Suncast DBW9936 User manual

0361625© 2021 Suncast Corporation, Batavia, IL
Quality Control Number:
Numéro de contrôle de qualité:
Número de control de calidad:
DBW9936 - Rattan Deck Box
Coffre de terrasse aspect rotin
Arcón para terraza imitación ratán
OWNER’S MANUAL
MANUEL DE L’UTILISATEUR
MANUAL DEL USUARIO

2
• Product not intended for storage of flammable or caustic chemicals.
• Product not intended for use by children. This is not a toy box.
• To avoid risk of suffocation, do not allow children to play inside container.
WARNING
• Do not stand on lid.
• Do not store near excessive heat.
• This product may become susceptible to impact damage in freezing temperatures.
• Exercise caution when moving fully loaded product. This product is not intended for transporting heavy objects. Use as a stationary storage device only.
ATTENTION
• Read instructions prior to assembly. This product contains parts that can be damaged if incorrectly assembled.
• Please follow instructions. Suncast is not responsible for replacing parts damaged due to incorrect assembly.
• Avoid scratching finish. For steps where parts are placed upside down, place parts on a smooth surface to avoid scratching finish. Flatten cardboard
from carton to create a smooth work surface.
•ONCE ASSEMBLED, THE DECK BOX CANNOT BE TAKEN APART WITHOUT BREAKAGE.
BEFORE YOU BEGIN...
This product has a textured exterior. Over time, dust may accumulate in the texture. When combined with moisture, this could encourage the growth of
moss or mold on the product. To maintain the look of your product, we recommend cleaning it each year with mild soap and water. DO NOT use bleach,
ammonia, or other caustic cleaners, and DO NOT use stiff bristle brushes. Failure to perform annual cleaning could result in permanent staining of the
plastic. This is not a manufacturing defect and is not covered under warranty.
MAINTENANCE
To purchase Suncast replacement parts and learn about other Suncast products visit us online or call.
www.suncast.com
24 hours a day, 7 days a week, 365 days a year.
1-800-846-2345 or 1-630-879-2050
SUNCAST PRODUCTS AND REPLACEMENT PARTS
• Phillips Head Screwdriver
• Adjustable Wrench
(Optional: Rubber Mallet / Flat Tip Screwdriver)
NOTE: DO NOT USE POWER SCREWDRIVERS.
TOOLS REQUIRED
Two people are required for assembly.

3
HARDWARE
AB
E
C
DFAH
AG
I
AA
BB
#0102116
Back
x1
#0102112
Bottom
x1
#0102115A
Front
x1
#0280383A
Lid Reinforcing Rod
x1
#0102117A
Side
x2
#0102113
Hinge Pin
x3
#0102111
Latch
x1
1/4" - 10 x 2" Lag Bolt
Threaded Screw
x2
1/4" - 20 x 1-3/4" Bolt
x2
14-10 x 1
1/4" Screw
x2
#0463859C
Spring Shot Set
(2 pcs)
x2
#0102114
Lid
x1
CC
DD
1/4" - 20 Nylon Nut
x2
PARTS
ACTUAL SIZE

Attach (G) to (E) with one (BB) at each end.
4
1
E
BB
G
x2
NOTE: During assembly, position all parts with rattan side out. Place
(B) on flat surface. Snap tabs on (A) into (C).
2
A
C
Snap tabs on (A) into (B).
3
A
B
D
Turn assembly on its side. Snap tabs on assembly into (D).
TIP: If needed, use a rubber mallet to gently tap (D) onto assembly.
FLIP ASSEMBLY AND REPEAT WITH REMAINING (D).
4

5
Insert hinges on (E) assembly into (B).
5
1 11
E
E
B
B
5
At center hinge, insert (F) through both holes in (B) and both holes in (E) until (F) locks in place.
TIP: If needed, use a flat tip screwdriver and a rubber mallet to tap F into fully inserted position.
6
F
E
B
E
B
F