Sprout OPEN BACK SHELVING User manual

PARTS
OPEN BACK SHELVING
SCHOOL MONTESSORI
ASSEMBLY GUIDE
RECOMMENDED
(2x)
Toe
A
Has Slots
(1x)
Bottom
B
(2x)
D
Sides
(Multiple)
Shelves (one will be used for the top of the unit)
C
REQUIRED
Power Drill
Phillips Screw
F(24x)
Bracket
E(4x)
Rubber MalletWood Glue Two Adults

BEFORE YOU START
*
GLUE
For steps using glue, apply a pea-sized amount to the thin end of slots.
With the tabs orented vertically, apply a pea-sized amount at the top of
each tab (inside its groove). The glue will run down and coat the rest of
the tab during assembly. Apply glue just before connecting pieces.
RECOMMENDED: Wood glue is used to permanently attach the shelving
pieces together, helping make this shelving unit rigid. The glue’s drying
also makes this assembly time-sensitive. To help the process go
smoothly, read all instructions before proceeding.
Using other glue types may aect curing and workablity time.
RECOMMENDED: A rubber mallet can help push
pieces together.
A hammer can also be used with a scrap piece of
wood or a cutting board placed over the surface
being hammered for protection.
1. With the “Groove” facing the “Notch”,
push Tab into Slot until it “pops” in place.
2. Apply force on
part to secure.
GROOVE
NOTCH

ASSEMBLY INSTRUCTIONS
A
B
A
Push tabs on Toes a into slots on bottom b . Tabs and slots must be
lined up correctly or they will not properly tighten. See * for tab
orientation.
1
*
B
A
Turning the part upright, push down on Toes a until the ends are ush
with the ends of Bottom Shelf b . Repeat with second toe.
A
B
2
A
A
B

B
C
C
D
4Press or hammer down Shelves B and Bottom B to tighten until they
make contact with the ground. They will be ush with the underside of
Side D . Parts will be snug.
Remove excess glue from joints with a damp cloth.
If unable to get parts to be ush with each other dissassemble
immediately. Remove glue with a damp cloth and contact Customer
Service.
C
D
BB
3A second adult is recommended to hold shelves in place.
Refer to * for tab orientation. Apply glue to slots on Side D and tabs on
Shelves C and Bottom B . Refer to !! . Pop tabs into corresponding slots.
B
C
D
*
Flat end of Slot
facing up
C
C
D
B

7
Carefully set shelving unit upright. Remove excess glue with damp cloth.
Check that everything is fully tightened.
6To tighten, press or hammer down the second Side D until it makes
contact with the oor. Parts will be snug. Remove excess glue from joints
with a damp cloth.
D
One adult holds steady Side D , Shelves C and Bottom B . Apply glue
to the tabs on C and B and the slots of the other Side D . Pop tabs
into corresponding slots.
5B
B
C
C
D
D
B
C
C
D
Thin end of
Slot facing up
B
C
C
D
D

9
8Tilt the assembled shelf on its back.
Place one of the Brackets E into the corner on the underside of the shelf
like so. The triangular face of the bracket should be against the toe
piece.
10 Using a drill or power screwdriver, install 2 Screws F into the holes on
the triangular face. There are no pre-drilled holes in the wood, so try to
make the screws as straight as possible.
E
F
E
F

12 Repeat for the other 3 corners. Allow glue to set for 1 hour before use.
11 Install 2 more Screws F into the holes on one of the small sides of the
bracket, then the other.
F

INSPIRE SOMEONE
We’d love to see your shelving in
action! If you choose to share a
picture or video with your
new shelving, tag or DM us.
@sprout_kids
SHARE YOUR INSIGHTS
You’re invited to join the
Sprout Advisory Board and
help shape future products.
sprout-kids.com/board
CARE
Use mild
cleaners only
Use a damp
cloth & wipe dry
Learn how to care
for your shelving with
our detailed guide.
sprout-kids.com/cleaning
WARRANTY
Learn about your warranty.
sprout-kids.com/warranty
[phone]
[email protected]
Available M-F 8-4 MST
[phone]
[email protected]
Agents available M-F 8-5 MST
NEED HELP?
WWW.SPROUT-KIDS.COM
PO BOX 1123, PROVO, UT 84601
QUARK ENTERPRISES 2022
DOCUMENT: AI-PIK-LAB_BRAK