Southern Enterprises HZ030500TX User manual

Page |
1
PO#:
HZ030500TX
Wyman Tiered Storage Cabinet
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.s
ei
furniturestore
.com

Page |
2
1) Quantity
of 1
Top Panel
2) Quantity
of 2
Top Side Panel
3) Quantity
of 1
Top Vertical Panel
4) Quantity
of 1
Second Top Panel
5) Quantity
of 4
Third Side Panel
6)Quantity
of 1
Third Top Panel
7) Quantity
Of 1
Second Vertical Panel
8) Quantity
of 1
Third Vertical Panel
9L) Quantity
of 1
Left Top Door Panel
9R) Quantity
of 1
Right Top Door Panel
10L) Quantity
of 1
Middle Left Door Panel
10R) Quantity
of 1
Middle Right Door Panel
Wyman Tiered Storage Cabinet
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.

Page |
3
11L) Quantity
of 1
Bottom Left Door Panel
11R) Quantity
of 1
Bottom Right Door Panel
12) Quantity
of 1
Fourth Top Panel
13) Quantity
of 1
Bottom Panel
14) Quantity
of 1
Top Back Panel
15) Quantity
of 1
Middle Back Panel
16) Quantity
of 1
Bottom Back Panel
17) Quantity
of 1
Adjustable Leg
18) Quantity
of 4
Leg
A)Quantity
o f 30
Cam Bolts
B)Quantity
o f 36
Wood Dowels Dia. 5/16"x1-1/4
C)Quantity
o f 30
Cam Locks
D) Quantity
of 30
Cover
E
) Quantity
of 24
Screw Dia. 1/8” x 1/2”L
F) Quantity
of 6
Bolts Dia. 5/32"x3/4"

Page |
4
G) Quantity
of 6
Knob
H) Quantity
of 12
Screw Dia. 1/8” x 5/8”L
I) Quantity
of 8
Bolts Dia. 1/4”x 1-3/4”L
J) Quantity
of 8
Bolts Dia. 1/4”x 1/2”L
L) Quantity
of 16
Flat Washer
M) Quantity
of 16
Spring Washer
N) Quantity
of 1
Allen Wrench 4MM
O) Quantity
of 6
Magnet
PL) Quantity
of 6
Hinge
PR) Quantity
of 6
Hinge
Q) Quantity
of 4
Iron Bracket
R) Quantity
of 6
Iron Plate
S) Quantity
of 6
Screw Dia. 1/8”*1/2”L
T) Quantity
of 32
Screw Dia. 1/8”*5/8”L
U) Quantity
of 4
Screw Dia.1/8”*5/8L”

Page |
5
V) Quantity
of 4
Bracket
W) Quantity
of 2
Plastic chain
X) Quantity
of 4
Anchor
Y) Quantity
of 4
Screw Dia1/8”x1-3/8”L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
SEI Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver, Hammer
(Not Included)

Page |
6
Figure 1
Attach three Legs (18) to the
Fourth Top Panel (12) with Bolts
(I), Spring Washers (M), and
Flat Washers (L).
Tighten Bolts (I) with Allen
Wrench (N).
Figure 2
Attach Bottom Panel (13) to
pre-assembled unit from Figure
1 with Iron Brackets (Q), Bolts
(J), Spring Washers (M), and
Flat Washers (L).
Tighten Bolts (J) with Allen
Wrench (N).
Attach Adjustable Leg (17) to
pre-assembled unit from Figure
1 by hand.
Wyman Tiered Storage Cabinet
Assembly Instructions
N
N
Q

Page |
7
Figure 3
Attach the Fourth Leg (18) to
pre-assembled unit from Figure
2 with Brackets (Q), Bolts (J/I),
Spring Washers (M), and Flat
Washers (L).
Tighten Bolts (J/I) with Allen
Wrench (N).
Figure 4
Attach Hinges (PL/PR) to
Bottom Left Door Panel (11L)
with Screws (E).
Attach Iron Plate (R) to Bottom
Left Door Panel (11L) with
Screw (S).
Attach Knob (G) to Bottom Left
Door Panel (11L) with Bolt (F).
Tighten Bolt (F) and Screws
(E/S) with Phillips screwdriver
(not included).
N
N
Q
PR
R
PL

Page |
8
Figure 5
Attach Hinges (PL/PR) to
Bottom Right Door Panel (11R)
with Screws (E).
Attach Iron Plate (R) to Bottom
Right Door Panel (11R) with
Screw (S).
Attach Knob (G) to Bottom
Right Door Panel (11R) with
Bolt (F).
Tighten Bolt (F) and Screws
(E/S) with Phillips screwdriver
(not included).
Figure 6
Insert Cam Locks (C) into Third
Side Panels (5) and Third
Vertical Panel (8).
Screw Cam Bolts (A) into
threaded holes on
pre-assembled unit from Figure
3.
Attach Third Side Panels (5)
and Third Vertical Panel (8) to
pre-assembled unit from Figure
3 by inserting Cam Bolts (C)
and Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by
rotating Cam Locks (C)
clockwise using Phillips
screwdriver (not included).
Cover Cam Lock Holes with
Covers (D).
PL
R
D
C

Page |
9
Figure 7
Attach Magnets (O) to Third
Top Panel (6) with Screws (H).
Tighten Screws (H) with Phillips
screwdriver (not included).
Figure 8
Insert Cam Locks (C) into
corresponding holes on
pre-assembled unit from Figure
6.
Screw Cam Bolts (A) into
threaded holes on Third Top
Panel (6).
Attach Bottom Doors (11L/1R)
to pre-assembled unit from
Figure 6 by inserting lower
hinges into corresponding
holes. Upper hinges will
connect to holes in Third Top
Panel (6).
Attach Third Top Panel (6) to
pre-assembled unit from Figure
6 by inserting Cam Bolts (A)
and Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by
rotating Cam Locks (B)
clockwise using Phillips
screwdriver (not included).
O
B

Page |
10
Figure 9
Attach Hinges (PL/PR) to
Middle Left Door Panel (10L)
with Screws (E).
Attach Iron Plate (R) to Middle
Left Door Panel (10L) with
Screw (S).
Attach Knob (G) to Middle Left
Door Panel (10L) with Bolt (F).
Tighten Bolt (F) and Screws
(E/S) with Phillips screwdriver
(not included).
Figure 10
Attach Hinges (PL/PR) to
Middle Right Door Panel (10R)
with Screws (E).
Attach Iron Plate (R) to Middle
Right Door Panel (10R) with
Screw (S).
Attach Knob (G) to Middle Right
Door Panel (10R) with Bolt (F).
Tighten Bolt (F) and Screws
(E/S) with Phillips screwdriver
(not included).
PR
R
PL
PL
R
PR

Page |
11
Figure 11
Insert Cam Locks (C) into Third
Side Panels (5) and Second
Vertical Panel (7).
Screw Cam Bolts (A) into
threaded holes on
pre-assembled unit from Figure
8.
Attach Third Side Panels (5)
and Second Vertical Panel (7)
to pre-assembled unit from
Figure 8 by inserting Cam Bolts
(C) and Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by
rotating Cam Locks (C)
clockwise using Phillips
screwdriver (not included).
Cover Cam Lock Holes with
Covers (D).
Figure 12
Attach Magnets (O) to Second
Top Panel (4) with Screws (H).
Tighten Screws (H) with Phillips
screwdriver (not included).
B
O

Page |
12
Figure 13
Insert Cam Locks (C) into
corresponding holes on
pre-assembled unit from figure
11.
Screw Cam Bolts (A) into
threaded holes on Second Top
Panel (4).
Attached Middle Doors
(10L/10R) to pre-assembled
unit from Figure 11 by inserting
lower hinges into corresponding
holes. Upper hinges will fit into
holes on Second Top Panel (4)
Attach Second Top Panel (4) to
pre-assembled unit from Figure
11 by inserting Cam Bolts (A)
and Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by
rotating Cam Locks (B)
clockwise using Phillips
screwdriver (not included).
B

Page |
13
Figure 14
Attach Hinges (PL/PR) to Top
Left Door Panel (9L) with
Screws (E).
Attach Iron Plate (R) to Top Left
Door Panel (9L) with Screw (S).
Attach Knob (G) to Top Left
Door Panel (9L) with Bolt (F).
Tighten Bolt (F) and Screws
(E/S) with Phillips screwdriver
(not included).
Figure 15
Attach Hinges (PL/PR) to Top
Right Door Panel (9R) with
Screws (E).
Attach Iron Plate (R) to Top
Right Door Panel (9R) with
Screw (S).
Attach Knob (G) to Top Right
Door Panel (9R) with Bolt (F).
Tighten Bolt (F) and Screws
(E/S) with Phillips screwdriver
(not included).
PR
R
PL
PL
R
PR

Page |
14
Figure 16
Attach Magnets (O) to Top
Panel (1) with Screws (H).
Tighten Screws (H) with Phillips
screwdriver (not included)
Figure 17
Insert Cam Locks (C) into Top
Side Panels (2) and Top Vertical
Panel (3).
Screw Cam Bolts (A) into
threaded holes on
pre-assembled unit from Figure
13.
Attach Top Side Panels (2) and
Top Vertical Panel (3) to
pre-assembled unit from Figure
13 by inserting Cam Bolts (A)
and Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by
rotating Cam Locks (C)
clockwise using Phillips
screwdriver (not included).
Cover Cam Lock Holes with
Covers (D).
O
B

Page |
15
Figure 18
Insert Cam Locks (C) into
corresponding holes on
pre-assembled unit from figure
17.
Screw Cam Bolts (A) into
threaded holes on Top Panel
(1).
Attach Top Doors (9L/9R) to
pre-assembled unit from figure
17 by inserting lower hinges
into corresponding holes. Upper
hinges will fit in holes on Top
Panel (1).
Attach Top Panel (1) to
pre-assembled unit from Figure
17 by inserting Cam Bolts (A)
and Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by
rotating Cam Locks (C)
clockwise using Phillips
screwdriver (not included).
Cover Cam Lock Holes with
Covers (D).

Page |
16
Figure 19
Attach Back Panels (14/15/16)
to pre-assembled unit from
Figure 18 with Screws (T).
Tighten Screws (T) with Phillips
screwdriver (not included).
Figure 20
Attach Brackets (V) to Back
Panels (14/15/16) using Screws
(U).
Mark two desired locations on
wall.
Drill two 3/16" holes on wall.
Insert Plastic Anchors (X) into
the 2 holes on wall, tap with
hammer (not included) as
needed.
Attach Brackets (V) to wall
using Screws (Y).
Tighten Screws (U/Y) using a
Philips screwdriver (not
included).
WALL
T

Page |
17
Figure 21
Move this item close to the wall.
Tie Brackets (V) together with
Plastic Chains (W).
Anti-tipping hardware must
be used for this product to
avoid tipping and injury.
Now your Wyman Tiered
Storage Cabinet is ready for
use!
WALL

Page |
18
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas),
Mon-Fri 9am – 4pm CST, or email us at [e-mail]. Please ask for customer service representative for
issues involving damages or replacement parts. Please ask for technical assistance representative for any issues
with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019