Sunjoy D-GZ840PST-C1 User manual

Assembly Instructions
D-GZ840PST-C (Black Top) / D-GZ840PST-C1 (Faux Copper Top)
Congratulations on your purchase of our SUNJOY 12’x10’ Hardtop Gazebo. Our clear, easy to
follow, step-by-step instructions will guide you through the assembly process from start to
finish. All you will need is a screwdriver, a hammer and two ladders (not included) whose
height is no less than 2.5 m.
●THIS UNIT IS
WARNING:
HEAVY
●Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the area of the Gazebo construction.
!. Do not assemble this item alone. 4 people are recommended for safe
●Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
●Some parts may contain sharp edges. When assembling and using this product, basic safety
precautions should always be followed to reduce the risk of personal injury and damage to the
product. Please read all instructions before assembly and use.
●Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.
●Assemble on level ground.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step number
in which the part is used
IMPORTANT
Please do not return this product to the store. For technical assistance on assembly or replacement parts.
Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am EST to 8:00 pm PST or fax the replacement part
form which is in the box to 1-740-283-3549 or Email [e-mail] for assistance.

Big top frame A1 2
Big top bar B1 2
Small top support beam C1 4
Small top connector D1 1
Pothook E1 1
Small top roof panel 1 F1 2
Small top roof panel 2 G1 2
Small top cover H1 4
Small top roof cover I1 1
Slanting bar connector F2 4
Beam connector (upper) G2 4
Beam connector (down) H2 4
Short beam 1 K1 2
Short beam 2 K2 2
Long beam1 J1 2
Long beam 2 J2 2
Long pipe 1 L2a 2
Long pipe 2 L2b 2
Short pipe 1 M2a 2
Short pipe 2 M2b 2
Big panel 1 P1 2
Big panel 2 P2 2
Small panel 1 P3 2
Small panel 2 P4 2
Fence Q 8
Parts List

Top slanting bar A3 4
Top beam B3 4
Long side left roof panel 1 C3 2
Long side right roof panel 1 D3 2
Long side left roof panel 2 E3 2
Long side right roof panel 2 F3 2
Long side left roof panel 3 G3 2
Long side right roof panel 3 H3 2
Short side roof panel 1 I3 2
Short side left roof panel 2 J3 2
Short side right roof panel 2 K3 2
Short side left roof panel 3 L3 2
Short side right roof panel 3 M3 2
Big roof panel cover (corner) N3 4
Big roof panel cover (middle) O3 4
Panel wall W 8
Short beam of big roof(short side) (1) W1 2
Short beam of big roof(short side) (2) W2 2
Middle beam of big roof(short side) (1) W3 2
Middle beam of big roof(short side) (2) W4 2
Long beam of big roof(short side) (1) W5 2
Long beam of big roof(short side) (2) W6 2
Short beam of big roof(long side) (1) X1 2
Short beam of big roof(long side) (2) X2 2
Middle beam of big roof(long side) (1) X3 2
Middle beam of big roof(long side) (2) X4 2
Long beam of big roof(long side) (1) X5 2
Long beam of big roof(long side) (2) X6 2

AA M6*15 Bolt 84 PCS
BB M6 Bigger flat washer 250PCS
CC M6*60 Bolt 16PCS
DD M6 Nut 32 PCS
EE M6*35 Bolt 8 PCS
FF M6*15 Bolt 80 PCS
GG M6*70 Bolt 16 PCS
LL M6*35 Bolt 16 PCS
JJ M6*25Bolt 12PCS
HH M6*45Bolt 2 PCS
Z M6 Wrench 2 PCS
Hardware Pack 1

Fig.1: Fix Big top frame A1 and Big top bar B1 by using AA, BB.
Fig.2: Fix Small top support beam C1 and Big top frame A1 by using AA, BB.
Fig.3: Fix Small top support beam C1
and Small top connector D1 by using
DD, BB, CC.
Fig.4: Screw the Pothook E1 into Small
top connector D1.
Fig.5: Screw the Fence Q into Big panel
P1(P2) and Small panel P3(P4) by using
FF, BB.
Fig.6: Fix Big panel P1(P2) and Small panel P3(P4)by using JJ, BB.
Fig7:Attach Beam connector
G2/ H2 to Long beam J1/J2
and Short beam K1/K2 by
using GG, BB, DD.
Fig.8-1: Attach Top slanting bar
A3 and Top beam B3 to Big top
frame A1 by using FF, BB. (Do
step fig8.1 and fig8.2 at the
same time, which is needed 2
pieces of 2M ladder.)
Fig7-1: Fix Panel P1, P2, P3,
P4 and Long beam J2 and
Short Beam I2 by using FF,
LL, BB.
Fig7-2: Fix Slanting bar
connector F2 onto panel
P1, P2, P3, P4 by using FF,
BB.

Fig.8-2: Attach Top slanting bar A3 to Slanting
bar connector F2, Top beam B3 to Beam
connector G2 by using CC, BB, DD. (Do step
fig8.1 and fig8.2 at the same time)
Fig.9: Fix Small top roof panel 1 F1 and Small
top roof panel 2 G1 onto Small top support
beam C1 by using AA, BB.
Fig.10: Fix Small top cover H1 onto Small top
support beam C1 by using EE, BB, then fix
Small top roof cover I1 and Small top connector
D1 by using HH,BB.
Fig.11: Attach Big roof top beam X6 (X5/W5/W6）and Top
slanting bar A3 by using AA, BB.
Fig.12: Attach Big roof top beam X5 to Top beam B3 by
using AA, BB. (Repeat the procedure for X1-X6, W1-W6.)
Fig.13: Attach Big roof top beam X4 to Top slanting bar A3
by using AA, BB (Repeat the procedure for X1-X4,W1-W4.)
Fig.13-1: Attach Long pipe L2a (L2b), Short pipe M2a (M2b) and Top beam B3 by using AA and BB.
Fig.13-2: Attach Long pipe L2a (L2b), Short pipe M2a (M2b) and Top slanting bar A3 by using AA, BB.
AA M6*15 Bolt 44 PCS
BB M6 Bigger washer 60 PCS
EE M6*35 Bolt 16 PCS
KK Φ6X260 Stake 16 PCS
Hardware Pack 2

Fig.14-1: Assemble Long side left roof panel C3 and Long side left roof panel E3 for a whole piece.
Fig.14-2: Attach the assembled Long side left roof panel C3 and Long side left roof panel E3 onto the top
frame by using AA, BB (Repeat the procedure for D3, F3, G3, H3, I3, J3, K3, L3, M3)
Fig.15-1: Insert B
ig roof panel cover
N3 into the hole of Small top support
beam C1.
Fig.15-2: Then attach Big roof panel
cover N3 to Top slanting bar A3 by
using EE, BB, lock Big roof panel co
ver
O3 onto Top beam B3.by using EE,BB
Fig.17: Fasten the whole gazebo to
the ground with Stake KK.
Fig. 16: Attach Panel wall (W) into
tube by using velcro

IMPORTANT
1. Keep all children and pets away from assembly area. Children and pets should be
supervised while gazebo is being assembled.
:
2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction such as
a fence, garage, and house, overhanging branches, laundry lines or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe
assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the gazebo in
the ground. If you wish to secure the pavilion to a wood deck or concrete surface, use 16
anchors suited for these surfaces (anchors not included).
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may
require permits for installation and use. Some special procedures may be valid in your area.
9. While this gazebo is manufactured to withstand strong force winds through only the supplied
ground stakes, securing the gazebo to a deck, concrete patio or a stronger base, in areas
subject to frequent severe weather should be considered.
AA M6*15 Bolt 4 PCS
BB M6 Bigger flat washer 10 PCS
CC M6*60Bolt 2 PCS
DD M6 Nut 3 PCS
EE M6*35 Bolt 2 PCS
FF M6*15 Bolt 4 PCS
GG M6*70 Bolt 2 PCS
LL M6*35 Bolt 2 PCS
JJ M6*25 Bolt 2 PCS
HH M6*45Bolt 1 PCS
Backup Parts

NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather
conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must
be cleaned off regularly. Any damage caused by snow accumulation is not covered by the
warranty.
Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials
and workmanship of your item provided the item is maintained with care and used only for
personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1)
year. We don't reimburse for transportation or delivery costs, or compensate the individual or
any outside party for assembling or disassembling the product.
Items used for commercial, contract, or other non-residential purposes, or items damaged due
to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or
rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for
warranty claims. Warranty is to the original purchaser and is non-transferable. Any
replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow
exclusions or limitations on an implied warranty, the above exclusions and limitations may not
apply. This warranty gives you specific rights, and you may also have other rights, which vary
from state to state.
Exclusions:
Maintenance:
Our iron/steel components for garden accessories and patio items are coated with rust
inhibiting paint that protects it from rusting. However, due to the nature of iron, surface
oxidation (rusting) will occur once these protective coatings are scratched.
This is a natural
process and is not a defect! To minimize this condition, we recommend care when assembling
& handling the product to prevent scratching the paint. Should any scratching or damage occur,
we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily
removed with a very light application of common cooking oil. If surface oxidation (rusting)
occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or
patio and cause damaging stains, which may be difficult to remove. This can be prevented if
measure is taken to keep the product from oxidizing.
mportant: Please do not return this product to the store. For technical assistance on
assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am
EST to 8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or
Email [e-mail] for assistance.
Made in China

GAZEBO NETTING AND CURTAIN ASSEMBLY INSTRUCTIONS
Netting or Curatin is available separatley
KK Plastic ring 104 PCS
Fig.18: Hang Mosquito netting and curtain onto Long pipe 1 L2a (M2a, L2b, M2b) with Plastic ring KK,
keep pipe lay on the inside of curtain.