SOMFY Smoove UNO io User manual

11
Smoove Uno io
Smoove Uno io
Smoove Uno io
1 Connect the motor using an setting cable
2 Check the rotation direction
3 Change the rotation direction
4 Put the application in the middle
Put the application in the middle
RTS
WT
RTS
WT
OK 4

Not OK 3
Swap the black and the brown wires
RTS
WT
230V AC
RTS
WT
or
Determine the rotation direction (the motor must be set)
Smoove Uno io

ground wire
neutral wire
ground wire
neutral wire

22
Smoove Uno io
Smoove Uno io
Smoove Uno io
Smoove Uno io
Connect the motor on the control
Overview of the control
230V AC
Motor
LED
PROG
Down
Auto/Manu Stop/my
Up

33
Smoove Uno io
Smoove Uno io
Smoove Uno io
Smoove Uno io
Settings of the DIP switches
Backside of the
Smoove Uno io
Setting of the application on the Smoove Uno io
Rolling shutter
Factory setting
All OFF
Screens
No. 2 = ON
Roller blind
No. 3 = ON
External venetian blind
No. 1 - ON
Awning
No. 1 and
No. 2 = ON
Curtain
No. 1 and
No. 3 = ON
Window
No. 2 and
No. 3 = ON
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
ONOFF

44
Smoove Uno io
Smoove Uno io
Smoove Uno io
Smoove Uno io
Programming
Use the UP button to move the
application in the upper end limit
Press again briefly on the UP and
DOWN buttons, the application goes to
his down end limit
Press > 5 s simultaneous on the
UP and DOWN buttons till a short
movement of the application
When the down end limit is
reached, press immediately on
the MY (stop) button
Press the PROG
button until the LED
lights up green
Follow the instructions
on the screen
...short movement
of the application
Transmitters
without feedback
Transmitters with
feedback
1 Set the running time
(The end limits of the motor must be set upfront)
2 Program or delete the transmitter
This procedure can only be carried out within 30 s of the appliance being switched on or aer inserted
the electronic module into the Smoove Uno io
5 s
➞
➞
A
B
Briefly press the PROG button
until...
<1 s
<1 s
Back of the
Smoove
Back of the Situo
Nina io

55
Smoove Uno io
Smoove Uno io
Press and hold the
PROG button for more
than 7 s
Aer 2s, the LED
lights green up
permanently
Short up and down
movement
Aer a further 5s,
the LED flashes
3 Product back in the orginal configuration
(This procedure can only be carried out within 30 s of the appliance being switched on or aer inserted
the electronic module into the Smoove Uno io)
7 s
All configurations
and all saved io
equipments are
removed from his
memory
Position the product in the required position
Position the product in the MY position
Press short on the MY button
to stop the product
Press on the MY
button until...
Press again on the MY button
for at least 5 s till a short
movement
The My position
is saved
...a short up and down
movement of the product.
The MY position
is deleted
4a Save the MY position
4b Remove the MY position
5 s
5 s
OR
OR
OR

66
Smoove Uno io
Smoove Uno io
Press the DOWN button until the
down end limit is reached with the
slats closed to the exterior
5 Set the rotation angle for external venetian blinds
Press simultaneous
and at least 5 s on
the UP and DOWN
buttons
The blind performs
a short up and down
movement
Press the MY button, the blind performs
a short up and down movement
Press briefly but repeatedly on
the UP button to turn the slats
from the closed to fully open
position
Ones the maximum position
has been reached, press
simultaneous on the UP and MY
buttons until a short up and down
movement of the blind
>5 s
OR OR