Sonoff DIY D1 User manual

User manual V1.0
Wi-Fi Smart Dimmer Switch
·中文--------------1 - 3
·Deutsch -------------8-11
·Français ----------16-19
·Русский яз ык-----24-27
·English -------- 4 - 7
·Español ------12-15
·Italiano-------20-23

SONOFF TECHNOLOGIES CO., LTD.
English
Specifications
Model
Input
D1
100-240VAC50/60Hz
100-240VAC50/60Hz
Output
Light Load
Incandescent：200W LED:150W
Operating systems （Android 4.1 & iOS 9.0）or higher
Wi-Fi
IEEE 802.11 b/g/n 2.4GHz
PC
Material
Dimension
62x47x32.5mm
Features
D1 is a Wi-Fi smart dimmer switch that is used toadjust
the light brightness and set various atmosphere for your
room. You can remotely turn on/offlight of your home
anywhere, schedule it on/off, or share it with your family
tocontrol together.
Remote Control
Single/Countdown
Timing
Voice Control
1

SONOFF TECHNOLOGIES CO., LTD.
English
Share Control
Brightness Adjust ment
Scene Mode
Sync Status
LAN Control
2

SONOFF TECHNOLOGIES CO., LTD.
English
Buttons
Functions
On
Off
Short press for the low brightness, long press
toturn down the brightness
Short press for the medium brightness, long
press to turn down the brightness
Short press for the higher brightness, long
press to turn upthe brightness
Short press for the high brightness, long press
toturn up the brightness
Long press for 5s until you hear “Bi Bi” and
release, then the remote controller is cleared
successfully. If you need to use, short press
any button within 5s after powering on again
and you will hear “Bi”, which indicates the
remote controller ispaired successfully.
Long press for 5s until the connected light
enters the breathing mode, which indicates
the device enters quick pairing mode (Touch),
then you can add the light on eWeLink APP.
In quick pairing mode, you can short press
any button on the remote controller to exit this
mode.
3

SONOFF TECHNOLOGIES CO., LTD.
English
Factory Reset
Turn on and off3 times on repeatedly or delete the
connected light on eWeLink APP until it enters “breathing
mode”, then the device is reset successfully and enters
quick pairing mode (Touch).
D1
Setting
Delete
Please reset the switch to factory defaults ifyou want to
use other Wi-Fi networks, then reconnect the network.
4

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in aresidential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interferenceto radio or television reception, which
can be determined by turning the equipment offand on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable
exposure condition without restriction.
FCC ID: 2APN5D1
Shenzhen SonoffTechnologies Co., Ltd.
Room 1001, 10F, Building 8, Lianhua Industrial Park,
Longyuan Road,Longhua District, Shenzhen, GD,
China
https://sonoff.tech
MADE IN CHINA