Sundstrom SR 900 User manual

2020-03-18
OI01H-3018 SR 900 1
Operating Instruction
SR 900
Half mask
Revision: 02

General information
Instructions for use for SR 900 should be read before use.
Together with filters from the Sundström filter range in accordance with EN 140:1998. Three sizes S, M and L.
Together with compressed air attachment SR 307, SR 507 and SR 358, SR 359 or SR 360 in accordance with
EN 14594:2005, 3A
Together with powered air unit SR 500 or SR 700 in accordance with EN 12942:1998
Together with Remote filter holder SR 905 according to EN 12083.
When selecting equipment for SR 900 some of the factors that should be taken into account are as follows:
• Type of pollutant
• Concentrations
• Work intensity
• Protection requirements in addition to respiratory protective advice.
Risk analysis should be carried by a person who has suitable training and experience in the area.
2020-03-18
OI01H-3018 SR 900 2

Unpacking SR 900
Packing list:
• Half mask
• Pre-filter
• Pre-filter holder
• Cleaning tissue
• ID-tag
• User instructions
• Storage bag
2020-03-18
OI01H-3018 SR 900 3

1. Filter
2020-03-18
OI01H-3018 SR 900 4
1.1 Check that you have
selected the right filter and
that the use-by date has not
been passed. (Specified on
the filter and is valid provided
that the filter packaging is
unopened.)
1.2 In environments in which
both gases and particles
occur, such as in spray
painting, gas and particle
filters must be combined.
1.3 Place the particle filter on
top of the cartridge. Grasp
both protective elements.
Squeeze hard until you hear
the particle filter snap onto
the gas filter.
1.4 Place a coin it in the
space between the lower lip
of the particle filter and the
small tab moulded into the
side of the gas filter.
Push firmly and twist the coin
until the filter pops off.

2020-03-18
OI01H-3018 SR 900 5
1.5 Fit the filter in the mask
so that the arrows on the filter
point towards the user’s face.
Check that the edge of the
filter is sealed by the filter
holder all around and that the
filter is in the internal groove
of the filter holder all around
1.6 Fit the pre-filter in the pre-
filter.
1.7 Press it into place on the
filter.
1. Filter

2.Donning
2020-03-18
OI01H-3018 SR 900 6
2.1 Remove any hood,
glasses or ear protection from
head.
Put the mask on.
2.2 Take out any twists or
tangles.Adjust the harness.
2.3 Wiggle the respirator until
it fits comfortably.

3. Adjusting the harness
2020-03-18
OI01H-2018 SR 100 7
3.1 Reach behind your neck
and grab the free end of the
harness strap.
3.2 Pull the free end away
from the neck until buckle
pops open.
3.3 Pull on the free end of the
strap until the respirator seats
comfortably on your face.
Use your thumb and
forefinger to squeeze the
buckle shut.
3.4 Wiggle the respirator until
it seats comfortably.

4.Fit check
2020-03-18
OI01H-3018 SR 900 8
4.1 Put the mask on.
4.2 Place the palm of your
hand lightly over the hole on
the pre-filter holder to make it
tight. Take a deep breath and
hold your breath for about 10s.
If the mask is tight, it will be
pressed against your face.
If any leakage is detected:
• check the exhalation membranes, exhalation valves and the gasket,
• adjust the straps of head harness,
• switch to alternative size of the respirator.
Do not use the equipment if you cannot make the mask a tight fit
during the fitting test.
Note that beard growth, scars, or other physical characteristics may
interfere with a proper fit of the respirator.

5. Change the exhalation membrane
2020-03-18
OI01H-3018 SR 900 9
5.1 Remove the protective
cap.
5.2 Prise off the membranes.
5.3 Press the new membrane
onto the pin. Carefully check
that the membrane is in
contact with the membrane
seat all round.
5.4 Press the new protective
cap into place.

6.Change the inhalation membrane 7. Change the head harness
2020-03-18
OI01H-3018 SR 900 10
6.1 Remove the membrane.
6.2 Fasten the new
membrane on the pin.
7.1 Detach the head harness
from the mask.
7.2 Attach the head harness
to the mask.