Sprout SOSTA BED PLATFORM & LEGS User manual

(2x)
(2x)
(2x)
(2x)
(8x)(12x)
(2x)
PARTS
PLATFORM & LEGS
SOSTA BED
ASSEMBLY GUIDE
Side
A
End
B
Slat Roll
C
Included if you purchased legs
Left Leg
Phillips Screw
D
Note
the “L”
F
Right Leg
1.6” Hex Screw
E
G
REQUIRED
OR
Power
Drill
Phillips
Screwdriver
INCLUDED TOOLS
Hex
Bit
Phillips
Bit
4mm Hex
Wrench

Screw a Phillips Screw into corner of End and Side . Repeat with
each corner.
A
A
B
B
3
Lay out (2x) Sides and (2x) Ends as shown.
A
A
A
B
B
B
1
Starting with one End , fully insert tabs of Sides into slots on Ends
until ush. Repeat with other End .
A
A
A
B
B
B
B
B
2
F
OPTIONAL: A rubber mallet can
help push pieces together.
A hammer can also be used with
a scrap piece of wood or a
cutting board placed over the
surface being hammered for
protection.
Enjoy the best assembly experience
sprout-kids.com/platform
ASSEMBLY VIDEO
F

Flip frame over.
ADDING LEGS
If you didn’t purchase legs, proceed to .
10
5
4
If using a drill, set clutch on drill to LOW SETTING (around 3).
If your drill has two speeds, set it to the SLOW SPEED (1).
A high clutch setting will strip screw heads and render parts useless!
CLUTCH TOO HIGH: If the drill twists dramatically in your hand when
drilling. Lower the clutch setting.
CLUTCH TOO LOW: If the screw does not screw in all the way. Adjust
clutch up by 1 setting and try again.
3
4
2
2
3
3
4
2
1
12
12

Slide the (2x) Left Legs into Sides at opposite corners as shown.
D
6
When adding legs, ensure they point away from the center of the bed.
A
Note the
engraven “L”
D
D
A
A

Repeat steps 6 - 7 with the (2x) Right Legs .
E
8
Flip frame over.
9
E
E
Screw the (4x) 1.6” Hex Screws in the (2x) Left Legs .
D
7G
G
G
D
D
D

10 With webbing face up, align the Slat Roll holes with the Holes in Side
as you lay one of the Slat Rolls onto one half of the bed frame.
C
C
A
Insert the tips of (2x) Phillips Screws through the Slat Roll holes and
vertically into the holes of Side .
A
11 FC
A
A
F
F
C
A
A
C
ADDING SLAT ROLLS

Set the tips of the additional (2x) Phillips Screws through the other Slat
Roll holes and screw them into the holes of Side .
Screw the (2x) Phillips Screws into the holes on the side of the Slat Roll
near the middle of the bed.
C
12 F
F
13 A
F
F
A
A
C
C
F
C
F

14 Repeat steps 10-13 to attach remaining Slat Roll .
AVOID ENTRAPMENT, which can cause serious injury or death, by
placing bed more than 12” away from any wall. Those under the age
of 3 may be at greater risk.
C
MUST BE
GREATER
THAN 12”
C
For additional Safety Regulations and Standards:
sprout-kids.com/sosta/safety
15
If you have questions, reach out to [email protected]
WWW.SPROUT-KIDS.COM
PO BOX 1123, PROVO, UT 84601
QUARK ENTERPRISES 2022
DOCUMENT: AI-SBT-Platform&Legs