Sauder August Hill 433851 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-40
Français pg 41-44
Español pg 45-48
Lot # 584536 07/18/22
Purchased: __________________
Corner Entertainment Stand
August Hill Collection | Model 433851
Entertaining what
entertains you.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
3
4
5
6-40
41-44
45-48
49-50
51
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with flat panel televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• Be sure to apply the warning label as instructed later in assembly. The label provides important safety related information.
50 lbs.50 lbs.
433851 www.sauder.com/servicePage 2
19-1/2"19-1/2"
47"47"

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A END (2)
B TOP (1)
C BOTTOM (1)
D SHELF (1)
E SMALL UPRIGHT (1)
F LARGE UPRIGHT (2)
G LARGE ADJUSTABLE SHELF (1)
H SMALL ADJUSTABLE SHELF (2)
J EXTENSION BLOCK (2)
K RIGHT FRONT/LEFT REAR LEG (2)
L LEFT FRONT/RIGHT REAR LEG (2)
M TOP MOLDING (1)
N BOTTOM MOLDING (1)
O UPPER END MOLDING (2)
P LOWER END MOLDING (2)
Q DOOR (2)
BK1 BACK (1)
433851www.sauder.com/service Page 3
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
A
BK1
O
L
K
H
F
Q
J
PO

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
433851 www.sauder.com/servicePage 4
6S BROWN 7/16" LARGE HEAD SCREW - 10 11S BLACK 1/2" FLAT HEAD SCREW - 8
25S BLACK 9/16" PAN HEAD SCREW -4 32S BLACK 9/16" FLAT HEAD SCREW - 8
25E ADJUSTABLE
FOOT - 1
24E FOOT
BASE - 1 8F CAM SCREW - 12
1F HIDDEN CAM - 30 2F CAM DOWEL - 18
APPLIQUE
CARD - 3
123P 1R METAL PIN - 12 1N NAIL - 39 2R RUBBER
SLEEVE - 12
(Refer to Step 35 for proper
location and application)
1L WARNING LABEL - 1
WARNING
For use with televisions weighing 50 lbs.
(22.6 kg) or less. Use with heavier
televisions may result in instability causing
tip over resulting in death or serious injury.
-Never allow children to climb on audio/
video furniture.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
11/18 5 2 4 9 2 8 524928
29M
BUMPER CARD - 2
22K PULL - 2 14H HINGE - 4
15S SILVER 5/8" MACHINE SCREW - 2 14S BROWN 1-1/2" FLAT HEAD SCREW - 4
72S BLACK 2-1/2" LARGE HEAD SCREW - 4 BLACK 1-15/16" FLAT HEAD SCREW - 6 113S

Hardware Usage Guide
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
433851www.sauder.com/service Page 5

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push two HIDDEN CAMS (1F) into the SMALL
UPRIGHT (E). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
433851 www.sauder.com/servicePage 6
E
1
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
(2 used)

Step 2
433851www.sauder.com/service Page 7
E
B
Surface with holes
Angled edge
Angled edge
Surface with
HIDDEN CAMS
Finished edge
1
å Fasten the SMALL UPRIGHT (E) to the TOP (B). Tighten
two HIDDEN CAMS.

BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
one of the ENDS (A) until the shoulders of the SCREWS
rest on the surface of the END.
å NOTE: Do not overtighten the SCREWS.
Step 3
433851 www.sauder.com/servicePage 8
A
Shoulder
Surface with fewer holes

å Slide one of the LOWER END MOLDINGS (P) onto the END (A). Line up the groove in the LOWER END MOLDING over the
head of the SCREWS in the END.
å NOTE: The LOWER END MOLDING is wider than the UPPER END MOLDING.
å NOTE: The MOLDING should be even on both edges of the END.
å NOTE: If the MOLDING comes up o of the SCREWS, remove it and slide it on again.
å Repeat this step for one of the UPPER END MOLDINGS (O).
Step 4
433851www.sauder.com/service Page 9
O
A
P
Shoulder
These edges
should be even.
These edges
should be even.
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the END.
These holes
must be here.
Shoulder

Step 5
433851 www.sauder.com/servicePage 10
A
1F
Arrow
å Carefully turn over the END (A).
å Push eight HIDDEN CAMS (1F) into the END (A).
Do not tighten the HIDDEN CAMS in this step.
1F
Arrow
These holes must be here.
1F Arrow
1