Sonoma 71SNRST01 User manual

PART LIST QUANTITY
A
1 PC
B
1 PC
C
1 PC
D
1 PC
E
1 PC
F
1 PC
G
1 PC
H
1 PC
I
1 PC
J
12 PCS + 1 PC
K
12 PCS + 1 PC
STYLE #: 71SNRST01
CAM BOLT
BACK PANEL
CAM LOCK
LEFT SIDE
RIGHT SIDE
MIDDLE SHELF
RIGHT DOOR
SAVE THESE INSTRUCTIONS
SONOMA CANTON GLASS CABINET ASSEMBLY INSTRUCTIONS
ASSEMBLE ON A FLAT, PROTECTED SURFACE.
PHILLIPS HEAD SCREWDRIVER NEEDED FOR ASSEMBLY; NOT INCLUDED.
FIGURE
DESCRIPTION
TOP
FRONT CROSSBAR
LEFT DOOR
BOTTOM
Page 1/8

PART LIST QUANTITY
L
12 PCS + 1 PC
M
2 PCS + 1 PC
N
3 PCS + 1 PC
O
22 PCS + 1 PC
P
4 PCS + 1 PC
Q
2 PCS
R
2 PCS
S
2 PCS + 1 PC
T
24 PCS + 1 PC
U
4 PCS
V 1 PC
W 1 PC
HINGE
TOUCH-UP PEN
GLUE
MAGNETIC CATCH
KNOB
MEDIUM SCREW
(Dia. 3 mm x 15 mm L)
SHORT SCREW
(Dia. 3 mm x 12 mm L)
LONG WOOD DOWEL
(Dia. 8 mm x 30 mm L)
SHORT WOOD DOWEL
(Dia. 8 mm x 20 mm L)
HINGE SCREW
(Dia. 3.5 mm x 14 mm L)
FIGURE
LONG SCREW
(Dia. 8 mm x 30 mm L)
KNOB BOLT
(Dia. 5/32” x 3/4” L)
DESCRIPTION
SAVE THESE INSTRUCTIONS
SONAMA CANTON GLASS CABINET ASSEMBLY INSTRUCTIONS (CONTINUED)
STYLE #: 71SNRST01
ASSEMBLE ON A FLAT, PROTECTED SURFACE.
PHILLIPS HEAD SCREWDRIVER NEEDED FOR ASSEMBLY; NOT INCLUDED.
Page 2/8

STYLE #: 71SNRST01
STEP 3
A. ATTACH MAGNETIC CATCHES (Q) TO FRONT CROSSBAR
(F) WITH MEDIUM SCREWS (P) USING PHILLIPS HEAD
SCREWDRIVER, NOT INCLUDED. TIGHTEN COMPLETELY.
STEP 2
A. PLACE TOP (A) UPSIDE DOWN ON A FLAT, PROTECTED
SURFACE.
B.PLACE A SMALL AMOUNT OF GLUE (V) IN DOWEL HOLES
ON TOP (A). INSERT SMALL WOOD DOWELS (M).
C. PLACE A SMALL AMOUNT OF GLUE (V) ON THE TOPS OF
SMALL WOOD DOWELS (M).
D. ATTACH FRONT CROSSBAR (F) TO TOP (A) WITH LONG
WOOD SCREWS (N) USING PHILLIPS HEAD SCREWDRIVER,
NOT INCLUDED. TIGHTEN COMPLETELY.
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 1
A. INSERT CAM BOLTS (K) INTO THE PRE-DRILLED SMALL
HOLES ON TOP (A), LEFT SIDE (C), AND RIGHT SIDE (D)
USING PHILLIPS HEAD SCREWDRIVER, NOT INCLUDED.
TIGHTEN COMPLETELY.
K
C
D
A/C/D
A
N
N
N
M
M
A
F
FINISHED EDGE
A
F
P
Q
MAGNETS FACE FORWARD
Page 3/8

STEP 4
A. PLACE LEFT SIDE (C) ON A FLAT, PROTECTED SURFACE.
B. PLACE A SMALL AMOUNT OF GLUE (V) IN DOWEL HOLES
ON LEFT SIDE (C). INSERT LONG WOOD DOWELS (L).
C. PLACE A SMALL AMOUNT OF GLUE (V) ON THE TOPS OF
LONG WOOD DOWELS (L).
D. ATTACH BOTTOM (B) AND MIDDLE SHELF (E).
STEP 6
A. INSERT CAM LOCKS (J) ON BOTTOM SHELF (B) AND
MIDDLE SHELF (E).
B. TURN CAM LOCKS USING PHILLIPS HEAD SCREWDRIVER,
NOT INCLUDED, TO SECURE BOTTOM SHELF (B) AND
MIDDLE SHELF (E) TO LEFT SIDE (C) AND RIGHT SIDE (D).
STYLE #: 71SNRST01
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 5
A. PLACE A SMALL AMOUNT OF GLUE (V) IN DOWEL HOLES
ON BOTTOM SHELF (B) AND MIDDLE SHELF (E). INSERT
LONG WOOD DOWELS (L).
B. PLACE A SMALL AMOUNT OF GLUE (V) ON THE TOPS OF
LONG WOOD DOWELS (L).
C. ATTACH RIGHT SIDE (D).
STEP 7
A. ROTATE ASSEMBLED UNIT TO STANDING POSITION.
B. PLACE A SMALL AMOUNT OF GLUE (V) IN DOWEL HOLES
ON THE TOP END OF LEFT SIDE (C) AND RIGHT SIDE (D).
INSERT LONG WOOD DOWELS (L).
C. PLACE A SMALL AMOUNT OF GLUE (V) ON THE TOPS OF
LONG WOOD DOWELS (L) OF LEFT SIDE (C) AND RIGHT SIDE
(D).
D. ATTACH TOP (A) TO LEFT SIDE (C) AND RIGHT SIDE (D).
C
E
B
L
C
E
B
L
D
D
B
E
C
J
A
L
C
D
BACK VIEW
Page 4/8

STEP 9
A. PLACE ASSEMBLED UNIT FACE DOWN ON A FLAT,
PROTECTED SURFACE.
B. UNFOLD BACK PANEL (I) AND PLACE ON BACK OF
ASSEMBLED UNIT.
C. ATTACH BACK PANEL (I) TO ASSEMBLED UNIT WITH
SHORT SCREWS (O) USING PHILLIPS HEAD SCREWDRIVER,
NOT INCLUDED.
D. ROTATE THE ASSEMBLED UNIT TO STANDING POSITION.
STEP 10
A. ATTACH HINGES (U) TO LEFT DOOR (G) AND RIGHT DOOR
(H) WITH HINGE SCREWS (T) USING PHILLIPS HEAD
SCREWDRIVER, NOT INCLUDED.
STEP 8
A. INSERT CAM LOCKS (J) ON LEFT SIDE (C) AND RIGHT SIDE
(D).
B. TURN CAM LOCKS USING PHILLIPS HEAD SCREWDRIVER,
NOT INCLUDED, TO SECURE TOP (A) TO LEFT SIDE (C) AND
RIGHT SIDE (D).
ASSEMBLY INSTRUCTIONS (CONTINUED)
STYLE #: 71SNRST01
T
U
T
U
T
U
T
U
H
G
I
I
O
D
B
I
C
J
A
C
D
BACK VIEW
Page 5/8

STEP 12
A. ATTACH KNOBS (R) TO LEFT DOOR (G) AND RIGHT DOOR
(H) WITH KNOB BOLTS (S) USING PHILLIPS HEAD
SCREWDRIVER, NOT INCLUDED.
B. ADJUST LEVELERS ON BOTTOM AT FRONT OF CABINET
UNTIL THE UNIT IS STABLE.
C. ASSEMBLY IN COMPLETE.
STEP 11
A. ATTACH LEFT DOOR (G) TO LEFT SIDE (C) WITH HINGE
SCREWS (T) USING PHILLIPS HEAD SCREWDRIVER, NOT
INCLUDED.
B. ATTACH RIGHT DOOR (H) TO RIGHT SIDE (D) WITH HINGE
SCREWS (T) USING PHILLIPS HEAD SCREWDRIVER, NOT
INCLUDED.
ASSEMBLY INSTRUCTIONS (CONTINUED)
STYLE #: 71SNRST01
A
D
C
G
H
U
G/H
C/D
T
C/D
LEVELER
H
G
G/H
S
R
D
C
A
Page 6/8

PART LIST QUANTITY
1 2 PCS
2 2 PCS
3 4 PCS
4 2 PCS
5 2 PCS
STYLE #: 71SNRST01
DESCRIPTION
ZIP TIE
LONG SCREW
(Dia. 4 mm x 38 mm L)
WALL ANCHOR
STEP 2
A. DETERMINE WHERE THE CABINET IS TO BE PLACED,
THEN MARK THE POSITION ON THE WALL SO THE WALL
ANCHORS (4) WILL ALIGN WITH THE METAL "L" BRACKETS
(3) ON THE BACK OF THE CABINET.
B. DRILL HOLES IN THE WALL. PRESS WALL ANCHORS (4)
INTO THE HOLES.
C. ATTACH REMAINING METAL "L" BRACKETS (3) INTO THE
WALL ANCHORS (4) USING LONG SCREWS (1) WITH
PHILLIPS HEAD SCREWDRIVER, NOT INCLUDED.
STEP 1
A. ATTACH THE METAL "L" BRACKETS (3) TO THE BACK OF
THE CABINET BY INSERTING SHORT SCREWS (2) INTO THE
PILOT HOLES USING PHILLIPS HEAD SCREWDRIVER, NOT
INCLUDED.
PLEASE CONSULT A REPRESENTATIVE AT A HARDWARE/HOME IMPROVEMENT STORE TO DISCUSS
ADDITIONAL MOUNTING OPTIONS FOR OTHER TYPES OF WALLS.
PHILLIPS HEAD SCREWDRIVER, DRILL, & 7/16" DRILL BIT NEEDED FOR ASSEMBLY; NOT INCLUDED.
FOR SAFETY REASONS, INSTALL THIS PRODUCT USING THE INCLUDED ANTI-TIP HARDWARE TO HELP PREVENT THE PRODUCT FROM
UNEXPECTEDLY TIPPING OR SHIFTING.
THE INCLUDED MATERIALS ARE DESIGNED TO MOUNT THE ANTI-TIP HARDWARE TO DRYWALL.
ANTI-TIP HARDWARE MOUNTING INSTRUCTIONS FOR DRYWALL
FIGURE
METAL "L" BRACKET
SHORT SCREW
(Dia. 4 mm x 19 mm L)
WALL
WALL
WALL
4
4
4
4
3
1
3
2
Page 7/8

INTENDED FOR INDOOR USE ONLY.
**FOR REPLACEMENT PARTS OR FOR ADDITIONAL INFORMATION,
CALL: 1-866-942-5362 BETWEEN 8:30 A.M. AND 4:30 P.M., PST, MONDAY - FRIDAY.
EMAIL: [e-mail]
TOP PANEL: 100 LBS; SHELVES: 50 LBS
CARE AND CLEANING
WIPE CLEAN WITH A SOFT, DRY CLOTHS AS NEEDED.
WEIGHT LIMIT
STEP 3
A. ALIGN METAL "L" BRACKETS (3) ON BACK OF CABINET TO
THE METAL "L" BRACKETS (3) ON WALL.
B. FEED ZIP TIES (5) THROUGH METAL "L" BRACKETS (3) TO
CONNECT CABINET TO WALL.
C. CHECK TO MAKE SURE ZIP TIES (5) ARE SECURELY
TIGHTENED.
** WE RECOMMEND THAT YOU PERIODICALLY TIGHTEN ALL SCREWS USING PHILLIPS HEAD SCREWDRIVER, NOT INCLUDED.
ANTI-TIP HARDWARE MOUNTING INSTRUCTIONS FOR DRYWALL (CONTINUED)
DO NOT SIT, STAND, OR CLIMB ON THE CABINET.
STYLE #: 71SNRST01
WALL
Page 8/8