Southern Enterprises 12877 User manual

For assistance with assembly, contact:
Southern Enterprises Inc.
customer service 1-800-633-5096
[e-mail]
www.seidal.com
MS333400TX – ESPRESSO
LADDER MEDIA STAND
Assembly Instructions
PO#12877

A B
C D
E F
G H
I J
K
L
Quantity
of 1
bottom panel
Quantity
Of 1
left side panel
Quantity
of 1
right side panel
Quantity
Of 1
top center panel
Quantity
of 1
bottom center panel
Quantity
Of 1
back panel
Quantity
of 1
bottom left post
Quantity
Of 1
bottom right post
Quantity
of 1
top left post
Quantity
Of 1
top right post
Quantity
of 1
top panel
Quantity
Of 1
shelf panel
LADDER MEDIA TAND
Parts List
Please review all parts and hardware before disposing of any packaging.
Call customer service if missing hardware.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
screw diagrams below. You may receive extra hardware with your unit.

M
N
O P
Q R
S T
U
drawer back panel
Quantity
of 2
drawer bottom panel
Quantity
of 2
middle leg
Quantity
of 1
bottom shelf panel
Quantity
of 1
drawer front
Quantity
of 2
drawer left side panel
Quantity
of 2
drawer right side panel
Quantity
of 2
top shelf panel
Quantity
of 1
medium shelf panel
Quantity
of 1

(1) (2)
(3) (4)
(5) (6)
(7) (8)
(9) (10)
(11) (12)
(13)
(14)
Quantity
of 20
cam bolt
Quantity
Of 20
cam lock
Quantity
of 36
Quantity
Of 4
Φ5/16”*1”
wood dowel
Φ5/16”*1-3/16”
wood dowel
Quantity
of 10
Φ1/4”*1”
hexagon head bolt
Quantity
Of 10
spring washer
Quantity
of 10
flat washer
Quantity
Of 1
allen wrench
Quantity
of 2
pin
Quantity
Of 4
cross socket nut
Quantity
of 16
Φ5/32*1”
screw
Quantity
Of 16
Φ1/4”*1-3/16”
wood dowel
Quantity
of 2
drawer handle
Quantity
of 4
Φ5/32”*3/4”
bolt

(15) (16)
(17) (18)
(19) (20)
(21) (22)
(23)
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish.Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required
No.2 Phillips Screwdriver (Not Included)
Tool List: 3/16" drill bit, drill, tape measure and pencil.
Quantity
of 12
L bracket
Quantity
of 36
Φ5/32”*7/16”
screw
Quantity
of 6
wooden plug
Quantity
of 24
sticker cover
Quantity
of 4
anti-tip bracket
Quantity
of 2
plastic strap
Quantity
of 2
Quantity
of 2
plastic anchor
Φ5/32”*9/16”
short screw
Quantity
of 2
Φ5/32”*1”
long screw

Insert cam locks (2) into holes on top center
panel (F).
Screw cam bolts (1) into holes on shelf panel
(B).
Insert cam locks (2) into corresponding holes on
panel (F). Attach top center panel (F) to shelf
pane l (B) by inserting wood dowel (3) and cam
bolt (1) into corresponding holes until top center
panel (F) to shelf panel (B) meet. Make sure
finished edges are facing forward.
Secure by rotating cam lock (2) clockwise with
phillips screwdriver.
Cover cam locks (2) with sticker cover (17).
Insert cam locks (2) into holes on bottom center
panel (G).
Screw cam bolts (1) into holes on shelf panel
(B).
Attach bottom center panel (G) to shelf panel (B)
by inserting wood dowel (3) and cam bolt (1) into
corresponding holes until bottom center panel
(G) to shelf panel (B) meet.
Secure by rotating cam lock (2) clockwise with
phillips screwdriver.
Cover cam locks (2) with sticker cover (17).
Insert cam locks (2) into holes on
pre-assembled unit.
Screw cam bolts (1) into holes on right side
panel (E) and left side panel (D).
Attach right side panel (E) and left side panel (D)
to shelf panel (B) by inserting wood dowel (3)
and cam bolt (1) into corresponding holes until
right side panel (E) and left side panel (D) meet
shelf panel (B).
Secure by rotating cam lock (2) clockwise with
phillips screwdriver.
Cover cam lock (2) with sticker cover (17).
LADDER MEDIA TAND
Assembly Instructions
Figure 1
( 2)
( 1)
"Please do not over tighten cam bolts.
Please stop when you feel tight"
Figure 2
Figure 3

Insert cam locks (2) into holes on
pre-assembled unit.
Screw cam bolts (1) into holes on top panel (A).
Attach top panel (A) to right side panel (E), top
center panel (F), and left side panel (D) by
inserting wood dowels (3) and cam bolts (1) into
corresponding holes until top panel (A) meets
panels (E, F, D). Secure by rotating cam lock (2)
clockwise with phillips screwdriver.
Cover cam lock (2) with sticker cover (17).
Slide back panel (H) into grooves of left side
panel (D) and right side panel (E).
Insert cam locks (2) into holes on
pre-assembled unit.
Screw cam bolts (1) into holes on bottom panel
(C).
Attach bottom panel (C) to right side panel (E),
bottom center panel (G), and left side panel (D)
by inserting wood dowel (3) and cam bolt (1) into
corresponding holes until bottom panel (C)
meets panels (E, G, D). Secure by rotating cam
lock (2) clockwise with phillips screwdriver.
Cover cam locks (2) with sticker cover (17).
Figure 4
Figure 5
Figure 6

Insert wood dowel (4) into corresponding holes
on bottom left post (I). Attach bottom left post (I)
to left side panel (D) using hexagon head bolt
(5), spring washer (6), and flat washer (7).
Tighten with allen wrench (8) as shown on inset.
Note: Make sure the angled end on bottom
left post (I) is facing down.
Cover hexagon head bolt (5) with sticker cover
(17).
Insert wood dowel (4) into corresponding holes
on bottom right post (J).Attach bottom right post
(J) to right side panel (E) using hexagon head
bolt (5), spring washer (6), and flat washer (7).
Tighten with allen wrench (8), as shown on
inset.
Note: Make sure the angled end on bottom
right post (J) is facing down.
Cover hexagon head bolt (5) with sticker cover
(17).
Screw middle leg (U) to bottom panel (C).
Insert wood dowel (3) in corresponding holes on
top shelf panel (M), medium shelf panel (N), and
bottom shelf panel (O).
Attach top left post (K) to top shelf panel (M),
medium shelf panel (N), and bottom shelf panel
(O) using hexagon head bolt (5), spring washer
(6), and flat washer (7) as shown on the inset.
Tighten with allen wrench (8).
Note: Make sure the angled edge on shelves
(M), (N), and (O) are facing forward.
Cover hexagon head bolt (5) with wooden plug
(18).
Figure 7
C
E
D
D
E
Figure 8
Figure 9

Insert wood dowel (3) in corresponding holes on
top shelf panel (M), medium shelf panel (N), and
bottom shelf panel (O). Attach top right post (L) to
top shelf panel (M), medium shelf panel (N), and
bottom shelf panel (O) by using hexagon head
bolt (5), spring washer (6), and flat washer (7).
Tighten with allen wrench (8).
Cover hexagon head bolt (5) with wooden plug
(18).
Partially unscrew cross socket nut (10), using
phillips screwdriver, to make room for pin (9) to
be inserted. Insert cross socket nut (10) into
corresponding holes on bottom right post (J) and
bottom left post (I). Insert pin(9) into
corresponding holes on bottom right post (J) and
bottom left post (I), as shown in figure 11. Make
sure pin (9) goes through cross socket nut (10).
Then, screw cross socket nut (10) clockwise to
secure pin in place. Repeat this step for top right
post (L) and top left post (K).
Attach top right post (L) to bottom right post (J),
and attach top left post (K) to bottom left post (I)
using wood dowel (3), Pin (9), and cross socket
nut (10).
Attach L brackets (15) to the edge of top post
and each shelf panel in figure 12. Tighten L
brackets (15) with screw (16) using phillips
screwdriver.
Figure 11
Figure 12
Figure 10

Join drawer front (P) to drawer left side panel
(Q) by using wood dowel (12) and screw (11),
tighten with a phillips screwdriver.
Join drawer back panel (S) to drawer left side
panel (Q) using wood dowel (12) and screw
(11), tighten with a phillips screwdriver.
Slide bottom panel (T) into grooves of drawer
front (P) and drawer back panel (S).
Join drawer right side panel (R) to drawer front
(P) and drawer back panel (S) using wood
dowel (12) and screw (11), tighten with phillips
screwdriver.
Attach drawer handle (13) to drawer front (P)
with bolt (14) tighten with a phillips screwdriver.
Repeat assembly steps for the second drawer.
Slide the two drawers into the pre-fitted metal
slides on left side panel (D), right side panel (E),
and bottom center panel (G). Make sure the
drawers slide smoothly in and out.
Figure 13
Figure 14