Sonoma 53SNR2001BAS User manual

SAVE THESE INSTRUCTIONS
CONSOLE TABLE ASSEMBLY INSTRUCTIONS
STYLE #: 53SNR2001BAS
ASSEMBLE ON A FLAT, PROTECTED SURFACE
PHILLIPS HEAD SCREWDRIVER NEEDED FOR ASSEMBLY; NOT INCLUDED
PART LIST FIGURE UANTITY DESCRIPTION
AA 1 PC TOP
B 1 PC LEFT SIDE FRAME
C 1 PC RIGHT SIDE FRAME
D 1 PC BACK PANEL
E 2 PCS TOP CROSSBAR
F 1 PC MIDDLE FRONT CROSSBAR
G 1 PC MIDDLE BACK STRETCHER
H 1 PC PARTITION PANEL
I 1 PC BOTTOM SHELF
J 1 PC BOTTOM BACK STRETCHER
K 2 PCS DRAWER FRONT
L 2 PCS DRAWER LEFT SIDE
M 2 PCS DRAWER RIGHT SIDE
N 2 PCS DRAWER BACK PANEL
Page 1/10

SAVE THESE INSTRUCTIONS
CONSOLE TABLE ASSEMBLY INSTRUCTIONS
STYLE #: 53SNR2001BAS
ASSEMBLE ON A FLAT, PROTECTED SURFACE
PHILLIPS HEAD SCREWDRIVER NEEDED FOR ASSEMBLY; NOT INCLUDED
Page 2/10
PART LIST FIGURE UANTITY DESCRIPTION
O 2 PCS DRAWER BOTTOM PANEL
P 4 PCS DRAWER GLIDES
Q 8 PCS + 1 PC SMALL CAM LOCK
(Dia. 1 mm x 9 mm)
R 2 PCS + 1 PC LARGE CAM LOCK
(Dia. 1 mm x 12 mm)
S 33 PCS + 1 PC CAM PIN
(Dia. 6 mm x 3 mm L)
T 8 PCS + 1 PC SHORT SCREW
(Dia. 3. mm x 19 mm L)
U 6 PCS + 1 PC MEDIUM SCREW
(Dia. 4 mm x 2 mm L)
V 8 PCS + 1 PC LONG SCREW
(Dia. 4 mm x 32 mm L)
W 4 PCS + 1 PC X-LONG SCREW
(Dia. 4 mm x 0 mm L)
X 2 PCS KNOB
(Dia. 31. mm x 24. mm)
Y 2 PCS KNOB BOLT
(Dia. /32” x 3/4” L)
Z 4 PCS METAL BRACKET
(18 mm x 18 mm x 18 mm)
AA 20 PCS + 1 PC SLIDES SCREW
(Dia. 3. mm x 12 mm L)
BB 4 PCS + 1 PC SMALL WOOD DOWEL
(Dia. 6 mm x 20 mm L)
CC 18 PCS + 1 PC LARGE WOOD DOWEL
(Dia. 8 mm x 30 mm L)
DD 1 PC TOUCH-UP PEN
EE 1 PC GLUE

Page 3/10
STEP 2
A. ATTACH THE INTERNAL SLIDE RUNNERS
FROM DRAWER GLIDES (P) TO BOTH
DRAWER LEFT AND RIGHT SIDE PANELS (L &
M) WITH SLIDES SCREWS (AA). ENSURE THE
OPEN END OF INTERNAL SLIDE RUNNER
POINTS TOWARDS THE SIDE WITH SCREW
HOLES OF DRAWER SIDE PANELS (L & M).
STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 3
A. SECURELY SCREW CAM PINS (S) INTO THE
DESIGNATED SMALL HOLES ON DRAWER
FRONT (K).
B. ATTACH DRAWER SIDE PANELS (L & M) TO
DRAWER FRONT (K) USING SMALL CAM
LOCKS (Q) MAKING SURE THE GROOVES
FACE INWARD AND LINE UP WITH EACH
OTHER.
STEP 1
A. SEPARATE THE DRAWER GLIDES (P) COMPONENTS BY
EXTENDING THE INTERNAL SLIDE RUNNER ALL THE
WAY FORWARD. PRESS THE PLASTIC RELEASE LEVER
OF THE DRAWER GLIDE UP AND PULL THE INTENAL
SLIDE RUNNER COMPLETELY OUT.
B. REPEAT FOR THE OTHER DRAWER GLIDES.
SCREW HOLES
OPEN END
SCREW HOLES
P
P
P
L/M
P
P
M
L
MOUNTING HOLES
OPEN END
AA
M
L
K
K
K
L/M
Q
S
S
FINISHED EDGE
RAW EDGE

STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 4
A. SLIDE DRAWER BOTTOM PANEL (O) INTO THE
GROOVES BETWEEN THE DRAWER SIDE PANELS
(L & M) UNTIL FULLY INSERTED INTO THE
DRAWER FRONT (K).
STEP 6
A. ATTACH KNOB (X) TO THE OUTSIDE OF
DRAWER FRONT (K) WITH KNOB BOLT (Y).
B. REPEAT THE SAME PROCEDURE TO ASSEMBLE
THE SECOND DRAWER.
GROOVE
STEP
A. FASTEN DRAWER BACK PANEL (N) TO DRAWER SIDE
PANELS (L & M) USING LONG SCREWS (V). MAKE
SURE THAT THE DRAWER BOTTOM PANEL (O) FITS
SECURELY INTO THE GROOVE OF THE DRAWER BACK
PANEL (N).
Page 4/10
O
K
L
M
V
V
N
M
O
K
L
L
K
O M
N
Y
X
K
FINISHED SURFACE
FINISHED EDGE

STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 8
A. ATTACH THE SEPARATED OUTER SLIDE TRACKS
(P) TO BOTH SIDES OF PARTITION PANEL (H)
WITH SLIDES SCREWS (AA). ENSURE THE
OPENING OF SLIDE TRACK FACES THE FRONT
EDGE.
NOTE: THERE ARE CAM BOLT HOLES AT THE
BACK EDGE OF PARTITION PANEL.
LEFT SIDE MOUNTING HOLES
P
P
RIGHT SIDE MOUNTING HOLES
SLIDE OPENING
H
P
AA
H
H
LEFT SIDE
RIGHT SIDE
STEP 7
A. SECURELY SCREW CAM PINS (S) INTO
THE DESIGNATED SMALL HOLES ON
BACK PANEL (D).
D
S
FRONT EDGE
SLIDE OPENING
FRONT EDGE
Page 5/10

STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 11
A. ATTACH THE SEPARATED OUTER SLIDE TRACKS (P)
TO LEFT AND RIGHT SIDE FRAMES (B & C) WITH
SLIDES SCREWS (AA). ENSURE THE OPENING OF
THE OUTER SLIDE TRACK FACES THE FRONT LEG.
NOTE: BACK LEG HAS 3 PRE-DRILLED HOLES AND
FRONT LEG HAS ONLY ONE PRE-DRILLED HOLE.
STEP 10
A. ATTACH MIDDLE FRONT CROSSBAR (F) AND
MIDDLE BACK STRETCHER (G) TO PARTITION
PANEL (H) WITH X-LONG SCREWS (W) KEEPING
THE NOTCHES OF FRONT CROSSBAR (F) UP.
THE CAM LOCK HOLES FACE
THE BACK OF UNIT
STEP 9
A. GLUE LARGE WOOD DOWEL (CC) INTO
THE MIDDLE HOLE OF BACK PANEL (D).
B. ATTACH PARTITION PANEL (H) TO BACK
PANEL (D) USING LARGE CAM LOCKS (R)
KEEPING THE CAM PIN HOLES IN BOTH
PARTS FACING THE SAME DIRECTION.
FRONT LEG
FRONT LEG
SLIDE OPENING
CAM PIN HOLES FACE
THE SAME DIRECTION
MOUNTING HOLES
P
P
P
B/C
C
B
AA
SLIDE OPENING
R
CC
D
H
W
H
F
G
D
NOTCHES FACE UP
Page 6/10

STEP 14
A. GLUE LARGE WOOD DOWELS (CC) INTO
THE LARGE HOLES OF BOTTOM SHELF (I).
B. ATTACH BACK STRETCHER (J) TO BOTTOM
SHELF (I) USING LARGE CAM LOCKS (R)
KEEPING CAM LOCKS FACING INSIDE.
C. USING THE PILOT HOLES AS A GUIDE,
FASTEN METAL BRACKETS (Z) AGAINST
THE NOTCHES OF BOTTOM SHELF (I) WITH
SHORT SCREWS (T). BE SURE THE FLAT SIDE
OF METAL BRACKETS FACES OUT. TIGHTEN
SCREWS SECURELY.
STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 13
A. SECURELY SCREW CAM PINS (S) INTO THE
DESIGNATED SMALL HOLES ON BOTTOM
SHELF (I).
STEP 12
A. SECURELY SCREW CAM PINS (S) INTO THE
DESIGNATED SMALL HOLES ON LEFT AND
RIGHT SIDE FRAMES (B & C).
B
S
C
I
S
R
R
R
J
CC
CC
I
Z
T
I
Z I
T
Page 7/10

STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
STEP 1
A. GLUE LARGE WOOD DOWELS (CC)
INTO THE LARGE HOLES OF LEFT
SIDE FRAME (B).
B. ATTACH LEFT SIDE FRAME (B) TO
ASSEMBLY FROM STEP 10 USING
LARGE CAM LOCKS (R).
C. FASTEN ASSEMBLED BOTTOM
SHELF (I) TO LEFT SIDE FRAME (B)
WITH LARGE CAM LOCKS (R).
D. REPEAT THE SAME PROCEDURE TO
ATTACH RIGHT SIDE FRAME (C).
STEP 16
A. FASTEN BOTTOM SHELF (I) TO
LEGS OF SIDE FRAMES (B & C)
WITH SHORT SCREWS (T)
THROUGH THE METAL BRACKETS.
TIGHTEN SCREWS SECURELY.
C
B
I
G
F
CC
CC
R
R
R
R
CC
R
J
D
R
CC
I
J
B
C
B/C
Z
T
I
J
Page 8/10

STEP 18
A. SECURELY SCREW CAM PINS (S)
INTO THE DESIGNATED SMALL
HOLES ON TOP (A).
STEP 17
A. ALIGN AND ATTACH TOP CROSSBARS
(E) TO TOP (A) GLUING SMALL WOOD
DOWELS (BB) AND USING MEDIUM
SCREWS (U).
U
U
U
BB
BB
E
E
A
STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
A
S
FINISHED EDGE
Page 9/10

STYLE #: 53SNR2001BAS
ASSEMBLY INSTRUCTIONS (CONTINUED)
**WE RECOMMEND THAT YOU PERIODICALLY TIGHTEN ALL CAM LOCKS AND WOOD SCREWS.
1. WIPE CLEAN WITH A SOFT, DRY CLOTH AS NEEDED.
2. DO NOT SIT, STAND OR CLIMB ON CONSOLE TABLE.
3. WEIGHT RESTRICTION: TOP: 200 LBS, SHELF: 50 LBS, DRAWER: 10 LBS.
4. INTENDED FOR INDOOR USE ONLY.
**FOR REPLACEMENT PARTS OR FOR ADDITIONAL INFORMATION,
CALL: 1-866-942-5362 BETWEEN 8:30 A.M. AND 4:30 P.M., PST, MONDAY - FRIDAY.
EMAIL:
[email protected]
STEP 19
A. ROTATE THE ASSEMBLED FRAME UPRIGHT.
B. GLUE LARGE WOOD DOWELS (CC) INTO THE LARGE
HOLES OF ASSEMBLY FROM STEP 16.
C. ATTACH TOP (A) TO SIDE FRAMES (B & C), BACK
PANEL (D) AND PARTITION PANEL (H) OF ASSEMBLY
USING LARGE CAM LOCKS (R).
STEP 20
A. INSERT THE ASSEMBLED DRAWERS INTO FRAME TO
FINISH THE ASSEMBLY. SIMPLY PUSH THE BALL
BEARING CART ALL THE WAY TO THE END OF BOTH
SLIDES, THEN ALIGN THE SLIDE RUNNERS ON THE
DRAWER WITH THE SLIDE TRACKS ON THE UNIT.
PUSH DRAWER CAREFULLY INSIDE UNTIL IT STOPS.
NOTE: IF THE DRAWER DOES NOT GO IN SMOOTHLY,
PLEASE TAKE IT OUT AND REPEAT THE STEP.
DRAWER INSTALLATION DRAWER REMOVAL
FRONT
BALL BEARING CART RELEASE LEVER
D
B
C
R H
A
CC
CC CC
R
R
R
A
B
C
L
M
L
M
R
Page 10/10