Sprout LK-6030-5x1 User manual

Simple. Modern. American Made.
Adult assembly only
2 Adults required for assembly
Assemble completely before use
Single Row
Lockers

2
(5) Pegs
with Hole
N
(40) Shelf
Pins
K
RECCOMENDED: A rubber
mallet can help push
pieces together.
A hammer can also be
used with a scrap piece of
wood or a cutting board
placed over the surface
being hammered for
protection.
REQUIRED: Wood glue is
used to permanently
attach the door pegs.
Using other glue types
may aect curing and
workablity time.
REQUIRED: A phillips head
screwdriver.
A drill with a phillips head
driver can also be used,
but is not required.
BEFORE YOU START
(2) Toes
C
(1) Back
D
E
(1) Left Side (1) Right Side
F(4) Vertical
Dividers
G
H
(4) Door (1) End Door
I
(10) Shelves
J
(40) Short
Screws
R
PARTS
(5) Long
Screws
L
(5) Washers
M
(5) Pegs
with Knob
O
(10) Hinge
Clips
P
(10) Hinges
Q
(1) Bottom
A
(1) Top
B
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6030-5x1PAGE 2 OF 8

*When inserting tabs into slots make sure the side with the wider lip on
the tab faces the same direction as the notch in the slot.
NOTCH
WIDE LIP
SLOT TAB
TAB ORIENTATION
PREPARE PARTS
Install Toes C by placing tabs into slots on Bottom A as
shown below. Ensure to orient parts according to
guidelines above. Push to tighten.
1
Frustrated?
Need Help?
STOP Talk to our customer service agent at:
[phone]
A
A
C
C
GLUE
I
Install Pegs K on Back D by inserting Long Screw L
through holes with Washer M , then thread on Peg.
2
III
Install Pegs O on Doors H and I by applying a dot of
glue to bottom of the slot and a thin layer to end of the Peg.
Insert Peg into slot on each door. Wipe o excess glue
with a damp cloth. Ensure to apply glue just before
connecting parts together.
3
N
N
D
D
L
L
M
M
O
O
H
H
I
DOCUMENT: AI-LK-5x1 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 3 OF 8

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6030-5x1PAGE 4 OF 8
Install Hinges Q into slots on Doors H and I by
screwing (2) Short Screws R into pilot holes on Door, as
shown below.
4
Install Hinge Clips P by screwing (2) Short Screws R
into pilot holes indicated on Left Side E and Vertical
Dividers G . Make sure that the Adjustment Screw is
facing forward, as shown.
5
With the help of another adult, insert tabs on Vertical
Dividers G into slots on Top B . Ensure that Dividers
are oriented so that Hinge Clips are on the front-left.
Top should be oriented with slots for Back in the back.
1
ASSEMBLY INSTRUCTIONS
H
H
I
R
R
Q
Q
E
G
R
P
PILOT HOLES
EG
ADJ. SCREW
FACE FORWARD
E
R
P
B
G
TABS FOR BACK
IN BACK
HINGE CLIPS ON
FRONT-LEFT
G
B

Tighten the assembly slightly. Place tabs on Back D
into slots on Top B . Have another adult help steady the
assembly. Ensure the Back is oriented with Pegs on the
front-bottom, as shown below.
2
With the help of another adult, pop Bottom A onto
tabs, starting at one end working down. Ensure slots for
Back D are on the correct side. Tighten slightly.
3
With the help of another adult, carefully tilt assembly
onto Back D . Push down on each corner to lock into
place. When fully tightened, the edges should be ush.
4
D
B
TIGHTEN
SLIGHTLY
TIGHTEN
SLIGHTLY
D
D
D
A
A
D
D
B
DOCUMENT: AI-LK-5x1 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 5 OF 8

6
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-6030-5x1PAGE 6 OF 8
With the help of another adult, pop Sides E and F onto
tabs on each side of the assembly. A book can be placed
under each side to provide more room if necessary.
5
Lock Sides F and E into place by pushing down on
each corner. Edges should be ush when fully
tightened.
6
With the help of another adult, carefully tilt assembly up
onto feet. Insert Shelf Pins N into holes at the desired
height and rest Shelf J on Pins. Each locker should
have (2) Shelves, and each Shelf will use (4) Pins.
7
E
F
FE
E
E
F
F
K
J
J
K

7
DOCUMENT: AI-LK-5x1 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2022 PAGE 7 OF 8
Locker Side
Doors H and I will need to be installed from left to
right. Note that the End Door I has a small circular
groove on the inside face, as depicted below.
1
DOOR ASSEMBLY
H I
I
H
H
H
H
I
SMALL GROOVE
ON INSIDE FACE
I
To attach Door H , carefully attach Hinge Q to Hinge
Clip P by inserting as shown below.
2
Once in position, push the Hinge Q lever and rotate
Hinge ush with the Locker Side until Hinge is locked
into Hinge Clip P .
3
Locker Side
P
P
P
Q
Q
Q
H
H
H Q
P

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. LK-5x1PAGE 8 OF 8
To take Door H o push on lever and rotate Hinge Q
to release it from Hinge Clip P .
4
Adjust Door H to align ush with outer edges of unit
using the Adjustment Screws as shown below.
5
Repeat steps with the rest of the Doors H and I .
*
ADJ. SCREW
SIDE TO SIDE
ADJ. SCREW
UP AND DOWN
H I
Locker Side
P
P
Q
Q
H
H
H
H