Southern Enterprises MS664700TX User manual

Page | 1
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]m
www.seidal.com
MS664700TX
Putnam Media Console
Assembly Instructions
PO#:

Page | 2
Putnam Media Console
Assembly Instructions
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Left Side Panel
D.
Quantity
of 1
Right Side Panel
E.
Quantity
of 1
Middle Vertical Panel
F.
Quantity
of 1
Door
G.
Quantity
of 1
Adjustable Shelf Panel
H.
Quantity
of 3
Drawer Front Panel
I.
Quantity
of 3
Drawer Left Panel
J.
Quantity
of 3
Drawer Right Panel
K.
Quantity
of 3
Drawer Back Panel
L.
Quantity
of 3
Drawer Bottom Panel

Page | 3
M.
Quantity
of 1
Upper Back Panel
N.
Quantity
of 1
Lower Back Panel
O.
Quantity
of 4
Leg
1.
Quantity
of 24
Cam Bolt
2.
Quantity
of 24
Cam Lock
3.
Quantity
of 12
Wood Dowel Ø 8 x 30mm
4.
Quantity
of 49
Flat Head Screw
∅
1/8"x
1/2"
5.
Quantity
of 5
Bolt for Handle
∅
5/32"x3/4"
6.
Quantity
of 18
Round Head Screw
Ø 1/8” x 5/8”L
(for Back Panel and Magnet)
7.
Quantity
of 6
Drawer Slide
8.
Quantity
of 3
Handle
9.
Quantity
of 8
Bolt
∅
1/4"x2"L
10.
Quantity
of 1
Allen Wrench
11.
Quantity
of 8
Flat Washer
12.
Quantity
of 8
Spring Washer

Page | 4
13.
Quantity
of 12
Screw
∅
1/8"x1
"
14.
Quantity
of 1
Magnet
15.
Quantity
of 1
Long Handle
16.
Quantity
of 2
Hinge
17.
Quantity
of 1
Magnet Plate
18.
Quantity
of 4
Shelf Support
19.
Quantity
of 4
Bracket
20.
Quantity
of 4
Screw
∅
1/8"x5/8"
21.
Quantity
of 4
Screw
Ø 1/8” x 1-5/8”L
22.
Quantity
of 4
Anchor
23.
Quantity
of 2
Plastic Strap
24.
Quantity
of 20
Cover
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required No.2 Phillips
Screwdriver (Not Included)

Page | 5
Figure 1
Please separate Drawer Slides (7) into
male and female components as shown.
Note: There is a lever located on the
male slide. Push the lever to either
side while pulling in order to detach
the male slide from the female slide.
Figure 2
Screw with fingers to help align screws
before using screwdriver.
Attach Female Drawer Slide (7) to Left
Side Panel (C) using Flat Head Screws
(4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Note: When attaching the female
slides, make sure to insert wood
screws through the first opening
starting from the front, then,
align the openings to the
pre-drilled holes on the panels.
Putnam Media Console
Assembly Instructions
Female Metal Slide
Male Metal Slide
7
7
7
4
7

Page | 6
Figure 3
Attach Female Drawer Slide (7) to
Middle Vertical Panel (E) using Flat
Head Screws (4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Figure
4
Attach Legs (O) to Bottom Panel (B)
using Bolts (9), Flat Washers (11) and
Spring Washers (12) as shown.
Tighten Bolt (9) with Allen Wrench (10).
47
B
O

Page | 7
Figure 5
Screw with fingers to help align cam
bolts before using screwdriver.
Insert Cam Locks (2) into corresponding
holes on Middle Vertical Panel (E), Left
Side Panel (C) and Right Side Panel (D)
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Bottom Panel (B).
Attach Middle Vertical Panel (E), Left
Side Panel (C) and Right Side Panel (D)
to Bottom Panel (B) by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until Middle Vertical
Panel (E), Left Side Panel (C), Right
Side Panel (D) and Bottom Panel (B)
meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Notice: Make sure that all finished
edges are facing towards the front of
the unit.
Figure 6
Attach Magnets (14) to Top Panel (A)
using Round Head Screw (6) as shown.
Tighten Round Head Screw (6) with
Phillips screwdriver.
3
2
2
2
B
C
D
E
6
A
14

Page | 8
Figure 7
Insert Cam Locks (2) into corresponding
holes on assembled unit from Figure 5.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Top Panel (A).
Attach Top Panel (A) to assembled unit
by inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes until
Top Panel (A) and assembled unit meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 8
Attach Back Panels (M/N) to backside of
the unit with Round Head Screws (6).
Tighten Screws (6) with a Phillips
screwdriver.
A
D
E
C
1
3
3
2
2
M
N

Page | 9
Figure 9
Attach Male Drawer Slides (7) to Drawer
Side Panels (I/J) using Flat Head
Screws (4).
Tighten Flat Head Screws (4) with
Phillips screwdriver.
Figure 10
Insert Cam Locks (2) into corresponding
holes on Drawer Side Panels (I/J)
Screw Cam Bolts (1) into corresponding
holes on Drawer Front Panel (H).
Attach Drawer Side Panel (I/J) to
Drawer Front Panel (H) by inserting
Cam Bolts (1) into corresponding holes
until Drawer Side Panel (I/J) and Drawer
Front Panel (H) meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Attach Handle (8) to Drawer Front Panel
(H) using Bolt for Handle (5).
Tighten Bolt (5) with Phillips screwdriver.
Cover Cam Locks with Covers (24) as
shown.
H
2
J
24
24
24
24
77
JI

Page | 10
Figure 11
Insert Drawer Bottom Panel (L) into the
grooves of assembled drawer.
Figure 12
Attach Drawer Back Panel (K) to the
assembled drawer using Screws (13).
Tighten Screws (13) with Phillips
screwdriver.
Repeat Figures 9-12 to assemble the
other drawers.
L
K
13
13
13