Sprout CUBL8 User manual

Simple. Modern. American Made.
Adult assembly only
2 Adults recommended for assembly
Assemble completely before use
Eight Cube
Shelf

Frustrated?
Need Help?
STOP
2
Parts
*
RECOMMENDED: A rubber
mallet can help push
pieces together.
A hammer can also be
used with a scrap piece of
wood or a cutting board
placed over the surface
being hammered for
protection.
When inserting tabs into slots make
sure the side with the wider lip on
the tab faces the same direction as
the notch in the slot.
NOTCH
WIDE LIP
SLOT TAB
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. CUBL8PAGE 2 OF 8
Talk to our customer service agent at:
[phone]
Or email us at:
[email protected]
*Tab will ‘pop’ into slot
when force is applied.
Slot
Tab
Top Shelf
Bottom Shelf
Rib
(4) Feet
Partial Back
A
B
E
H
J
First Side
C
Second Side
D
(3) Vertical Dividers
Horizontal Divider
F
G

ASSEMBLY INSTRUCTIONS
DOCUMENT: AI-CUBL8 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2023 PAGE 3 OF 8
Slide Horizonal Divider F into slots on Vertical
Dividers G , as shown. Set aside.
1F
G
2Pop the tabs on Top Shelf A and Bottom Shelf B
into slots on First Side C . Ensure slots on shelves
are facing inward and forward.
Have a second adult help hold parts in place
through step 6.
AB
C
F
G
G
G
Slots facing
inward &
forward
Slots for
Back
B
C
A
Make sure the side with
the Wide Lip on the tab
faces the same direction
as the Notch in the slot.
slot
tab
NOTCH
WIDE LIP

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. CUBL8PAGE 4 OF 8
3Place divider assembly in between the shelves,
as shown.
4Insert center tab of Back into center slot on Side. Holding
the piece as shown, ex the back and push the dovetail tabs
into the open slots.
E
A
C
B
F
G
E

DOCUMENT: AI-CUBL8 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2023 PAGE 5 OF 8
A
5As one adult holds the back and shelves steady,
insert bottom slots on Second Side D into the tabs
on Top Shelf .
D
6
Insert center tab on Back E into slot on side. Flexing
the Back, push tabs into open slots. Then carefully
insert tabs from all intersectiong parts into slots
on Side D .
E
D
D
E
A
B
D
B
AE

6
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. CUBL8PAGE 6 OF 8
7
8
Carefully tip shelving unit onto its back on a hard oor
and press down on ends of Bottom B and Top A
until ush with sides.
A
B
Screw in the four Legs into the Bottom B until tight,
as shown.
B
H
B
D
A
H
B
D

7
DOCUMENT: AI-CUBL8 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2023 PAGE 7 OF 8
B
B
With the left tab mostly in its slot, bring Rib F up
and pop the middle tab partially into its slot.
10
With the middle tab partially in its slot, bend the right
tab of Rib F back up to its slot and pop it in.
11
With all three tabs in their slots, straighten Rib F .
12
Put left tab on Rib F into left slot on Bottom Shelf B .
B
9J
J
J
J
J
J
B
J
B
J

Simple. Modern. American Made.
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. CUBL8PAGE 8 OF 8