Southern Enterprises Andress HO0163A0TX User manual

For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-6 -5096
servi[email protected]
www.seifurniturestore.com
Please do not load more than 30 lb. when desktop is fully raised.
Page 1
HO016 A0TX/HO016 B0TX
Andress Adjustable Height Desk
Assembly Instructions

A. Quantity
of 24
Bolt 1/4”x1/2”L
B. Quantity
of 16
Bolt 1/4”x1-1/4”L
C. Quantity
of 1
Allen Wrench
D. Quantity
of 4
Adjustable lever
E. Quantity
of 2
Screw Φ4.0x1-1/4”L
F. Quantity
of 2
Anchor
G
Quantity
of 4
Bracket
H
Quantity
of 2
Screw Φ4.0x1-5/8”L
I Qu
antity
of 2
Plastic Strap
1
Quantity
of 1
Desktop
2 Quantity
of 1
Side Leg (Left)
3
Quantity
of 1
Side Leg (Right)
4
Quantity
of 1
Shelf Panel
5
Quantity
of 2
Top Rail
6
Quantity
of 1
Bottom Rail
Andress Adjustable Height Desk
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface
like carpet or a blanket. Check that you have all parts indicated. Call customer service if any hardware is missing. Before
beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures. Using the
incorrect hardware will cause damage
.
Page 2

7
Quantity
of 2
Shelf Rail
8 Quantity
of 4
Adjustable Leg
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the surface with rough or
abrasive objects.
For replacement parts or questions, please call SEI
customer service at 1-800-633-5096.
Page 3
Assembly Tool Required:
No.2 Phillips Screwdriver, Hammer, Power Drill
(Not Included)

Figure 1
Attach Adjustable Levels (D)
to Adjustable Legs (8) by
hand.
Figure 2
Attach Adjustable Legs (8) to
Side Legs (1) with Bolts (A) .
Tighten Bolts (A) with Allen
Wrench (C).
Page 3
Andress Adjustable Height Desk
Assembly Instructions

Figure 3
Attach Shelf Rail (7) to Side
Legs (Right) (3) with Bolts
(A).
Tighten Bolts (A) with Allen
Wrench (C).
Figure 4
Line up Side Legs (2/3) and
Rails (5/6).
Page 4

Figure 5
Connect Rails to Side Leg
with Bolts (A).
Tighten Bolts (A) with Allen
Wrench (C).
Figure 6
Attach Shelf (4) to
pre-assembled unit from
Figure 5 with Bolts (B).
Tighten Bolts (B) with Allen
Wrench (C).
Page 5

Figure 7
Attach Brackets (G) to the
Desktop (1) with Screws (H).
Tighten Screws (H) with
Phillips screwdriver (not
included).
Figure 8
Attach pre-assembled unit
from figure 7 to Desktop (1)
with Bolts (B).
Tighten Bolts (B) with Allen
Wrench (C).
Page 6

Figure 8
Mark two desired locations on
the wall and drill two 3/16"
holes.
Insert plastic Anchors (F) into
the holes on wall, tap lightly
with hammer (not included)
as needed.
Figure 9
Attach Brackets (G) to the
wall using Screws (E).
Tighten Screws (E) using
Philips screwdriver.
Page 7

Figure 10
Move this item close to the
wall and tie brackets (H)
together with Plastic Straps
(I).
Note: Anti-tipping hardware
must be used for this
product to avoid tipping
and injury.
Figure 11
Now your Andress Adjustable
Height Desk is ready to use!
To open top, simply lift up.
Guide back down to close.
The top can be adjusted to
four different heights.
Page 8

Figure 12
If the height is not level,
adjust the foot pad by hand.
Figure 13
Change the height by
adjusting the adjustable legs.
Page 9