Sonoma 71SRRWK43 User manual

Page 1/5
PART LIST QUANTITY
A1 PC
B1 PC
C1 PC
D1 PC
E1 PC
F6 PCS + 1 PC
G4 PCS + 1 PC
H10 PCS + 1 PC
I8 PCS + 1 PC
J4 PCS + 1 PC
K2 PCS + 1 PC
L4 PCS + 1 PC
M4 PCS + 1 PC
N2 PCS
O1 PC
P1 PC
STYLE #: 71SRRWK43
CUSHION
LONG BOLT
(M6*40MM)
SHORT BOLT
(M6*25MM)
ALLEN WRENCH
LARGE FLAT WASHER
(M8)
LOCK WASHER
SEAT
BACK
WRENCH
SMALL FLAT WASHER
(M6)
BASE
PLATE
HEX BOLT
(M8*35MM)
NUT
LEFT ARM
RIGHT ARM
SAVE THESE INSTRUCTIONS
SONOMA BISCAY MOTION CHAIR ASSEMBLY INSTRUCTIONS
ASSEMBLE ON A FLAT, PROTECTED SURFACE.
FIGURE DESCRIPTION

Page 2/5
STEP 1
A. PLACE RIGHT ARM (B) ON A FLAT, PROTECTED SURFACE.
B. ATTACH BACK (D) TO RIGHT ARM (B) WITH LONG BOLTS (F) AND
SMALL FLAT WASHERS (H) USING ALLEN WRENCH (O). DO NOT
TIGHTEN COMPLETELY.
C. ATTACH LEFT ARM (A) TO BACK (D) WITH LONG BOLTS (F) AND
SMALL FLAT WASHERS (H) USING ALLEN WRENCH (O). DO NOT
TIGHTEN COMPLETELY.
STEP 2
A. ROTATE PREASSEMBLED UNIT UPSIDE DOWN.
B. CONNECT SEAT (C) TO BACK (D) WITH LONG BOLTS (F) AND SMALL
FLAT WASHERS (H) USING ALLEN WRENCH (O). DO NOT TIGHTEN
COMPLETELY.
C. CONNECT SEAT (C) TO LEFT ARM (A) AND RIGHT ARM (B) WITH
SHORT BOLTS (G) AND SMALL FLAT WASHERS (H) USING ALLEN
WRENCH (O). DO NOT TIGHTEN COMPLETELY.
D. TIGHTEN COMPLETELY ALL BOLTS (F & G) FROM STEPS 1 & 2 USING
ALLEN WRENCH (O).
ASSEMBLY INSTRUCTIONS (CONTINUED)
STYLE #: 71SRRWK43

Page 3/5
STEP 3
A. CONNECT BASE (E) TO PREASSEMBLED UNIT WITH HEX BOLTS (L),
LOCK WASHERS (J), LARGE FLAT WASHERS (I), PLATES (K), AND NUTS
(M) USING WRENCHES (N). TIGHTEN COMPLETELY.
STEP 4
A. ROTATE ASSEMBLED UNIT TO THE STANDING POSITION.
B. PLACE CUSHION (P) ON SEAT (C).
C. ASSEMBLY IS COMPLETE.
ASSEMBLY INSTRUCTIONS (CONTINUED)
STYLE #: 71SRRWK43

Page 4/5
PART LIST QUANTITY
A1 PC
B2 PCS
C2 PCS
D1 PC
E12 PCS + 1 PC
F12 PCS + 1 PC
G1 PC
STYLE #: 71SRRWK43
TOP FRAME
LEG CONNECTOR
GLASS TOP
BOLT
(M6*15MM)
FLAT WASHER
ALLEN WRENCH
SAVE THESE INSTRUCTIONS
SONOMA BISCAY TABLE ASSEMBLY INSTRUCTIONS
ASSEMBLE ON A FLAT, PROTECTED SURFACE.
FIGURE DESCRIPTION
LEG

Page 5/5
CARE AND CLEANING
FRAME: WIPE CLEAN WITH A SOFT, DAMP CLOTH AS NEEDED.
CUSHION: SPOT CLEAN WITH A DAMP, CLEAN CLOTH AS NEEDED.
DO NOT STAND OR CLIMB ON THE CHAIR.
DO NOT SIT, STAND, OR CLIMB ON THE TABLE.
WARRANTY
1 YEAR LIMITED WARRANTY. COMMERCIAL USE, ACTS OF NATURE, FIRE, FREEZING, ABUSIVE USE,
DISCOLORATION OR FADING OF THE FINISH OR FABRICS AS RESULT OF CHEMICALS OR SPILLS IS NOT
COVERED. PROOF OF PURCHASE (DATED RECEIPT) IS REQUIRED FOR WARRANTY CLAIMS. WE
RESERVE THE RIGHT TO MAKE SUBSTITUTIONS WITH SIMILAR MERCHANDISE.
STEP 1
A. PLACE TOP FRAME (A) UPSIDE DOWN ON A FLAT,
PROTECTED SURFACE.
B. ATTACH LEGS (B) TO TOP FRAME (A) WITH BOLTS (E)
AND FLAT WASHERS (F) USING ALLEN WRENCH (G). DO
NOT TIGHTEN COMPLETELY.
STEP 2
A. ATTACH LEG CONNECTERS (C) TO LEGS (B) WITH
BOLTS (E) AND FLAT WASHERS (F) USING ALLEN
WRENCH (G). DO NOT TIGHTEN COMPLETELY.
B. TIGHTEN COMPLETELY ALL BOLTS (E) WITH ALLEN
WRENCH (G).
STEP 3
A. ROTATE ASSEMBLED UNIT TO THE UPRIGHT
POSITION.
B. PLACE GLASS TOP (D) ON TOP FRAME (A).
C. ADJUST LEVELERS ON BOTTOM SO THE TABLE IS
STABLE ON THE FLOOR.
D. ASSEMBLY IS COMPLETE.
STYLE #: 71SRRWK43
ASSEMBLY INSTRUCTIONS (CONTINUED)
WEIGHT LIMIT
CHAIR: 300 LBS; TABLE: 50 LBS
** WE RECOMMEND THAT YOU SAVE THE ALLEN WRENCH & WRENCH AND PERIODICALLY TIGHTEN ALL BOLTS.
D