Install the 3-rock cluster on the 2 ins located at the far left of
the firebox as shown in figure 8.
Step #9
Install the right-hand birch log by lacing the
left side of the log on the 3-rock cluster
installed in ste #10. A groove on the underside
of the log which engages with the leading edge
of the burner. The right side of the log will rest
against the right enamel anel within the
firebox. (Figure 9)
Step #10
Install the single rock on the 2 ins located on
the far left of the burner to . The log-locating
tab on to of the rock should be toward the
back of the burner. (Figure 10)
FIGURE 11
FIGURE 12
FIGURE 13

4
LOG SET INSTALLATION
Step #13
Between the rock installed during ste #12 and
the center birch log are 4 ins located in close
roximity to each other. Place the first of the 2
individual rocks on the left set of ins. Look for
a ga between the front of the rock and the
leading edge of the burner, if the rock
overhangs the front of the burner the incorrect
rock has been used. (Figure 14)
Step #14
Place the second of the 2 individual rocks on the
right set of ins as shown in figure 15. The
second rock should overhang the back of the
burner. The second rock will overhang the rear
of the burner, nearly contacting the rear enamel
anel.
Step #15
Between the rock installed during ste #12 and
the air of rocks installed during ste s #13 and
#14, are 2 ins. The “Y” sha ed log has 2 holes
on its underside that corres ond with these 2
ins. The right side of the log will rest on the air
of logs as shown in figure 16.
FIGURE 14
FIGURE 1
5
FIGURE 1
6

5
LOG SET INSTALLATION
Step #16
Evenly distribute the included 1lb and 3oz of
lava rock on the ex osed burner to . Cover the
burner to com letely but do not com ress or
“ ack” the lava rock tightly. Pay s ecial
attention to tight and hard to reach areas when
lacing the media on the burner. It is ok if small
amounts of lava rock are lost over the edge of
the burner. (Figures 17 & 18)
Step #17
Using the log-locating tab on the single rock on
the left side of the burner, rest the small birch
log on the rock and “Y” sha ed log while
aligning it with the leading edge of the burner as
shown in figure 19.
FIGURE 17
FIGURE 1
9
FIGURE 18

6
LOG SET INSTALLATION
nstallation is now complete, refer to the FORTY6 owner’s manual for instructions on final
assembly and lighting of the appliance.