Southern Enterprises MS341700TX User manual

Page |
1
MS341700TX
Denver Media Console
Assembly Instructions
For assistance with assembly, contact
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]om
www.seidal.com

Page |
2
Denver Media Console
Parts List
Please review all parts and hardware before disposing of any packaging.
Before beginning assembly, separate each type of hardware. Carefully study the diagrams below and check
that you have all parts indicated. Call Customer Service if missing hardware. Using the incorrect hardware
will cause damage.
A
.
Quantity
of 20
Cam Bolts
B
.
Quantity
of 20
Cam Locks (￠
C. Quantity
of 20
Wood Dowels (￠
8*30)
D. Quantity
of 8
Bolts (￠5/16*2-
1/4”)
E. Quantity
of 8
Spring Washers (￠
5/16”)
F. Quantity
of 8
Flat Washers (￠
5/16”/16mm)
G. Quantity
of 1
Allen Wrench
(5mm)
H. Quantity
of 4
Hinges (￠
1/4”)
I. Quantity
of 18
Screws (￠
3x14mm)
J. Quantity
of 24
Screws (￠8x25mm)
K. Quantity
of 7
Knobs
L. Quantity
of 7
Bolts
M. Quantity
of 2
Magnets
N. Quantity
of 2
Metal Plates

Page |
3
O. Quantity
of 16
Shelf Pins
P.
Quantity
of 34
Screws (￠3x14mm)
Q. Quantity
of 2
PlasticAnchors
R. Quantity
of 2
Screws (￠3.5x19mm)
S. Quantity
of 2
Screws (￠3.5x25mm)
T. Quantity
of 2
Plastic Straps
U. Quantity
of 4
Brackets
V.
Quantity
of 8
Covers
1. Quantity
of 1
Top Panel
2. Quantity
of 1
Bottom Panel
3
.
Quantity
of 4
Left Side Panels
4. Quantity
of 1
Right Side Panel
5. Quantity
of 1
Left Divider Panel
6. Quantity
of 1
Right Divider Panel
7. Quantity
of 2
Cross Bars
8. Quantity
of 1
Door Panel
9. Quantity
of 1
Glass Door Panel
10. Quantity
of 2
Side Adjustable Panels

Page |
4
11. Quantity
of 2
Middle Adjustable Panels
12-1. Quantity
of 1
Top Drawer Front
12-2. Quantity
of 1
Middle Drawer Front
12-3. Quantity
of 1
Bottom Drawer Front
13. Quantity
of 3
Left Drawer Sides
14. Quantity
of 3
Right Drawer Sides
15. Quantity
of 3
Drawer Bottoms
16. Quantity
of 3
Drawer Backs
17. Quantity
of 2
Adjustable Legs
18. Quantity
of 1
Middle Back Panel
19. Quantity
of 1
Right Back Panel
20. Quantity
of 1
Left Back Panel
21. Quantity
of 4
Legs
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
customer service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver (Not Included)

Page |
5
Denver Media Console
Assembly Instructions
Figure 1
Insert Cam Locks (B) into holes
on Cross Bars (7).
Attach Cross Bars (7) to Right Side
Panel (4) and Divider Panel (6) using
Cam Bolts (A) and Wood Dowels (C).
Tighten by rotating Cam Locks (B)
clockwise with Phillips screwdriver.
Figure 2
Insert Cam Locks (B) into holes on Side
Panels (3/4) and Divider Panels (5/6).
Attach Bottom Panel (2) to Side Panels
(3/4) and Divider Panels (5/6) using
Cam Bolts (A) and Wood Dowels (C).
Tighten by rotating cam locks (B)
clockwise with Phillips screwdriver.
Cover cam lock holes with Covers (V).
4
2
6
5
3
4
AC
AC
C
C
A
A
C
C
B
B
B
B
V

Page |
6
Figure 3
Insert Cam Locks (B) into holes on top
side of Side Panels (3/4) and Divider
Panels (5/6).
Attach Top Panel (1) to Side Panels
(3/4) and Divider Panel (5/6) using
Wood Dowels (C) and Cam Bolts (A).
Tighten by rotating Cam Locks (B)
clockwise with Phillips screwdriver.
Cover cam lock holes with Covers (V).
Figure 4
Attach Legs (21) to assembled unit with
Bolts (D), Flat Washers (F), and Spring
Washers (E).
Tighten all bolts with Allen Wrench (G).
Screw Adjustable Foot (17) into bottom
of unit and tighten by hand.
5
3
6
A
A
A
C
A
C
A
A
2
V
2
21
21
17
17
21

Page |
7
Figure 5
Attach Back Panels (19/18/20) to back
of assembled unit in same sequence as
shown with Screws (P).
Tighten screws with Phillips
screwdriver.
Figure 6
Insert Shelf Pins (O) into corresponding
holes on unit.
Place Adjustable Shelves (10/11) onto
Shelf Pins (O).
11
10
11
19
18
20

Page |
8
Figure 7
Connect Magnet (M) on underside of
Top Panel (1) using Screws (P).
Attach Hinges (H) to Door Panel (8)
with Screws (I).
Attach door to unit using attached
Hinges (H) and Screws (I).
Attach Metal Plate (N) to door with
Screw (I).
Attach Knob (K) onto Door Panel (8)
with Bolt (L).
Tighten bolt and screws with Phillips
screwdriver.
Figure 8
Using Screws (P) connect Magnet (M)
to underside of Top Panel (1).
Use Hinges (H) and Screws (I) to attach
Glass Door Panel (9) to unit.
Attach Metal Plate (N) onto inside of
door panel with Screw (I).
Attach Knob (K) to Door Panel (9) with
Bolt (L).
Tighten bolts and screws with Phillips
screwdriver.
LK
8
I
H
1
I
H
1
9

Page |
9
Figure 9
Use Long Screws (J) to connect
Drawer Left/Right Side Panels (13/14)
to Drawer Back Panel (16).
Slide Drawer Bottom Panel (15) into
corresponding grooves on drawer side
and back panels.
Attach Drawer Front Panel (12-1) to
assembled drawer using Long Screws
(J).
Attach Knob (K) onto drawer front with
Bolt (L).
Tighten screws and bolts with Phillips
screwdriver.
Repeat steps to assemble two other
drawers using Drawer Front Panels (12-
2) and (12-3).
Figure 10
Insert Drawers into glides on assembled
unit.
13
14
15
16
J
J
J
12-1 12-2 12-3
12-1

Page |
10
Figure 11
If drawer hits adjoining parts or if drawer
gap is not consistent, you can loosen
screws on side and adjust drawer.
Figure 12
Attach Brackets (U) to Back Panel using
Screws (R).
Tighten Screws (R) using a Philips
screwdriver.
Mark two desired locations on wall. Drill
two 3/16" holes on wall. Insert Plastic
Anchors (Q) into holes on wall (use a
hammer to help).
Attach Brackets (U) to wall using
Screws (S).
Tighten Screws (S) using a Philips
screwdriver.
QUS
QUS
UR

Page |
11
Figure 13
Move unit close to wall and tie all
Brackets (U) with Plastic Straps (T) as
shown.
Anti-tipping hardware must be used for
this product to avoid tipping and injury.
Figure 14
Now your Denver Media Console is
ready to use!
FURNITURE
wall wall
FURNITURE
U
U
U
U

Page |
12
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and
we are not responsible for any damages due to product modification(s). If damages or missing parts are not reported
within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas), Mon-Fri
9am – 4pm CST, or email us at [email protected]. Please ask for customer service representative for issues
involving damages or replacement parts. Please ask for technical assistance representative for any issues with
product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item Store/Website/Catalog
Please indicate color/size/style number
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019

Page |
13
CAUTION
The top shelf is intended for a flat screen television with a maximum overall width of 50”
and supports up to 85 lb.
Each center shelf should not be loaded with more than 20 lb.
Each side shelf should not be loaded with more than 8 lb.
DO OT EXCEED RECOMME DED LOAD. Use with products heavier than the maximum
sizes and weights indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on back panel.
Model: MS341700TX
Denver Media Console
Southern Enterprises, Inc
600 Freeport Parkway, Suite 200
Coppell, Texas, 75019