Sprout TWIN MONTESSORI Quick setup guide

TWIN MONTESSORI
BIRCH FLOOR BED
ASSEMBLY & USE GUIDE
Freedom of Movement

Thank you for choosing Sprout! As parents ourselves, we
know the care and consideration that goes into selecting
something for your child. We appreciate your trust in
allowing us to be a part of your space! We hope that
these resources will serve your family for years to come.
We believe that children deserve spaces
that help them thrive.
Clark Davis, Founder
Promotes freedom
of movement
Design inspired by the
Montessori Method
Made to grow with
your lile one

We’re Here to Support You
Assembly Instructions
M-F 8-4 MST
[phone]
[email protected]
Included Parts
D E F
End Slats (x2) Phillips
Screws (x8)
Phillips Bit
C
Ends (x2)
B
Slat Roll (x2)
A
Side*(x2)
*Combination of Low, High, or Scoop Sides,
depending on your order
Please reach out to our support team if you need
any assistance along the way!
Baen

Low Position Assembly
1Insert tabs on End c into slots on Side a in the orienta-
tion shown.
2Push down Side a to tighten.
*1. With the “Groove” facing the
“Notch”, push Tab into Slot until it
“pops” in place.
2. Apply force
on part to
secure.
GROOVE
NOTCH
A
NOTE: End c is asymmetrical
and will only assemble in the
correct orientation.
Feet on
boom
Baen closer
to floor
C
A
A
A
A
C
C
Orient
End c as
shown
OPTIONAL: A rubber mallet can help
push pieces together. A hammer can
also be used with a scrap piece of wood
or a cuing board placed over the
surface being hammered for protection.

3Repeat Steps 1 & 2 for opposite End c .
4On a carpeted surface, lift up frame onto Side a , as
shown. Then insert both End Slats d into slots indicated.
This
Slot

6Carefully lay bed back down, then tighten both ends of
the second Side a as shown.
5Place opposite Side a onto tabs on Ends c and End Slats
d . Make sure to “pop” the slots over the tabs on Ends.

8One at a time, insert Phillips Screw e through the holes
in Slat Roll b into the holes in the baen of Sides a .
Tighten down the screws with a screwdriver or a drillgun
using the supplied Phillips Driver f .
7With webbing on top, align the Slat Roll b holes with the
holes in the baen of Side a , as shown.
Webbing

Changing from Low to High Position
10 Using a screwdriver or a drillgun with Phillips Driver f ,
remove all (8) Phillips Screws e . Then remove the two
Slat Rolls b .
9Repeat Steps 7 & 8 with the other Slat Roll b . You are
now done!
Repeat Steps 7 & 8 with the other Slat Roll b . You are now done!

12 On a carpeted surface, lift up the frame onto the tight-
ened Sided a , then remove the Side a that you loosened.
11 Place a piece of wood or hardbound book under the foot
of Side a , as shown, then press down on the top of Ends
c to loosen. Do this for both ends of (1) Side a .
Place piece of
wood here to
loosen this corner Also loosen
this corner
OPTIONAL: A rubber
mallet can help push
pieces apart.
A hammer can also be used
with a scrap piece of wood
or a cuing board placed
over the surface being
hammered for protection.

14 Replace Side a onto the bed frame, making sure to pop
the slots over the tabs on Ends.
13 Carefully move End Slat d from its current slot to the
slot on the opposite side of the baen, as shown. Repeat
for other End Slat d .
To this
slot
Baen

16 Reaach Slat Rolls b onto the top of the baens of Sides
a , as shown, installing per Steps 7-9. You are now done!
15 Carefully lay frame back down as shown, then tighten
both Ends c as shown.

sprout-kids.com/FB
When it comes to your child’s sleep, safety is our top
priority! Since you know your child best, we invite you to
adapt your child’s space based on their unique needs and
abilities. With that in mind, here are some safety
recommendations we encourage you to consider:
Safety Information
There are dierent age recommendations for
items that can be in the bed with your child.
Please scan the QR code below to read more.
With your child’s increased freedom of
movement, be aware of other potential
dangers in your child’s room. You may want
to secure other pieces of furniture to the
walls, move blind cords out of reach, cover all
electrical outlets, and consider general safety
precautions.
For children under 18 months, we recommend
that you do not place the Low Side or Scoop
Side closer than 12” from the wall. Meanwhile,
the High Side should be less than 1.5” or
greater than 12” from the wall.

Making the Transition
Transitioning to a “big kid bed” can be an exciting time for
parents and children alike! Here are some things that may
help as you make the change:
A new bed can be a big change and, for a time, it may
disrupt your child’s rhythm. It can be helpful to make
the changes when there aren't any other major changes
in your home (such as a new baby, moving, etc.).
It can help to keep the rest of their bedtime routine
and bedroom setup as similar as possible so your child
knows what to expect, even if their bed is dierent.
A familiar comfort item like a blanket or stued animal
can help bring a sense of normalcy to your child.
There can be a learning curve for children as they
learn to maneuver around any piece of furniture in the
home. You can observe (by being in the room or with a
baby camera) then guide and model to your child as
they navigate their new bed in their environment.

It took two months before our son actually
slept in his bed. He used to sleep on the floor
next to the door! We transitioned to a floor bed
when we moved into a new apartment, so I
think he was just nervous about all of the
changes. One day, my husband fell asleep on
our son's bed while watching him and from
that point on, Grant has slept in his floor bed!
“
”
- Katie, mother of one
Some of the best things in life can take time, and the
same is true when it comes to learning to sleep
independently. Read about how Grant transitioned to his
new bed:

Proper Care & Use
Designed for Growth
This floor bed is designed to grow with your child. As
they get older, they might feel safer and more
comfortable with the bed in the raised position. Follow
your child’s lead in knowing when they’re ready to
elevate their floor bed; then, follow the assembly
instructions to reassemble the bed in the raised position.
In order to maintain the quality of your product, we
recommend following these basic guidelines:
Abrasive brushes and cleaners will remove the
finish on your product. Use soft cloths only.
A mixture of water and vinegar will clean most
messes. Scrub gently with a soft cloth.
Avoid leing liquid sit on your wooden
product. Wipe it dry to avoid water damage.
Want to dive deeper with additional
Floor Bed resources?
Scan the QR code to learn more!
sprout-kids.com/FB

The Alba Montessori Children’s
Wardrobe allows children to dress and
care for themselves more
independently. A limited number of
weather-appropriate options can be
presented for a less overwhelming
experience for them.
If you’re hoping to increase your child’s
interest in books, adding a Lexico Book
Display Shelf can be a great option.
When presented this way, they can
explore the covers and beer choose
what they want to read.
Thoughtfully preparing a child's environment can
encourage them to explore freely. When a child has a safe
space to test their limits, their confidence can grow and
they can gain a beer understanding of their world. Here
are some other items that you might consider as you
cultivate a prepared environment in your home:
Join the community by following Sprout on Instagram!
We frequently share inspiring and informative
experiences from parents like you, educational tips from
Montessori-trained professionals, and updates about new
products and how they can be used in your home.
A Prepared Environment
Let’s Be Friends
sprout-kids.com[email protected]@sprout_kids
2023 QUARK ENTERPRISES. LLC PO BOX 1123, PROVO, UT 84601 DOCUMENT: PI-FBT_r2