Subaru H671SXC200 User manual

INSTALLATION
INSTRUCTIONS
PART NUMBER: H671SXC200
DESCRIPTION: WIRELESS
CHARGER
KIT CONTENTS
Wireless Charging Assembly T- Harness Tie Wrap (Quantity=6)
Foam Tape (Quantity=2) Wireless Charging Information Card
z
TOOLS REQUIRED
Philips Screwdriver Torque Wrench Panel Removal Tool 10mm socket and ratchet
Nipper
PART NUMBER ISSUE DATE SUBARU OF AMERICA 1 OF 13
H671SXC200 REV 01 Nov 27 2019
1
2

VEHICLE PREPARATION
PART NUMBER ISSUE DATE SUBARU OF AMERICA 2 OF 13
H671SXC200 REV 01 Nov 27 2019
3
1. Place vehicle in ACC mode, engage Parking
brake, turn vehicle OFF.
2. Disconnect the negative battery terminal
using a 10mm socket/ratchet. (FIGURE A)
NOTE: If equipped, disconnect eyelet
cable only.
NOTE: DO NOT PROCEED TO THE NEXT
STEP FOR ONE (1) MINUTE TO ALLOW
TIME FOR THE ACCESORY POWER
SUPPLY TO DISCHARGE.
FIGURE A
FIGURE B
FIGURE C
3. Use panel removal tool to pry and push
down on the shift collar. (FIGURE B)
4. Remove shifter knob retention pin by
pushing both sides of the clip forward and
then remove the shifter knob and collar.
(FIGURE C)

VEHICLE PREPARATION, continued
PART NUMBER ISSUE DATE SUBARU OF AMERICA 3 OF 13
H671SXC200 REV 01 Nov 27 2019
3
5. Use panel removal tool to remove rubber
mat and plastic tray and discard. (FIGURE
D)
FIGURE D
FIGURE E
FIGURE F
6. Use panel removal tool to remove console
cover. (FIGURE E)
7. Disconnect console power connection.
(FIGURE F)

VEHICLE PREPARATION, continued
PART NUMBER ISSUE DATE SUBARU OF AMERICA 4 OF 13
H671SXC200 REV 01 Nov 27 2019
3
8. Use panel removal tool to remove rear
console trim cover. (FIGURE G)
FIGURE G
FIGURE H
9. Remove 10mm bolt. Repeat on opposite
side of console. (FIGURE H)

WIRELESS CHARGER INSTALLATION
PART NUMBER ISSUE DATE SUBARU OF AMERICA 5 OF 13
H671SXC200 REV 01 Nov 27 2019
4
1. Remove 4 Philips head screws. Save
screws for reuse. (FIGURE I)
FIGURE I
FIGURE J
FIGURE K
2. Pull back rear console. (FIGURE K)
3. Unplug connector. Remove rear console.
(FIGURE K)

WIRELESS CHARGER IN STALLATION, continue
PART NUMBER ISSUE DATE SUBARU OF AMERICA 6 OF 13
H671SXC200 REV 01 Nov 27 2019
FIGURE M
4
6. Pull back driver side console cover and lay
to the side. (FIGURE N)
4. Release center clips. (FIGURE L)
FIGURE L
FIGURE
N
5. Pull passenger side console cover and
remove. (FIGURE N)

WIRELESS CHARGER INSTALLATION, continue
PART NUMBER ISSUE DATE SUBARU OF AMERICA 7 OF 13
H671SXC200 REV 01 Nov 27 2019
4
9. Route harness up through driver side hole
containing AVH and Xmode harnesses.
Secure to harness. Leave slack for
installation. Place tie wrap as shown.
(FIGURE Q)
FIGURE
Q
8. Plug in wireless charger harness and route
as shown. Place tei wraps as shown.
(FIGURE P)
FIGURE P
FIGURE O
7. Pull back button bar to release clips. Leave
button bar connected. (FIGURE O)

WIRELESS CHARGER INSTALLATION, continue
PART NUMBER ISSUE DATE SUBARU OF AMERICA 8 OF 13
H671SXC200 REV 01 Nov 27 2019
4
FIGURE R
10. Push button panel back into place, ensuring
harness is routed through outer edge.
Wireless charger connector will be facing
driver side.
11. Plug in wireless charger. Clip down.
(FIGURE R)

VEHICLE PARTS RE-INSTALLATION
PART NUMBER ISSUE DATE SUBARU OF AMERICA 9 OF 13
H671SXC200 REV 01 Nov 27 2019
5
1. Reinstall driver side console cover.
(FIGURE S)
FIGURE
S
FIGURE T
FIGURE U
2. Reinstall passenger side console cover.
Make sure center clip is latched. (FIGURE
T)
8. Reconnect connector. (FIGURE U)

VEHICLE PARTS RE-INSTALLATION
PART NUMBER ISSUE DATE SUBARU OF AMERICA 10 OF 13
H671SXC200 REV 01 Nov 27 2019
5
4. Reinstall rear console by sliding it
forward.cover. (FIGURE V)
FIGURE V
FIGURE W
5. Reinstall 4 Philips head screws. (FIGURE
T)