Sunjoy L-GZ660PST-D User manual

Assembly Instructions
Item #: L-GZ660PST-D
10'x12 Gazebo

IMPORTANT:
Please read and follow all safety statements, warnings, assembly instructions, use & care
directions before attempting to assemble.
WARNING:
1. When installing and assembling your gazebo, it is recommended that 2 or more adults are
involved.
2. This product is intended for outdoor use only and should be placed on flat, horizontal
ground.
3. Ensure enough clearance around the product.
4. Do not use the unit during an electrical storm, as there is a remote chance of getting struck
by lightening.
5. Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury,
possibly even death.
6. Never barbecue under this gazebo or use lanterns that contain naked flames.
7. This package contains small items and plastic bags that should be kept away from children.
8. Ensure that all connectors & poles are firmly secured in position fully. It is important to do so
before use so as to avoid collapsing or damage to the item, which could result in injury.
9. WARNING: Keep all flame and heat sources away from this tent fabric. This tent is made
with fabric that meets CPAI – 84 specifications for flame resistance. It is not fire proof. The
fabric will burn if left in continuous contact with any flame source. The application of any
foreign substance to the tent fabric may render the Flame-resistant properties ineffective.
10. WARNING: Please take down the gazebo during strong wind. The manufacturer or retailer
is not liable for any loss of the product or other items due to the failure to take down the gazebo
during strong wind.
11. Hook maximum weight: 26 lbs.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list. If any part is missing or damaged, do not attempt to assemble the
product.

Small roof connector A1 1
Top connector A2 1
Finial B1 1
Hook B2 1
Small roof bar C1 4
Bar connector (Upper) C2 4
Top bar1 D 4
Top bar 2 E 4
Bar connector (Bottom) E1 8
Crossbeam1 F 4
Crossbeam 2 G 2
Crossbeam 3 H 2
Post 1 I 4
Post 2 J 4
Fence (Middle) K1 4
Fence K2 8
Fence connector 1 K3 4
Fence connector 2 K4 4
Small canopy L 1
Large canopy M 1
Netting N 1
Parts List

Fig.1: Insert fence (K1) and (K2) into post (J)
Fig.2-1: Insert fence (K2) into post (I).
Fig.2-2: Insert fence connector (K3) and (K4) into the hole on the bottom of K2&K1 respectively.

Fig.3: Insert crossbeam (H) and (F) into the post (J).
Fig.4: Insert crossbeam (G) into the post (I).

Fig.5: Insert bar connector (C2) into top connector (A2) then fix the hook (B2) on the top connector (A2)
Fig.6: Insert top bar (D) and (E) into bar connector (C2) (Attention: (E) should be on the right and (D) on the left side.)
Fig.7: Insert the top bar (E) and (D) into connector (E1)
Fig.8: Insert the connector (E1) into post (I) and (J). Put on the large canopy (M). (Do not spread the large canopy.)

AA Ф6*180 Stakes 12 PCS
Hardware Pack
Fig.9-1: Insert small roof bar (C1) into small roof connector (A1), place the small canopy (L) onto the roof. Aligning
the corners and stretching to fit.
Fig.9-2: Attach finial (B1) to the top.
Fig.10: Attach large canopy (M) to the roof, do not unfold now. Insert Small roof bar (C1) into Bar connector (Upper)
(C2), then aligning the corners and stretching to fit the large canopy.
Fig.11: Attach the gazebo securely to the ground. If using on soil or grass, the ground stakes (AA) should be used.

USE & CARE
1. This Gazebo is not a permanent structure and should be disassembled & stored away after
use.
2. Do not repack your gazebo until completely dry.
3. This Gazebo must not be left erect in windy conditions.
WARNINGS
1. Assembly Instructions must be followed.
2. Stakes supplied must be used to hold this gazebo in place when upright.
Fig.12: Using plastic rings (Pre-assembled on the netting) to hang
the netting (N) on crossbeam (H), (F) and (G).