Sonoma 53SNR5504MET User manual

PART LIST QUANTITY
A
1 PC
B
1 PC
C
1 PC
D
1 PC
E
4 PCS
F
1 PC
G
1 PC
H
4 PCS
I 12 PCS + 1 PC
J 4 PCS + 1 PC
K 2 PCS + 1 PC
L 2 PCS + 1 PC
M 10 PCS + 1 PC
N
1 PC
FLAT WASHER
ALLEN WRENCH
MEDIUM BOLT
( 1/4 in. X 1 3/16 in. )
LONG BOLT
( 1/4 in. X 1 1/4 in. )
LOCK WASHER
FOR MISSING OR INCORRECT PARTS/HARDWARE, CONTACT THE MANUFACTURER'S CUSTOMER SERVICE DIRECTLY AT
1-800-737-5267 OR [email protected]
REFER TO LAST PAGE FOR ADDITIONAL CUSTOMER SERVICE DETAILS.
BACKREST
CAPS ( FOR 24 in. COUNTER STOOL)
SHORT BOLT
( 1/4 in. X 1/2 in. )
FOOT RING
LEG EXTENSION
SEAT
SWIVEL UNIT
BOTTOM LEG FRAME
TOP LEG FRAME
SAVE THESE INSTRUCTIONS
SONOMA SHELTON STOOL ASSEMBLY INSTRUCTIONS
STYLE #:
53SNR5504MET/63SNRSE05BR
ASSEMBLE ON A FLAT, PROTECTED SURFACE
FIGURE
DESCRIPTION
Page 1/3

STYLE #:53SNR5504MET/63SNRSE05BR
STEP 3
A. CONNECT FOOT RING (D) TO ASSEMBLED LEG
FRAMES (B,C) WITH MEDIUM BOLTS (J) SUING
ALLEN WRENCH (N). TIGHTEN COMPLETELY.
STEP 2
A. PLACE SEAT (F) UPSIDE DOWN ON A FLAT,
PROTECTED SURFACE.
B. CONNECT ASSEMBLED LEGS WITH SWIVEL UNIT
(A) TO SEAT (F) USING FLAT WASHERS (M) AND
SHORT BOLTS (I) USING ALLEN WRENCH (N).
TIGHTEN COMPLETELY.
STEP 1
A. ASSEMBLE LEG FRAMES (B, C) BY ALIGNING LEG
FRAME (C) WITH THE CENTER SLOT ON BOTTOM OF
CROSSBAR, ON TOP OF LEG FRAME (B) WITH THE
CENTER SLOT ON TOP OF THE CROSSBAR.
B. TURN SWIVEL UNIT (A) SO THAT THE TWO
SWIVEL PLATES ARE OFFSET AND IN A STAR
PATTERN AS SHOWN. PLEASE NOTE: SWIVEL UNIT
(A) MUST HAVE SMOOTH FLAT HEAD DOWN
TOWARD LEGS.
C. FASTEN SWIVEL UNIT (A) TO LEG FRAMES (B,C)
WITH SHORT BOLTS (I) AND FLAT WASHERS (M)
USING ALLEN WRENCH (N). TIGHTEN COMPLETELY.
ASSEMBLY INSTRUCTIONS (CONTINUED)
Page 2/3

ASSEMBLY INSTRUCTIONS (CONTINUED)
** FOR REPLACEMENT PARTS OR FOR ADDITIONAL INFORMATION,
CALL 1-800-737-5267 BETWEEN 8:00AM AND 5:00PM, CST.
EMAIL: [email protected]
STYLE #:53SNR5504MET/63SNRSE05BR
STEP 4
A. 24 INCH COUNTER STOOL - PLACE CAPS (H) ON
LEG FRAMES AS SHOWN.
B. 29 INCH COUNTER STOOL - INSERT THE LEG
EXTENSIONS (E) INTO LEG FRAMES (B,C) ALIGNING
HOLES PROPERLY.
C. CONNECT THE LEG EXTENSIONS (E) TO THE LEG
FRAMES (B,C) WITH SHORT BOLTS (I) USING ALLEN
WRENCH (N). TIGHTEN COMPLETELY.
STEP 5
A. TURN ASSEMBLED UNIT TO ITS UPRIGHT
POSITION.
B. CONNECT BACKREST (G) TO SEAT (F) OF THE
ASSEMBLED STOOL WITH LONG BOLTS (K), LOCK
WASHERS (L), AND FLAT WASHERS (M) USING
ALLEN WRENCH (N). TIGTHEN COMPLETELY.
C. ASSEMBLY IS COMPLETE.
WARRANTY
** WE RECOMMEND THAT YOU SAVE THE ALLEN WRENCH (N) AND PERIODICALLY TIGHTEN ALL BOLTS .
CARE AND CLEANING
WIPE CLEAN WITH A SOFT, DRY CLOTH AS NEEDED.
WEIGHT LIMIT
300 LBS
DO NOT STAND OR CLIMB ON THE STOOL.
INTENDED FOR INDOOR USE ONLY
Page 3/3