Southern Enterprises Talus MS040800TX Installation guide

Page |
1
PO#:
MS040800TX
Talus Media Console
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.sei
furniturestore
.com

Page |
2
1) Quantity
of 1
Top
2) Quantity
of 4
Support
3) Quantity
of 1
Middle Panel
4L) Quantity
of 1
Left Side Panel
4R) Quantity
of 1
Right Side Panel
5L)Quantity
of 1
Left Middle Clapboard
5R) Quantity
of 1
Right Middle Clapboard
6) Quantity
of 1
Bottom Panel
7R) Quantity
of 1
Left Door Panel
7L) Quantity
of 1
Right Door Panel
8) Quantity
of 2
Side Adjustable Shelf
9) Quantity
of 1
Middle Adjustable Shelf
Talus Media Console
Parts List
Please check packaging for all parts and hardware before discarding. Before beginning assembly, separate each
type of hardware. Carefully study the diagrams below and check that you have all parts indicated.
Call Customer Service if missing any hardware. Using the incorrect hardware will cause damage.

Page |
3
10) Quantity
of 4
Leg
11) Quantity
of 1
Adjustable Leg
12) Quantity
of 1
Back Panel
A) Quantity
of 16
Cam Bolts
B) Quantity
of 28
Wood Dowels Dia. 5/16"x1-1/4
C) Quantity
of 16
Cam Locks
D) Quantity
of 16
Cotton Mat
E) Quantity
of 8
Screw Dia.3*10
F) Quantity
of 4
Bolts Dia. 5/32"x5/8"
G)Quantity
o f 2
Knob
H)Quantity
o f 2
Screw Dia.3*10
I)Quantity
o f 4
Bolts Dia.1/4” x1-3/8”
J) Quantity
of 4
Bolts Dia.1/4”*3-1/2” x1-3/8”
L ) Quantity
of 8
Flat Washer Dia. 1/4”*14
M) Quantity
of 8
Spring Washer Dia. 1/4”
N) Quantity
of 1
Allen Wrench
O) Quantity
of 2
Magnet
PL)
Quantity
of 2

Page |
4
PR) Quantity
of 2
Q) Quantity
of 2
Cam Locks
R) Quantity
of 26
Screw Dia.3*14
S) Quantity
of 4
Bolts Dia. 3*x 14
T) Quantity
of 12
Shelf Pin
U) Quantity
of 4
Screw Dia.1/8”*5/8L”
V) Quantity
of 4
Bracket
W)
Quantity
of 2
Plastic chain
X) Quantity
of 4
Anchor
Y) Quantity
of 4
Screw Dia1/8”x1-3/8”L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
SEI Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver, Hammer
(Not Included)

Page |
5
Figure 1
Insert Cam Locks (C) into
corresponding holes on Supports
(2).
Screw Cam Bolts (A) into threaded
holes on Top Panel (1).
Attach Supports (2) to Top Panel
(1) by inserting Cam Bolts (A) and
Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (C) clockwise using
Phillips screwdriver (not included).
Cover cam lock holes with Covers
(D).
Figure 2
Attach Middle Panel (3) to
pre-assembled unit from Figure 1
with Bolts (I), Spring Washers (M),
and Flat Washers (L).
Tighten Bolts (I) with Allen Wrench
(N).
Talus Media Console
Assembly Instructions
C
B

Page |
6
Figure 3
Attach Magnets (O) to
pre-assembled unit from Figure 2
with Screws (S).
Tighten Screws (S) with Phillips
screwdriver (not included)
Figure 4
Insert Cam Locks (C) into
corresponding holes on Panels
(4L/4R/5L/5R).
Screw Cam Bolts (A) into threaded
holes on pre-assembled unit from
Figure 3.
Attach Panels (4L/4R/5L/5R) to
pre-assembled unit from Figure 3
by inserting Cam Bolts (A) and
Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).

Page |
7
Figure 5
Attach Hinges (PL/PR) to Left
Door Panel (7L) with Screws (E).
Attach Iron Plate (Q) to left Door
Panel (7L) with Screw (H).
Attach Handle (G) to Left Door
Panel (7L) with Bolts (F).
Tighten Bolts (F) and Screws
(E/H) with Phillips screwdriver (not
included).
Figure 6
Attach Hinges (PL/PR) to Right
Door Panel (7R) with Screws (E).
Attach Iron Plate (Q) to Right Door
Panel (7R) with Screw (H).
Attach Handle (G) to Right Door
Panel (7R) with Bolts (F).
Tighten Bolts (F) and Screws
(E/H) with Phillips screwdriver (not
included).
PR
QPL
PL
Q
PR

Page |
8
Figure 7
Insert Cam Locks (C) into
corresponding holes on
pre-assembled unit from Figure 4.
Screw Cam Bolts (A) into threaded
holes on Bottom Panel (6).
Attach Doors (7L/7R) to
pre-assembled unit from Figure 4
by inserting upper hinges into
corresponding holes. Lower
hinges will fit into holed on Bottom
Panel (6)
Attach Bottom Panel (6) to
pre-assembled unit from Figure 4
by inserting Cam Bolts (A) and
Wood Dowels (B) into
corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 8
Attach Legs (10) to pre-assembled
unit from Figure 7 with Bolts (J),
Spring Washers (M), and Flat
Washers (L).
Tighten Bolts (J) with Allen
Wrench (N).
Attach Middle Leg (11) to
pre-assembled unit from Figure 7
by hand.
A

Page |
9
Figure 9
Flip over pre-assembled unit from
Figure 8 so that the unit is resting
on its legs.
Attach Back Panel (12) to
pre-assembled unit from Figure 8
with Screws (R).
Tighten Screws (R) with Phillips
screwdriver (not included).
Figure 10
Insert Shelf Pins (T) into desired
pre-drilled holes on pre-assembled
unit from Figure 9.
Place Shelf Panels (8/9) on Shelf
Pins (T).
T

Page |
10
Figure 11
Attach Brackets (V) to back of
pre-assembled unit from Figure 10
using Screws (U).
Tighten Screws (U) using Philips
screwdriver (not included).
Mark two desired locations on
wall.
Drill two 3/16" holes on wall.
Insert Plastic Anchors (X) into the
2 holes on wall, tap with hammer
(not included) as needed
Attach Brackets (V) to wall using
Screws (Y).
Tighten Screws (Y) using Philips
screwdriver (not included).
Figure 12
Move this item close to the wall.
Tie Brackets (V) together with
Plastic Chains (W).
Anti-tipping hardware must be
used for this product to avoid
tipping and injury.
Now you Talus Media Console is
ready for use!
WALL
WALL