Sprout SFS30 User manual

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. SFS30 DOCUMENT: AI-SFS30 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2021
Simple. Modern. American Made.
Adult assembly only
Assemble completely
before use
2 people recommended
for assembly
Frustrated?
Need Help?
STOP
Talk to our customer
service agent at:
[phone]
Or watch our assembly
video at:
sprout-kids.com/sfs
30-CUBBY
STUDENT FOLIO
STORAGE
(4) Horizontal Divider
(29) Slot Divider
E
B
C
(5) Vertical Divider
(1) Top
(1) Middle Shelf
D
PARTS
F
(1) Bottom
(1) Toe
(1) Left Side
I
(1) Right Side
J
(2) Assembly Jig
K
1
2
4
Push tabs on Toe H into slots on Bottom G , then
tighten per * .
Place Vertical Dividers D into slots of Horizontal
Dividers B , as shown.
3
Place tabs for Bottom G and Middle Shelf F in slots
of Right Side J , as shown. Large slots on Middle
Shelf should be towards front of unit. Insert tabs of
Dividers into slots on Bottom and Middle Shelf, and
tighten Bottom G slightly.
BEFORE YOU START
ASSEMBLY INSTRUCTIONS
(1) Back
A
D
B
H
H
G
G
G
*
NARROW LIP
TAB
SLOT TAB LOCKED INTO SLOT
*Place tab into open slot then lock tabs into the
notch as pictured below.
When fully tightened, the edges should be ush.
A rubber mallet can help push pieces together. A
hammer can also be used with a scrap piece of
wood or a cutting board placed over the surface
being hammered to protect it.
J
Insert tabs of assembled Vertical and Horizontal
Dividers D and B into slots of Right Side J , as
shown. Make sure Vertical Divider tabs are towards
front of unit.
J
DB
B
D
J
I
II
D
B
F
TAB TOWARDS
FRONT
F
J
G
LARGE SLOTS
TOWARDS FRONT
G
NOTCH
WIDE LIP
SLOT TAB
*Orient tabs so the side with the wider lip faces
the same direction as the notch in the slot.
NARROW LIP
RIGHT SIDE
TOP VIEW
SLOT FOR BACK
T
FRONT

7With another adult holding the Assembly Jigs K
steady, slide all Slot Dividers C into their slots on
Middle Shelf F , as shown. Assembly Jigs will help
hold the Slot Dividers in place.
F
F
K
C
With another adult steadying the assembly, insert tabs
of Back A into slots on Right Side J and Bottom G ,
as shown.
Frustrated?
Need Help?
STOP
Talk to our customer
service agent at:
[phone]
Or watch our assembly
video at:
sprout-kids.com/sfs
J
6With another adult holding the assembly steady,
place (1-2) Assembly Jigs K next to Middle Shelf
on the front edge of the unit with slots facing in
towards the Back A .
G
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. SFS30 DOCUMENT: AI-SFS30 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2021
Simple. Modern. American Made.
Adult assembly only
Assemble completely
before use
2 people recommended
for assembly
30-CUBBY
STUDENT FOLIO
STORAGE
8With another adult holding the assembly steady,
insert tabs of Top E into slots on Right Side J , as
shown. Insert tabs of Slot Dividers C and Back A
into slots on Top.
5
*Orient tabs so the side
with the wider lip faces
the same direction as the
notch in the slot.
NOTCH
WIDE LIP
NARROW LIP
SLOT TAB
REMEMBER
TAB
SLOT TAB LOCKED INTO SLOT
*Place tab into open slot
then lock tabs into the
notch as pictured above.
When fully tightened, the
edges should be ush.
A rubber mallet can help
push pieces together. A
hammer can also be used
with a scrap piece of wood
or a cutting board placed
over the surface being
hammered to protect it.
F
K
C
A
E J
J
J
G
A
J
F
K
SLOTS FACING
TOWARDS BACK
A
A
A
C
K
A
C
E

Frustrated?
Need Help?
STOP
Talk to our customer
service agent at:
[phone]
Or watch our assembly
video at:
sprout-kids.com/sfs
Lock tabs on Left Side I and check that all other
tabs are locked and edges are ush. Refer to ! .
10
11
9Place Left Side I onto all tabs, then tighten slightly.
Carefully tilt assembly onto Back A .
Carefully wiggle Assembly Jigs K to remove. With
another adult, carefully tilt unit up onto feet.
K
I
I
A
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. SFS30 DOCUMENT: AI-SFS30 WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2021
Simple. Modern. American Made.
Adult assembly only
Assemble completely
before use
2 people recommended
for assembly
30-CUBBY
STUDENT FOLIO
STORAGE
*Orient tabs so the side
with the wider lip faces
the same direction as the
notch in the slot.
NOTCH
WIDE LIP
NARROW LIP
SLOT TAB
REMEMBER
TAB
SLOT TAB LOCKED INTO SLOT
*Place tab into open slot
then lock tabs into the
notch as pictured above.
When fully tightened, the
edges should be ush.
A rubber mallet can help
push pieces together. A
hammer can also be used
with a scrap piece of wood
or a cutting board placed
over the surface being
hammered to protect it.
I
K
A
I