Solas SIXTY0 LGS-60 User manual

0
INSTALLATION MANUAL
ONLY FOR USE ON SÓLAS MODELS: 60N-SSL, 60P-SSR, 60N-ST, 60P-SSL, 60P-SSR, 60P-ST
SIXTY0
DIRECT VENT LOG SET KIT
PART #: LGS-60
WARNING
This log set kit shall be installed by a qualified service agency in accordance with
the manufacturer’s instructions and all a licable codes and requirements of the
Authority Having Jurisdiction. If the information in these instructions is not
followed exactly, a fire, ex losion or roduction of carbon monoxide may result
causing ro erty damage, ersonal injury or loss of life. The qualified service
agency is res onsible for the ro er installation of this kit. The installation is not
ro er and com lete until the o eration of the converted a liance is checked as
s ecified in the manufacturer’s instructions su lied with the kit.
NOT FOR USE WITH VENT FREE OR OUTDOOR FIREPLACES

1
LOG SET INSTALLATION
Kit Contents:
•(5) Ceramic Logs
•(6) Ceramic Rocks
•1lb 11oz Lava Rock
•Metal Logset burner set
Figure 01 - Burner Support locations
Step #1
Your fire lace will have shi ed from the factory with the Glass Media burners in lace, before
installing the logset burners, we need to remove the glass burners. The left and right burners are each
held in lace by 4 sheet metal screws, and a central link which ties the 2 burners together. Each burner
su ort is secured by 2 sheet metal screws, each burner has 2 burner su orts (see figure 01). In all, to
remove both burners, you will be removing 10 sheet metal screws. Begin by removing the central burner
link, which secures both burners to each other, identified by the large arrow in figure 02 below.
Step #2
To remove the left burner, begin by removing the burner link identified by the large arrow in
Figure 02. Once the central burner link has been removed, remove the 4 sheet metal screws securing the
left burner, these screws are identified by the 4 smaller arrows below. Once all hardware has been
removed, slide the burner to the left and lift the burner out of the fire lace. Remove the left burner by
sliding the burner to the left then lifting u into the room.
Figure 02

2
LOG SET INSTALLATION
Step #3
To remove the right burner, remove the 4 sheet metal screws securing the right burner, these
screws are identified by the 4 arrows below. Once all hardware has been removed, slide the burner to
the right and lift the burner out of the fire lace. Remove the burner by sliding the assembly to the right,
then lifting u into the room.
Figure 03
Step #5
Once the glass media burner has been removed, locate the Logset burner included in the kit LGS-60 and
install in the fire lace reusing the hardware removed during disassembly.
NOTE:
The logset burner can be configured for either Natural Gas or Pro ane by installing or removing
a collar on the burner venturi. Figure 06 shows the venturi inlet with the collar installed on a burner
configured for Natural Gas. Figure 07 shows the venturi inlet with the collar removed from a burner
configured for Pro ane. THIS ENTURI IS NOT ADJUSTABLE. If you need to convert your burner
from Pro ane to Natural Gas or vice-versa, lease order the a ro riate conversion kit for your
a liance.
Configured for Natural Gas
Configured
for Propane
IGURE 0
5
IGURE 0
4

3
LOG SET INSTALLATION
Step #6
Install the left logset burner within the firebox by lowering the burner into the firebox. (while
kee ing the burner ressed toward the left side of the firebox) then sliding the burner right towards the
center of the firebox to engage the burner orifice. Confirm that the burner inlet tube has engaged the
burner orifice. Secure the burner using the (6) sheet metal screws set aside from ste s 1-3.
Figure 06 – Step #6-A
Figure 07 – Step #6-B
Figure 08 – Step #6-C

4
LOG SET INSTALLATION
Step #7
Install the right logset burner within the firebox by lowering the burner into the firebox. (while
kee ing the burner ressed toward the right side of the firebox) then sliding the burner left towards the
center of the firebox to engage the burner orifice. Confirm that the burner inlet tube has engaged the
burner orifice. Secure the burner using the (6) sheet metal screws set aside from ste s 1-3.
Figure 09 – Step #7-A
Figure 10 – Step #7-B
Figure 11 – Step #7-C