SOMFY Sunis WireFree II io User manual

Manual
Sunis WireFree™ II io

2
Description 3
Program the sensor on the motor with a 1-way transmitter 4
Program the sensor on a Connexoon io 4
Program the sensor on a TaHoma 4
Operating mode 5
“Standard” operating mode 5
“My” operating mode 5
Switch from “Standard” to “My” operating mode 6
Switch from “My” to “Standard” operating mode 6
Compatibility with autonomous actuators 6
Activate the Low Power Mode 6
Deactivate the Low Power Mode 6
Demo mode 7
Activate the demo mode 7
Deactivate the demo mode 7
Set the threshold in a 1-way installation 8
Check the threshold 8
Change the threshold 8
Set the threshold on a Connexoon io 9
Use 10
1-way installation 10
2-way installation 11
Sunis WireFree II io sensor Contents

3
Sunis WireFree II io sensor
Sunis WireFree II io sensor
Description
Wall bracket
Green LED (prog ) Orange LED (Threshold 5 → 8)
Orange LED (Batteries) Green LED (Threshold 1 → 4)
PROG-button Threshold

4
Sunis WireFree II io sensor
Sunis WireFree II io sensor
Program the sensor on a motor with a 1-way transmitter
Program the sensor on a Connexoon io
The Connexoon io must not be connected with internet for this handling
Program the sensor on a TaHoma
Press on the PROG button of a
Smoove A/M io or of a
Situo 5 VAR A/M io until...
Press briefly the PROG button of the Sunis
WireFree II io sensor, until...
Press 2 s on the PROG button of the
Sunis WireFree II io sensor until the
green LED lights up
...short movement
OK
...short movement
OK
3 s
3 s
Back of a Smoove Back of a Situo
Press 2 s on the
PROG button of the Connexoon.
The LED blinks and
becomes green
Follow the instruction on the interface of the TaHoma.
2s

5
Sunis WireFree II io sensor
Sunis WireFree II io sensor
Operating mode
1 Standard operating mode
Send the Maestria+ 50 io motors to the down end-limit when sun is detected
2 My operating mode
Rolling
shutters
Rolling
shutters with
tilting slats
External
screen Internal screen Awning
Ext. venetian
blind
Sun
My Down end limit My
No sun
Upper end limit Flat slats
Rolling
shutters
Rolling
shutters with
tilting slats
External
screen Internal screen Awning
Ext. venetian
blind
Sun
My
No sun
Upper end limit

6
Sunis WireFree II io sensor
Sunis WireFree II io sensor
3 Switch from “standard” modus to “My” operating mode
A new sensor is always delivered in “Standard” mode
4 Switch from the “My” to the “standard” mode
A new sensor is always delivered in “Standard” mode
Compatibility with autonomous actuators
1 Activate the Low Power mode
To switch the mode press
5s on the “+” button until…
To switch the mode press
5s on the “+” button until…
To activate the LP mode press
2 s on the “+” AND on the “-“
button until…
To deactivate the LP mode
press 5s on the “+” AND on
the “-“ button until…
...the LEDs are blinking.
The “My” mode is activated
...the LEDs light up.
The “standard” mode is
activated.
…the orange LED light up.
The LP mode is activated
… the green LED light up.
The LP mode is deactivated
>5s
>5s
>2s
>5s
2 Deactivate the Low Power mode

7
Sunis WireFree II io sensor
Sunis WireFree II io sensor
Demo mode
1 Activate the demo mode
nThe demo is automatically deactivated aer 3 minutes.
nAn order will be send 30 s aer the threshold is exceed.
nNever change the threshold in demo mode.
to activate the DEMO mode
press 5s on the
“-“ button until…
To deactivate the DEMO mode
press 5 s on the “-“ button
until…
...the orange and green
LED are blinking.
The DEMOmode is activated
for 3 min.
...the orange and green
LED light up.
The DEMO mode is
deactivated.
>5s
>5s
2 Deactivate the DEMO mode

8
Sunis WireFree II io sensor
Sunis WireFree II io sensor
Set the threshold in a 1-way installation
1 Check the threshold
2 Change the threshold
3 Threshold
Press briefly on the “+” of “-“
button to check the threshold
Press briefly on the “+” or “-“
button to check the
actual value
Press briefly within 2 s on the
“+” or “-“ button to raise or
lower the threshold
2s
or
or or
Feedback
1 = 10 kLux
2 = 16 kLux
3 = 24 kLux
4 = 32 kLux (default value)
5 = 40 kLux
6 = 50 kLux
7 = 65 kLux
8 = 80 kLux
Sunis WireFree II io sensor

9
Sunis WireFree II io sensor
Sunis WireFree II io sensor
Set the threshold on a Connexoon io
The threshold is set on the interface.
You can create up to 4 scenarios per sensor.
Create a scenario
Press on the pictogram
Name the scenario
Choose between 2 settings: > “more than” or < “less than”
Set the threshold by sliding the cursor
Optional you can set an activation periode
Set the days when the sun function may be activated
Select the applications you want to control. You have also the possibility to
send an alert.
Choose a new scenario or to
modify an existing scenario
Confirm the new settings with the OK-button

10
nWhen the threshold is exceed
nWhen the measured value still exceed the threshold, each 30 minutes an order is send.
nWhen the measured value falls below the threshold
Sunis WireFree II io sensor
Use in a 1-way installation
Remark: We don’t need anymore a sensorbox for the correct working of the Sunis WireFree II io sensor.
1 Activate the sun function
of
of
2 Deactivate the sun function
3 Delay time
Smoove A/M io
Smoove A/M io
Situo 5 Variation
A/M io
Situo 5 Variation
A/M io
Slide the Auto/Manu switch to Auto...
Slide the Auto/Manu switch to Manu...
...short movement.
The sun function is activated.
...short movement.
The sun function is deactivated.




5 min
20 min
Sunis WireFree II io sensor