Suncast GLIDETOP BMS4900 User manual

BMS4900 - GLIDETOP"" Shed
OWNER’S MANUAL
MANUEL DE L’UTILISATEUR
MANUAL DEL USUARIO
Quality Control Number:
Numero de contröle de qualite:
Nümero de control de calidad:
© 2011 Suncast Corporation, Batavia, IL 0361167A

BEFORE YOU BEGIN....
* Consult your local authorities for any permits required to construct shed. Prior to the construction of your shed, check with the local
building code official to review any required permits or building limitations.
+ A level and sturdy foundation is required before shed construction can begin. Site preparation information is available on page 3.
* Read instructions thoroughly prior to assembly. This kit contains parts that can be damaged if assembled incorrectly or in the wrong
sequence.
* Please follow instructions. Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly.
* Check for all parts before you begin assembly. Using the provided parts check list on pages 4-5, verify that you have all the parts
required to construct your shed model. COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE UNPACKING ALL
PARTS.
e Avoid scratching finish. For steps where parts are placed upside down, place parts on a smooth flat surface to avoid scratching finish.
4à WARNING
ed not intended for storage of flammable or caustic chemicals.
ed not intended for use by children. This is not a toy box.
is kit contains parts with metal edges. Please be careful when handling.
ATTENTION
* Do not stand, sit, or store items on storage shed roof.
* Heavy articles should not be leaned against the walls, as this may cause panel distortion and permanent damage.
* Treat carefully in extreme temperatures. This product may become susceptible to impact damage in freezing temperatures.
* Do not store near excessive heat.
* Hot items, such as recently used grills, blowtorches, etc., must not be stored in the shed.
* Shed not intended for use in extreme weather conditions.
e Suncast is not responsible for damage caused by weather or misuse.
ASSEMBLY DAY TIPS
* Complete site preparation and foundation construction before unpacking parts and beginning assembly.
* DO NOT attempt to assemble on a day with strong winds.
* DO NOT attempt to assemble on days when temperature is below 32 degrees.
* Make sure you have assistance nearby to lift and secure parts in place.
* Once roof is assembled, a flashlight may be of use when assembling smaller components inside shed.
* DO NOT use a torque wrench or hand drill to tighten provided Easy Bolts. Use provided Easy Bolt Easy Driver tool ONLY.
* For customer convenience, Suncast provides extra hardware. In some cases, there will be small fasteners remaining, after assembly is complete.
MAINTENANCE
* At regular intervals inspect your shed to make sure that assembly integrity has been maintained.
* Repair or replace broken parts immediately.
* Periodically check that the location you have chosen to set your shed is still level.
* Keep roof clean of snow and leaves.
* The shed walls and roof sections have a textured exterior, much like vinyl home siding. Over time, dust may accumulate in the texture. When
combined with moisture, this could encourage the growth of moss or mold on the shed. To maintain the look of your shed, we recommend cleaning
h mild soap and water. DO NOT use bleach, ammonia, or other caustic cleaners, and DO NOT use stiff bristle brushes. Failure to
d result in permanent staining of the plastic. This is not a manufacturing defect and is not covered under warranty.
it each year wi
perform annual cleaning cou
Suncast® Corporation, 701 North Kirk Road, Batavia, Illinois 60510 (Manufacturer) warrants to the original purchaser only that the enclosed product is free
from material and workmanship defects under normal, household use at time of purchase.
This limited warranty does not apply to damage resulting from accident, neglect, misuse, commercial use, alteration, operation not in accordance with
instruction or repairs made or attempted by unauthorized persons.
This limited warranty applies only to the product enclosed and does not apply to accessory parts.
THE MANUFACTURER'S LIABILITY HEREUNDER IS LIMITED SOLELY TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT OR PART AND THE
MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM ANY DEFECT IN
MATERIAL OR WORKMANSHIP OR FROM THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or a limitation of how long an implied warranty lasts, so the
above limitations may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.

SITE PREPARATION AND FOUNDATION CONSTRUCTION
(Materials NOT supplied with Shed Kit)
Note: Site preparation and foundation construction are required for this shed. Placing the shed on the ground without any
type of foundation is not recommended. Without a foundation, settling will cause distortion and damage to the shed. Suncast is
not responsible for replacing parts damaged or property lost due to incorrect assembly.
Any construction materials used outside the provided guidelines will lead to damage to the shed. This damage will cause
catastrophic failure, rendering the unit nonfunctional. Proper steps are required to correctly support the shed.
Note: Complete the site preparation and foundation construction before unpacking parts and beginning assembly.
To prepare your shed site, follow the below steps:
1) Consult your local authorities for building codes and covenants before beginning foundation or erecting shed.
2) Before any digging, check with local utilities to determine location of buried cables, pipes, etc.
3) Prepare the building site:
—The ground should slope away from the foundation area to provide drainage.
-The foundation surface must be flat and level.
4) Decide which type of foundation you want:
-Concrete slab, 4" thick (Recommended)
and/or
Wood platform:
Use exterior grade wood. The wood platform should be set on an even (level) layer. This can consist of crushed rocks or pulverized
concrete or concrete slab. The base layer must be a properly prepared surface to support heavy loads and allow drainage. The
provided plans are sized for the minimum number of cuts to lumber and plywood. Your local retailer can cut the wood to size for you.
5) Anchoring the shed to the prepared foundation:
—To secure the shed to a concrete pad, use masonry fasteners available at your local retailer.
—To secure the shed to a wood platform, use 1/4" x 2" long lag screws with washers. See diagram below for anchoring locations.
-Anchoring the shed is required for stability in windy conditions.
Anchoring floor panel to concrete slab
* Secure shed to concrete pad using masonry fasteners.
* Dimensions allow for shed to fit within the nearest 1" on each side.
Anchoring floor panel to wood platform
* Secure shed to wood platform using 1/4" x 2" lag screws.
Wood Platform Materials List
Oty | Size
1 | 781/4'x 55 1/2" x 3/4" platform base
2 2"x 6" x 78 1/4"
y | 2°x 6252"
9 | 2ºx6'x11º

SUNCAST PRODUCTS AND REPLACEMENT PARTS
To purchase Suncast replacement parts and learn about other Suncast products visit us online or call.
war suneast com T g= 1-800-846-2345 or 1-630-879-2050
Amp, ? hours a day, 7 days a week, ays a year. Mon - Fri 6 am - 8 pm CST
TOOLS REQUIRED
+ Phillips Head Screwdriver o 9
+ Easy Bolt Easy Driver (included in kit) AN
NOTE: DO NOT USE POWER SCREWDRIVERS. Two people are required for assembly.
Names or letters are engraved on parts. (*Unless otherwise noted.)
#0B00095C2 n Ill
*Floor Panel CL
x2
#0B00098C1 #0B00096C1
Front Right Side Panel Rear Right Side Panel
x1 x1
#0B00097C1 H0B00094C1 40B00092C1
Back Panel Rear Left Side Panel Front Left Side Panel
x1 x1 x1
$0B00099C1 $0B00090C1
Left Door Right Door
xi x1

Names or letters are engraved on parts. («Unless otherwise noted.)
=
#0102196C1
Inner Roof Guide
e
#0B00091C2
Rear Roof Panel #0B00093C2
Front Roof Panel #0102197C1
Back to Roof
Retainer
#0102198C2
Outer Roof Clip
x2
#0102195C1 #0102194C1 #0102193C1 #0102192C1
Right Lower Left Upper Door Right Upper Left Lower Door
Door Retainer Relainer Door Retainer Retainer
x1 x1 x1
#0280393
#0440641 * Roof Support
*Roof
Guide
Assembly
xi
#010210202
x1
*Handle
x2
0480301 - Hardware Bag
#10 x 1 inch 48-10 x 3/4 Pan $8 Flat Washer * Easy Driver® Easy Bolt@
Fastener Head Screw x5 x x36
x7 x5
Hardware shown at actual size (*Unless otherwise noted.) Extra hardware provided. Not all are used.