Sprout FBF User manual

With the middle tab partially in its slot, bend the right
tab of Rib F back up to its slot and pop it down in.
3
4
With all three tabs in their slots, straighten Rib F .
Repeat with the other (3) Ribs and the remaining Wide
Slat C and the (2) End Slats D .
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. FBF DOCUMENT: AI-FBF WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2021
Simple. Modern. American Made.
Adult assembly only
Assemble completely
before use
Frustrated?
Need Help?
STOP
Talk to our customer
service agent at:
[phone]
FULL
FLOOR BED
(2) Ends
(2) Sides
(2) Wide Slats
A
E
B
C
C
(2) End Slats
(6) Pine Slats
(4) Ribs
D
D
PARTS
F
2
BEFORE YOU START Put left tab on Rib F into left slot on Wide Slat C .
With the left tab mostly in its slot, bend Rib F over
and pop the middle tab partially down into its slot.
Push tabs of End B into slots on Sides A . Push down
on A to tighten.
Wide Slats C need to be secured in place by sticking
the tabs on C into the corresponding slots on Sides A
that are larger on the top than the bottom. Push down
to tighten.
Whether you use your bed in the Low Position or the
High Position, always arrange the Ribs to be opposite
the Slats from the mattress, as shown.
For children under 18 months, do not place side of
bed closer than 12 inches to a wall.
Pop in tabs
ASSEMBLY INSTRUCTIONS
Must be greater than 12”
C
A
A
A
A
A
B
B
MATTRESS
RIB
MATTRESS
RIB
Low Position
High Position
C
C
C
C
1
F
F
F
F
F
F
5
2 people recommended
for assembly.
F
F

E
E E E E E E
E E E E E
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. FBF DOCUMENT: AI-FBF WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2021
Simple. Modern. American Made.
Adult assembly only
Assemble completely
before use
Frustrated?
Need Help?
STOP
Talk to our customer
service agent at:
[phone]
FULL
FLOOR BED
REMEMBER
Wide Slats C need to be
secured in place by
sticking the tabs on C
into the corresponding
slots on Sides A that are
larger on the top than the
bottom. Push down to
tighten.
For children under 18
months, do not place side
of bed closer than 12
inches to a wall.
Low Position
High Position
2 people recommended
for assembly.
Place all Slats C , D , & E into their respective slots,
as shown.
With help from another adult, install other Side A ,
placing each Slat into its slot in turn, as shown.
Install opposite End B and tighten, just like .
CD
8
To change oor bed from low to high position, bed
must be fully disassembled. To loosen joints, place a
at hard object under Side A and push down on
End B , as shown.
When reassembling keep Ends B oriented with feet
down . The Wide Slats C
that are wider at the top .
Complete to reassemble oor bed in high
position.
B
C
E
Must be greater than 12”
C
C
C
A
A
A
9
11 Steps 1 - 4
C
10 need to be inserted into the
I
II
A
B
A
A
A
B
B
B
B
B
Step 1
(I)
(II)
6
7
A
slots
C CD D
C CD D
Always
against
oor