SOMFY Sonesse Ultra 50 DC RS485 User manual

Sonesse ULTRA 50 DC RS485
Instructions
EN

3
Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved. Images non contractuelles
EN
CONTENTS
ORIGINAL GUIDE
1. PREREQUISITE INFORMATION
1.1 FIELDS OF APPLICATION
The Sonesse ULTRA 50 DC motor is designed to operate interior Roller blinds applications.
The Sonesse ULTRA 50 DC motor is designed to operate multiple roller blinds simultaneously (multi-
banding), where these are interconnected by an intermediate bracket.
The Sonesse ULTRA 50 DC motor is not designed to be used with a compensating spring.
Any use outside the fields of application is prohibited, in particular:
The Sonesse ULTRA 50 DC motor is not designed for outdoor applications (e.g. outdoor vertical blinds,
roller shutters, etc.)
The Sonesse ULTRA 50 DC RS485 motor has been developed for interior use.
Its ultra quiet operation ensures user comfort and well-being.
For more information, and to optimise the acoustic performance of your interior application, please
contact a Somfy adviser.
These instructions apply to all Sonesse ULTRA 50 DC RS485 irrespective of torque and speed variations.
1. Prerequisite information 3
1.1 Fields of application 3
1.2 Liability 4
2. Installation 4
2.1. Installation 4
2.2. Wiring 5
2.3. Commissioning 6
2.4. Tips and recommendations for installation 7
3. Use and maintenance 8
3.1. Operation 9
3.2. LED behavior 9
3.3. Tips and recommendations for use 9
4. Technical data 10
5. Power supply 10
6. Power panel 10

4Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved.Images non contractuelles
EN
1.2 LIABILITY
Before installing and using the motor, please read these instructions carefully. In addition to the
instructions given in this guide, please also comply with the instructions set out in the enclosed docu-
ment Safety instructions.
The motor must be installed by a home motorisation and automation professional, in accord-
ance with Somfy’s instructions and the applicable regulations in the country of installation.
Any operation of the drive outside the sphere of application described above is prohibited. Such opera-
tion shall exclude Somfy from all liability and invalidate the Somfy warranty, as will any failure to
comply with the instructions given herein and in the enclosed Safety instructions document.
Aer installing the drive, the installer must inform his customers of the operating and maintenance
conditions for the drive and must pass the operating and maintenance instructions on to them, as
well as the enclosed Safety instructions document. Any Aer-Sales Service operation on the drive
requires intervention by a home motorisation and automation professional.
Should any doubt arise during installation of the drive or for additional information, consult a Somfy
contact or visit www.somfy.com.
2. INSTALLATION
Instructions which must be followed by the motor and home automation professional installing
the motor.
Never drop, knock, drill or submerge the motor.
Install a separate control point for each motor.
To optimize ultra quiet operation, the mechanical plays between motor, accessories and tube
must be minimized.
2.1. INSTALLATION
2.1.1. Preparing the motor
Ensure that the inner diameter of the application tube greater
than 47mm.
1) Fit the accessories required to integrate the motor in the
roller tube:
• Install the crown a, the motor wheel band the stop wheel c
on the motor.
The stop wheel must be screwed with a torque ranging
between 1.5 and 1.8 Nm.
2) Measure the length (L1) between the inner edge of the
motor head and the edge of the motor wheel.
3) Screw the motor bracket adapter on the motor head.



Safety warning! Information
Caution!

1)
L1
L1 = …
2)
Ø > 47 mm
ba
c
3)

5
Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved. Images non contractuelles
EN
2.1.2. Tube preparation
1) Cut the roller tube to the required length, depending on the
motorised product.
2) Deburr the roller tube and remove the burrs.
2.1.3. Motor/tube assembly
1) Slide the motor into the roller tube.
2) The motor wheel must be locked in place to prevent
movement inside the roller tube:
• This can be done either by fixing the roller tube to the
motor wheel using 4 x Ø 5 mm self-tapping screws, or by
using 4 x Ø 4.8 mm steel pop rivets placed 5mm to 15mm
from the outer edge of the motor wheel, regardless of the
roller tube.
The screws or pop rivets must only be attached to the
motor wheel and not to the motor.
3) Slide the end cap into the roller tube and locked it if necessary.
2.1.4. Installing the motor/tube assembly
The motorised product must not be compressed between
the brackets
1) Install and fix the motor/tube assembly onto the end bracket
fand onto the motor bracket g:
Ensure that the motor/tube assembly is secured onto
the end bracket. This operation prevents the motor/tube
assembly from coming out of the end bracket mounting
when the roller blind reaches the lower end limit position.
2) Clip the stop ring hin place.
2.2. WIRING
Cables which pass through a metal wall must be protected and isolated using a grommet
or sleeve.
Attach cables to prevent any contact with moving parts.
Leave the motor power supply cable accessible: it must be possible to replace it easily.
-Switch off the power supply (compatible power supply, see page 10).
-Connect the cable to the motor head.
1)
2)
h
g
f


15 mm
5 mm
20 mm
L1
1)
2)
3)
1) 2)


V+
V-
+
-
G
V+
V-
+
-
G
Power Data

6Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved.Images non contractuelles
EN
UP STOP DWN
UP STOP DWN
21
2.3. COMMISSIONING
Switch on the power supply.
If the motor is not set, the Led stays ON.
If the motor is already set, the Led stays OFF.
WITH THE MOTOR HEAD BUTTONS
Press and hold the Up and Down buttons on the motor
head buttons at the same time until the motorised product
moves up and down, then release.
The motor is in commissioning mode.
2.3.1. Checking the direction of rotation
1) Press and hold the Up button on the motor head:
a) If the motorised product rises (a), the direction
of rotation is correct: Move onto the section entitled
“Setting the end limits”.
b) If the motorised product lowers (b), the direction of
rotation is incorrect: Move onto the next step.
2) Press and hold the Stop button on the motor head until
the motorised product moves up and down, then release:
The direction of rotation has been modified.
3) Press the Up button on the motor head to check the
direction of rotation.
2.3.2. Setting the end limits
The end limits can be set in any order.
Setting the lower end limit
1) Press and hold the Down button on motor head to
lower the motorised product to the lower end limit.
2) Release the button to stop the motorised product. If
necessary, adjust the down position, using the Up or Down
buttons.
3) Press the Up and Stop buttons at the same time until
the motorised product moves, and release.
The lower end limit is memorised.
Setting the Upper end limit
1) Press and hold the Up button on motor head to to raise
the motorised product to the upper end limit.
2) Release the button to stop the motorised product. If
necessary, adjust the down position, using the Up or Down
buttons.
3) Press and hold the Down and Stop buttons at the same
time until the motorised product moves.
The lower end limit is memorised.
a
b
=
=
UP STOP DWN UP STOP DWN
UP STOP DWN
a
b
=
=
UP STOP DWN UP STOP DWN
UP STOP DWN
a
b
=
=
UP STOP DWN UP STOP DWN
UP STOP DWN
1)
2) 3)
1) 2)
3)
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN
UP STOP DWN UP STOP DWN
1) 2)
3)
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN
UP STOP DWN UP STOP DWN

7
Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved. Images non contractuelles
EN
2.3.4. Validation of the setting
To confirm the end limits, press and hold the Stop button
until the motorised product moves up and down. The end
limits are programmed (the Led switches OFF).
WITH THE RS485 SETTING TOOL
Connect the RS485 SETTING TOOL to the motor, switch on and follow the instruction on the RS485
SETTING TOOL (Refer to page 12).
UP STOP DWN UP STOP DWN
UP STOP DWN UP STOP DWN
UP STOP DWN
UP STOP DWN UP STOP DWN
2.4. TIPS AND RECOMMENDATIONS FOR INSTALLATION
2.4.1. Questions about the Sonesse ULTRA 50 DC RS485?
Observations Possible causes Solutions
The motorised product
does not operate
The wiring is incorrect. Check the wiring and modify it if necessary.
The motor is in thermal protection.
LED flashing (3 short flashes) Wait until the motor cools down.
The control point is not
compatible. Check for compatibility and replace the control point if necessary.
The motorised
product is noisy
The motor wheel and the crown are
not suitable for the tube. Replace the motor wheel and the crown
The motorised product is compressed
between the brackets Increase the play between the brackets
The tube contains burrs and screws. Clean the roller tube.
During setting with
the RS485 SETTING
TOOL, the following
message error “Not
accepted by the
node” appears on the
screen
One step of the setting process was
not performed correctly
Restoring the original configuration (according
to: factory default...) then start again the
setting process from step 1 to X
The motorised product
stops too soon or too
late.
The end-limits of the motorised
product dri. Readjust the end-limits
1) 2)
3)
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
2.4.2. Readjusting the motor rotation direction
1) Move the motorised product away from an end limit.
2) Press and hold the Up and Down buttons at the
same time until the motorised product moves up and
down, then release.
3) Press and hold the Stop button on the motor head
until the motorised product moves up and down, then
release: The direction of rotation has been modified.

8Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved.Images non contractuelles
EN
2.4.3. Readjusting the end limits
Readjusting the upper end limit
1) Press and release the Up button to bring the
motorised product to the end limit to be readjusted.
2) Press and hold the Up and Down buttons at the same
time until the motorised product moves up and down,
then release.
3) Press the Up or Down buttons to move the motorised
product to the new desired position.
4) To confirm the new end limit, press and hold the Stop
button until the motorised product moves up and down,
and release.
Readjusting the lower end limit
1) Press and release the Down button to bring the
motorised product to the end limit to be readjusted.
2) Press and hold the Up and Down buttons at the same
time until the motorised product moves up and down,
then release.
3) Press the Up or Down button to move the motorised
product to the new desired position.
4) To confirm the new end limit, press and hold the Stop
button until the motorised product moves up and down,
then release.
2.4.4. Restoring the original configuration (Factory mode)
Press the Up, Stop and Down buttons at the same time
( ≈7s) until the motorised product moves up and down
once and the LED comes on.
The motor is now in Factory mode, and the led stays ON.
1) 2)
3)
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
4)
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
1) 2)
3)
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
4)
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
UP STOP DWN
3. USE AND MAINTENANCE
This motor is maintenance-free.
For the safety of goods and people, Somfy motors are equipped with thermal protection that will
trigger the motor stops in the event of overheating.
Repeated activation of this protection can degrade motor performance.
If the motor goes to thermal protection, please check your installation and check that the motor
is rated for the intended use.
A normal installation is not expected to trigger this protection.
No user serviceable parts.


9
Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved. Images non contractuelles
EN
3.1. OPERATION
To control the motorised product, please refer to the technical instructions of the dedicated controler.
The images of the control point are not contractually binding
3.2. LED BEHAVIOR
3.3. TIPS AND RECOMMENDATIONS FOR USE
Questions about the Sonesse ULTRA 50 DC RS485?
If the motorised product still does not work, contact a motorisation and home automation professional.
Observations Possible causes Solutions
The motorised product does not
operate. The motor is in thermal protection
mode. Wait for the motor to cool down.
The motorised product makes
a movement in the opposite
direction of the last order.
The motorised product detects an
obstacle.
LED flashing (2 short flashes)
Remove the obstacle.
Motor status LED behavior Comments
Power ON
2" ON and 1" OFF
During 2"
LED will come on briefly and shut off unless
motor is in factory mode
Obstacle detection 2 short flashes Till next movement
Thermal protection 3 short flashes Till thermal time expired
Digital message to/
from motor Long flashes ... During all communication, and stops when
communication is finished
Motor is not set Permanent ON LED stays on until motor is set with limits.

10 Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved.Images non contractuelles
EN
Manufacturer Model Ratings
GLOBTEK, INC GT-46402-4024 Input: 100 - 240 Vac, 50-60 Hz, 1.0 A
Output: 40W 24 VDC SELV, 1.67A ±5%
5. POWER SUPPLY
The Sonesse ULTRA 50 DC RS485 is only compatible with the following power supply:
4. TECHNICAL DATA
Working voltage 24V dc ±5%
Operating temperature 0°C to + 60°C
Index protection rating IP 20
Safety level Class III
Manufacturer Model Ratings
SOMFY Part number 1870259
and 1870270
Input: 120Vac, 60 Hz, 7.2 A
Output: 24 VDC, 2 A per motor output
6. POWER PANEL
The Sonesse ULTRA 50 DC RS485 is only compatible with the following power pannel:

11
Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved. Images non contractuelles
EN

12 Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved.Images non contractuelles
EN
EN **Select the preset position (1 to 16) with the
BACK
OPEN
STOP
CLOSE
OK LIGHT
buttons.
SOMFY RS485
NODE DISCOVERY
NODE ID : XXXXX
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
MOTOR 50DC RS485:
AP:0000000X0000
ST:0000000A0000
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT

13
Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved. Images non contractuelles
EN
MOTOR ROTATION:
(Standard/ Reversed)
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
UP LIMIT
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
DOWN LIMIT
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SET UP LIMIT
OK TO FINE TUNE
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
FINE TUNE LIMIT
SETTING:
SET DOWN LIMIT
OK TO FINE TUNE
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
FINE TUNE LIMIT
SETTING:
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SET STANDARD
OK TO CONFIRM
SET REVERSED
OK TO CONFIRM
UP SPEED
SETTING:
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
DOWN SPEED
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
UP SPEED
SETTING: XXX
DOWN SPEED
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SLOW SPEED
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SOFT START
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SLOW SPEED
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK
LIGHT
SOFT START
SETTING STD
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SOFT START
SETTING OFF
1
1
1
1
1
1
1

14 Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved.Images non contractuelles
EN
EN **Select the preset position (1 to 16) with the
BACK
OPEN
STOP
CLOSE
OK LIGHT
buttons.
SOMFY RS485
NODE DISCOVERY
NODE ID : XXXXX
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
MOTOR 50DC RS485:
AP:0000000X0000
ST:0000000A0000
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT

15
Copyright © 2016 - 2018 SOMFY ACTIVITÉS SA, Société Anonyme. All rights reserved. Images non contractuelles
EN
FACTORY DEFAULT
MOTOR RESET
PRESET POSITION
TESTING
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
PRESET POSITION
ERASING
BACK TO FACTORY?
OK TO CONFIRM
SET PRESET 01
OK TO FINE TUNE
**
PRESET POSITION
SETTING
PRESET : 01
XXX%
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
FINE TUNE PRE-
SET SETTING
BACK
OPEN
STOP
CLOSE
OK
LIGHT
TEST PRESET 01
OK TO CONFIRM
**
PRESET : 01
XXX%
PRESET : 01
XXX%
BACK
OPEN
STOP
CLOSE
OK
LIGHT
Product
movement
ERASE PRESET 01
OK TO CONFIRM
**
PRESET : 01
XXX%
PRESET : 01
XXX%
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
PRODUCT RESET
PRESS OK
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SOFT STOP
SETTING: XXX
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SOFT STOP
SETTING STD
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SOFT STOP
SETTING OFF
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
1
1
1
1
1
SET OVERTORQUE
PROTECTION
SET OVERTORQUE
PROTECTION ON
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT
SET OVERTORQUE
PROTECTION OFF
1
Product
movement
BACK
OPEN
STOP
CLOSE
OK
LIGHT
BACK
OPEN
STOP
CLOSE
OK LIGHT

SOMFY ACTIVITÉS SA
50 avenue du Nouveau Monde
F-74300 Cluses
www.somfy.com
5123104C
5123104C
SOMFY ACTIVITES SA, Société Anonyme, capital 35.000.000 Euros, RCS Annecy, 303.970.230 - 04/2018 Images not contractually binding