SOMFY tecnoShades NR0-Rn Installation manual

NR0-Rn, NR1-Rn, NR2-Rn
PROGRAMMING INSTRUCTIONS
WARNING
1. The installation and adjustment of the electric
motor must be carried out by qualified personnel,
using the device in the manner described.
2. This motor is not suitable for use by the following
people (including children): people with physical or
mental disabilities, sensory disabilities, or people
who lack experience and knowledge of the prod-
uct.
3. Do not use or stop using if the application
and/or the product is damaged, especially if it has
damage to the cable and covers. If the cord is
damaged, it must be replaced by the manufacturer,
its service agent or qualified personnel, in order to
avoid a hazard.
4. Do not operate the equipment during mainte-
nance programs.
5. When operating the electric motor, make sure
there are no people in the area before the shade
closes completely.
6. During installation, the horizontal distance of at
least 0.4 m must be maintained between the first
moving part anchored to the motor and the fixed
parts.
7. During the use and installation of the electric
motor, all cables must not touch the blind. Keep the
radio reception antenna in good condition. (Do not
cut or place the antenna around metal materials,
otherwise reception may be affected.)
8. The motor should be kept in a dry place; The
remote control battery should be replaced with a
new one once it runs out, otherwise it will affect the
transmission distance. Replace the battery as soon
as the control transmission distance is reduced.
9. When the electric motor is moving the app “up”,
it is forbidden to press the “down” button directly.
When the electric motor is moving the app “down”,
it is prohibited to press the “up” button directly. The
correct operation is to wait for the electric motor to
reach its limits and stop or press the "stop" button to
stop, then press the reverse rotation button to make
the motor reverse its direction of rotation.
10. Before performing any type of maintenance,
turn off the power supply to the motor and discontin-
ue use of the controls.
11. If you have any questions about the installation
and operation of the manufacturer's electric motor,
or accessories, visit www.tecnoshades.com for your
consultation.
12. The manufacturer declares that this product is in
compliance with the essential requirements and
other relevant regulations 1999/5/EC.
www.tecnoshades.com

INSTALLATION
www.tecnoshades.com
1. The electric motor must be installed in a dry and ventilated
environment.
2. Before installation, check that the moving parts have good
mechanical properties, balance properties, and good
opening and closing performance. Make sure the electricity
meets the product specifications.
3. Check whether the size and shape of the adapters (wheel
and crown) match the tube, and make sure all the
accessories are fixed, and do not cause any mechanical
hindrance to the motor.
4. After the motor is inserted into the tube, fix the wheel and
ring gear to the tube to ensure there is no relative movement
between the three components.
5. Install the electric motor and tube above the window or
door; Attach the mounting brackets to the wall on each side
with screws. Keep the electric motor and tube horizontal, and
the tube should be perpendicular to each side of the door or
window.
6. Installation diagram.
7. The outlet plug must be equipped and grounded.
Connection diagram:
8. The installation of the motor must be correct and reliable.
The shade should be able to move smoothly through its
gutters without hindrance.
1. Wall or panels
2. Bearing
3. Screw or rivet
4. Final shaft with wheel or cover
5. Drive wheel
6. Screw or rivet
7. Tubular motor
8. Crown
9. Motor head for wall
10. Star plate
11. Wall or panels
M
N
L
Blue
Brown
Yellow
Green
M
N
L
White
Black
Green
Connection diagram 120V ACConnection diagram 230V AC

PROGRAMMING
www.tecnoshades.com
CHANGING THE DIRECTION OF ROTATION
The following programming instructions must be carried out
step by step.
If the power supply was suspended or timed out before the
third step, you must start from the first step after restoring the
power supply.
Feedback = cycle: It is a short movement of the electric motor
up and down.
If the direction of rotation is correct
Step 1. Use a thin tool to press the PROG button for 2
seconds, until the electric motor cycle.
If the direction of rotation is incorrect
Step 1. Press the STOP button for 2 seconds, until the electric
motor cycles, the direction of rotation was reversed.
Step 2. Press the PROG button for 2 seconds, until the electric
motor cycles.
Register the first remote control on a tubular motor
Step 1. Energize the motor.
Step 2. Press the UP, DOWN buttons on the remote at the
same time.
Step 3. A feedback motion will confirm that the remote has
been temporarily enrolled
in the memory of the tubular motor.
Note: The procedure must be performed within 2 minutes after turning
on the power supply or resetting the electric motor.
Notes: The procedure must be performed within 2 minutes after registering the
first remote control.
The direction of rotation can be reversed over and over again by pressing the
STOP button for 2 seconds before confirming the PROG button for 2 seconds.
The direction of rotation must be confirmed by pressing the PROG button for 2
seconds, and then continue with the programming procedure.
Cycle
1.
1.
1. 2.
3.
2.
Cycle
2 seg.
Cycle
2 seg.

www.tecnoshades.com
SET THE LIMITS OF STROKE
Step 1. Press the UP and STOP button until the electric motor
cycles.
Step 2. Using the UP or DOWN buttons move the motor
where you want to set the upper limit.
Step 3. Press the PROG button for 2 seconds, until the electric
motor cycles.
MODO USER MODE
ADD A REMOTE
Step 1. Press the programming button with a thin tool on the
already registered remote/channel for four seconds, until the
motor cycles.
Step 2. Select the new remote/channel you wish to add and
press its PROG button for two seconds, until the motor cycles.
Note: the procedure must be performed after confirming the direction of
rotation. The order of setting limits does not matter.
Before setting stroke limits, the electric motor runs in stepping mode.
Note: The procedures must be performed within 2 minutes, otherwise the electric
motor will cycle and return to the previous state.
Programming can be canceled by pressing “UP+STOP+DOWN” for 0.5
seconds before confirming by pressing the PROG button for 2 seconds.
Note: You can add up to 12 remote controls to one electric motor.
1.
2.
3.
1.
2.
3.
2.
1.
Cycle
Cycle
o
Set upper limit
Step 1. Press the DOWN and STOP button until the electric
motor cycles.
Step 2. Using the UP or DOWN buttons move the motor
where you want to set the lower limit.
Step 3. Press the PROG button for 2 seconds, until the electric
motor cycles.
Set lower limit
Cycle
Cycle
o
Cycle
Cycle
4 seg.
2 seg.

www.tecnoshades.com
Step 1. Press the programming button with a thin tool on the
already registered remote/channel for four seconds, until the
motor cycles.
Step 2. Select already registered remote/channel you want
to delete and press its PROG button for two seconds, until the
motor cycles, the remote/channel has been deleted.
Modify the upper limit
Step 1. Press the PROG button for four seconds, until the
electric motor cycles.
Step 2. Press the UP and STOP button for two seconds, until
the motor cycles.
Step 3. Press the UP or DOWN button then stop the motor
where you want to set the new limit.
Step 4. Press the PROG button for two seconds until the
electric motor cycles.
Modify the lower limit
Step 1. Press the PROG button for four seconds, until the
electric motor cycles.
Step 2. Press the DOWN and STOP button for two seconds,
until the motor cycles.
Step 3. Press the UP or DOWN button then stop the motor
where you want to set the new limit.
Step 4. Press the PROG button for two seconds until the
electric motor cycles.
DELETE A REMOTE CONTROL
USER MODE
SET THE LIMITS OF STROKE
1.
2.
Cycle
Cycle
Cycle
4 seg.
2 seg.
2 seg.
o
1.
1.
2.
3.
4.
2.
3.
4.
Note: A remote cannot delete itself.
Note: In the adjustment process the electric motor works in stepping mode.
Ciclo
4 seg.
2 seg.
Cycle
4 seg.
2 seg.
2 seg.
o

www.tecnoshades.com
Step 1. Press the PROG button for four seconds until the
electric motor cycles.
Step 2. Press the STOP button for two seconds until the
electric motor cycles.
Step 3. Press the PROG button for two seconds until the
electric motor cycles.
Step 1. Disconnect the power supply for 2 seconds.
Step 2. Connect the power supply for 5 to 15 seconds.
Step 3. Disconnect the power supply for 2 seconds.
Step 4. Connect the power supply, the motor will cycle.
Step 5. Press the PROG button on the new remote for 0.5
seconds, until the electric motor cycles; The new remote has
been programmed and all registered remotes will be
deleted.
Step 1. Press the PROG button for four seconds, until the
motor cycles.
Step 2. Press the UP and DOWN buttons at the same time
for 2 seconds, until the motor cycles.
Step 3. Press the PROG button for 2 seconds, until the
electric motor cycles.
1.
2.
3.
1. 2.
3.
5.
1.
2.
3.
4.
CHANGING THE DIRECTION OF ROTATION
REPLACE THE REMOTE CONTROL
RESET ENGINE
Note: The operation will delete all registered remote controls; however the
motor will retain the stroke limits.
Notes: Any other operation will interrupt the reset process.
The procedure will remove all registered remote controls and stroke limits, the
engine will return to factory condition.
After the electric motor is reset, you have two minutes to register a remote (see step
1, "Initial Programming").
Cycle
4seg.
2 seg.
2 seg.
Cycle
Cycle
2 seg.
2 seg.
2seg.
5 seg.
a 15 seg.
Cycle
Cycle
0.5 seg.
2seg.
Ciclo
4 seg.
2seg.