Subaru H001ssC800 User manual

AUDIO VIDEO & NAVIGATION SYSTEM
OWNERS MANUAL
Item QtY DescrIptIon
1 1 AUDIO HEAD UNIT W/LABEL
2 1 AUDIO COVER
3 1 PORTABLE NAVI. DEVICE (PND)
4 1 POUCH FOR PND
5 1 MAIN HARNESS
6 1 SECONDARY HARNESS
7 1 RADIO ANTENNAADAPTER HARNESS
8 1 IPOD HARNESS (DOCK CABLE)
9 1 GPS ANTENNA W/ HARNESS
10 1 GPS ANTENNA SCREW
11 9 CABLE TIE
12 1 GROMMET FOR IPOD
13 1 INSTALLATION SPACER
14 8 M5 BOLT (4 IN KIT, 4 ON RADIO)
15 1 OWNERS MANUAL
16 1 FOAM TAPE
tom tom In-Box KIt
17 1 TOM TOM CD MANUAL
18 1 USB CABLE
19 1 PND BACK COVER
20 1 PND QUICK START GUIDE
ADDItIonAl reQuIreD Items (not In KIt)
21 1 USB/AUX MODULE (PN: H621SAJ220)
: Remove
: Install
: Disconnect
: Connect
: Location of Clip or Screw
: Tighten Torque
: Loosen
:Discard
: Reuse
T
1 “
10MM 1-1/4” (31.7MM)
PUNCH
OR
1-1/4” (31.7MM)
HOLE SAW
NOT IN KIT
113
4
15 20
17
19
18
10
14
12
2
3
8
659
21
7
11
16
SUBARU OF AMERICA PAGE
1/21
DATE
10/22/10
ISSUE
C
FORESTER
installation instructions
PART NUMBER: H001SSC800
DESCRIPTION: FORESTER PND NAVI. AUDIO UNIT
KIT CONTENTS:
TOOLS REQUIRED:
MEANING OF CHARACTERS:

# pArt nAme
1 RADIO TRIM
2 RADIO COVER PLATE & POCKET
3 CENTER CONSOLE
4 GEAR SHIFT TRIM
5 IP TRIM
6 INSTRUMENT PANEL UNIT (IP UNIT)
Disconnect all correspondingnote:
Connectors as you disassemble.
#DescrIptIon
1 GPSANTENNA W/ BRACKET AND HARNESS
2 SECONDARY HARNESS
3 IPOD HARNESS (DOCK CABLE)
4 USB/AUX MODULE (AVAILABLE FROM SUBARU (PN: H621SAJ220)
5 RADIO ANTENNAADAPTER HARNESS
6 MAIN HARNESS
INSTALLATION OVERVIEW
DISASSEMBLY OVERVIEW
SUBARU OF AMERICA PAGE
2/21
DATE
10/22/10
ISSUE
C
FORESTER

Throughout this installationnote:
Before starting this installation make sure that the Vehicle is on a at surface. Failing to • do so could result in damages to the vehicle, to you, and/or others.
Take care of all disassembled vehicle components as they will be reinstalled (• ) into
the vehicle, unless noted ( ) and instructed differently. Use blankets, tape, and other
protective items to avoid scratching components that may/will come in contact with
tools or sharp surfaces.
After or during installation trim (• ) excess from the Cable Ties.
.1-1
.1-2
pre-InstAllI.
Afx the Installation Spacer [13] 1.
to the Audio Unit [1] as shown.
Apply pressure across the entire part to- seat the adhesive.
Do not touch the surfacecAutIon:
of the radio where the Spacer will be
adhered.
Align the edge of thecAutIon:
Spacer with the seam in the Audio
Unit.
2.5”
(2.5 cm)
2”
(5.08 cm)
2”
(5.08 cm)
Cut the Foam Tape [16] provided 2. in the kit as shown.
Do not discard any of the cut Foam-
Tape [16].
SUBARU OF AMERICA PAGE
3/21
DATE
10/22/10
ISSUE
C
FORESTER

.2-1 10MM
.2-3
4. Remove 4 Screws.
Remove the Radio Cover Plate5. and Pocket.
(1) (2)
Remove the Radio Trim.3.
Using the Nylon Pry Tool start by- releasing the bottom clips (1) and (2)
Avoid scratching the trimcAutIon:
and dash panel.
.2-2
DIsAssemBlYII.
Place the Vehicle into Park “P”1. with the Parking Brake set.
Disconnect the Negative Battery2. Terminal.
Note the battery cable position as it will- be reinstalled in the same position.
Do not touch the PositivecAutIon:
Battery Terminal.
SUBARU OF AMERICA PAGE
4/21
DATE
10/22/10
ISSUE
C
FORESTER

.2-5
Dislodge the Emergency Brake6. Trim.
Start by dislodging the front bottom clip- (1).
Remove the Rubber Mat9. (if equipped).
Remove 2 Screws.10.
.2-4
.2-6
Open the Console.7.
Remove any trays.8.
(1)
SUBARU OF AMERICA PAGE
5/21
DATE
10/22/10
ISSUE
C
FORESTER

.2-9
Remove 1 Screw.11.
.2-8
Disconnect the Connectors from13.the bottom of the Console.
Disconnect the Harness Clamp.14.
.2-7
Dislodge the Center Console and12.tilt back.
SUBARU OF AMERICA PAGE
6/21
DATE
10/22/10
ISSUE
C
FORESTER

.2-10
Loosen the Harness Clips and15.dislodge the Vehicle Harness
from the bottom of the Console.
.2-12
Remove the Vehicle’s18.AUX ONLY Module.
Using the Nylon Panel Removal Tool,- dislodge the AUX Module’s 4 clips from
the bottom of the Center Console.
- Discard the Vehicle’sAUX Module.
Avoid scratching theCAUTION:
Center Console.
.2-11
Disconnect the remaining16.Connectors.
Remove the Center Console.17.
Avoid scratching theCAUTION:
Console or Vehicle upon removal.
SUBARU OF AMERICA PAGE
7/21
DATE
10/22/10
ISSUE
C
FORESTER

.2-13
Using the 1 1/4” (31.7mm) punch19.OR hole saw make a hole in the
Center Console as shown.
Return the Center Console to20.the Vehicle leaving it in the tilted
position.
1 ”
.2-15
.2-14
Remove the Gear Shift Trim23.
Lift to release the rear clips, then pull- rearwards to release.
Place the Vehicle back into “P.”24.
Remove the Insert covering the21.Shift Over Ride Button.
Make sure the Vehicle’scAutIon:
Parking Brake is set.
Depress the Shift Override22.Button and move the Shifter
to “D.”
SUBARU OF AMERICA PAGE
8/21
DATE
10/22/10
ISSUE
C
FORESTER

Remove the Instrument Panel25.Trim.
The Instrument Panel Trim isnote:
in 2 parts. Grip both pieces and
pull from the bottom to avoid
separating the parts.
Avoid scratching thecAutIon:
Instrument Trim or Panel.
.2-18
.2-17
Remove any clips that do not28.come off during the Instrument
Panel Trim removal in g. 2-16.
Re-attach them to the Instrument29.Panel Trim.
.2-16
Remove 2 Screws from the26.Instrument Panel.
Disconnect Instrument Panel27.connector from back side and
remove Instrument Panel from
the vehicle starting from the top.
SUBARU OF AMERICA PAGE
9/21
DATE
10/22/10
ISSUE
C
FORESTER

.3-1
Gps AntennA InstAllAtIon.III.
Route the GPS Antenna Harness1.
[9] from the Instrument Panel
Area to the Radio Area.
center consoleIV.
Connect the PND’s Secondary1.
Harness [6] to the Vehicle’s 24
Pin Connector (A: i50).
.3-2
.4-1
Install the GPS Antenna [9] and 2. Bracket using the GPS Antenna
Screw. [10]
- Torque the Screw to 13.2 in•lbf
(1.49 N•m)
Secure GPS Antenna Harness3.
[9] to the Vehicle by inserting the
Harness Clip into the Hole in
the Vehicle from the back side.
That the clip is properlyVerIFY:
seated and secure.
T
SUBARU OF AMERICA PAGE
10/21
DATE
10/22/10
ISSUE
C
FORESTER

Route the USB Connector and2. iPod Harness Connector on the
Secondary Harness [6] downward
through the center console.
Align the Secondary Harness3.
[6] Connectors as shown, and
secure the 24Pin connectors
to the Vehicle Harness with 1
Cable Tie [11].
Locate the Vehicle’s 8 Pin4. Rearview Camera Connector
(i146).
Connect the Secondary5.
Harness’s [6] 8 Pin Connector to
the Vehicle’s Rearview Camera
Connector.
.4-2
.4-3
SUBARU OF AMERICA PAGE
11/21
DATE
10/22/10
ISSUE
C
FORESTER

Route the USB Connector and iPod Harness6.
Connector on the Secondary Harness [6]
as shown.
Secure the Secondary Harness [6] to the 7. Vehicle Harness near the Vehicle Harness
Clamp with 1 Cable Tie [11].
Route the Harnesses [6] as 8. shown.
Secure them to the Vehicle9.
Harness using 1 Cable Ties [11].
.4-4
.4-5
SUBARU OF AMERICA PAGE
12/21
DATE
10/22/10
ISSUE
C
FORESTER

Connect the iPod Harness [8] to 11.iPod Harness Connector on the
Secondary Harness [6].
Apply the 2.5” x 3” (6.35cm x10.
7.62cm) piece of Foam Tape [16]
to the Vehicle’s Bolt.
Secure the iPod Harness Con-12.
nectors [6,8] and the Secondary
Harness [6] to the Vehicle using
1 Cable Tie [11].
.4-6
.4-7
.4-8
SUBARU OF AMERICA PAGE
13/21
DATE
10/22/10
ISSUE
C
FORESTER

Apply the 2” x 3” (5.08cm x14.
7.62cm) piece of Foam Tape [16]
to the Harnesses as shown.
Route the iPod Harness [8] 13.
and the Secondary Harness [6]
as shown.
Route the Harnesses [6, 8] 15.securing them to the Vehicle
Harness with 1 Cable Tie [11].
.4-9
.4-10
.4-11
SUBARU OF AMERICA PAGE
14/21
DATE
10/22/10
ISSUE
C
FORESTER

Secure the Harnesses [6 ,8] to 17.the Vehicle Harness near the
Vehicle Harness Clip with
1 Cable Tie [11].
Continue Routing the Harnesses16.
[6, 8] as shown securing them to
the Vehicle Harness with 2 Cable
Ties [11].
Route the USB Connector on18.
the Secondary Harness [6] and
the Vehicle’s AUX Connector
through the console opening and
connect them to the USB/AUX
Module [21].
.4-12
.4-13
.4-14
SUBARU OF AMERICA PAGE
15/21
DATE
10/22/10
ISSUE
C
FORESTER

Secure the Secondary Harness21.
[6] and the iPod Harness [8]
to the Vehicle Harness with
1 Cable Tie [11].
Applying the cable tie closernote:
or farther to the USB/AUXModule
will adjust how much of the iPod
Harness [8] is accessible.
Route the iPod Harness [8] 19.though the Hole in the Center
Console.
Using the Photo as reference20.make sure the iPod Harness
length is as shown.
That 15” (38.1cm) or moreVerIFY:
of iPod Harness are exposed,
if not check that the harness is
routed properly and without slack.
Install the USB/AUX Module [21] 22.
and the Grommet [12] into the
Center Console.
That the Grommet [12] and VerIFY:
the USB/AUX [21] module seats
properly.
.4-15
.4-16
.4-17
SUBARU OF AMERICA PAGE
16/21
DATE
10/22/10
ISSUE
C
FORESTER

Remove 2 Bolts and the Shipping2.
Brackets from the Audio Unit [1].
Repeat with the other side.-- Discard the Brackets.
- Do not Discard the 4 Bolts.
.5-2
pnD InstAllAtIon &V.
VehIcle re-AssemBlY.
Remove 2 Screws and the1. Bracket from the Radio Cover
Plate and Pocket.
Repeat with the other side.-- Do not discard the Brackets.
- Discard the Radio Cover Plate, Pocket,
and the 4 Screws.
.5-1
Attach the Brackets from the3. Radio Cover Plate to the Head
Unit [1] using 8 bolts [14].
Place the Bracket stamped “R” on the- side of the Radio stamped “R.”
Place the Bracket stamped “L” on the- side of the Radio stamped “L.”
4 Bolts from the PND Kit, and 4 Bolts- from the Audio Unit’s shipping brackets.
- Torque the Bolts to 23.0 ± 5.3 lbf•in
(2.6 ± 0.6 N•m)
T
.5-3
SUBARU OF AMERICA PAGE
17/21
DATE
10/22/10
ISSUE
C
FORESTER

.5-5
Connect the Audio Unit’s Radio5.
Antenna Adapter [7] to the
Vehicle’s 2 Pin Radio Antenna
Connector.
.5-4
Locate the Vehicle’s 2 Pin Radio4. Antenna Connector.
.5-6
Connect the Audio Unit’s Main6.
Harness [5] to the Vehicle’s 14
Pin Connector (D: i87).
SUBARU OF AMERICA PAGE
18/21
DATE
10/22/10
ISSUE
C
FORESTER

.5-8
.5-9
.5-7
Locate the 5 Pin Vehicle7. Microphone Connector (i147)
(if equipped).
Secure the Connector to the8. Vehicle Harness with the 2” x 3”
(5.08cm x 7.62cm) piece of Foam
Tape [16].
Connect the Main Harness [5], 9.
the Secondary Harness’s [6] 3
connectors, the Radio Antenna
Adapter [7], and the GPS Anten-
na [9] to the Audio Unit [1].
Install the Audio Unit [1].10.
Use the 4 screws from the Radio Cover- Plate & Pocket.
SUBARU OF AMERICA PAGE
19/21
DATE
10/22/10
ISSUE
C
FORESTER

Reassemble the Vehicle.11.
That all the components t VerIFY:
together evenly with no uneven
gaps.
Reconnect the Vehicle’s Negative12.Battery Terminal to its original
position.
Do not touch the PositivecAutIon:
Batter Terminal.
.5-10 10MM
SUBARU OF AMERICA PAGE
20/21
DATE
10/22/10
ISSUE
C
FORESTER