Sunjoy L-PG050PST User manual

Garden Pavilion
ITM./ART. 428992
Assembly Instructions
L-PG050PST
For technical assistance or replacement parts call Sunjoy Monday through Friday from 8:30am to 5:30pm ET.
US: 1-866-578-0101 Canada: 1-866-532-9557 (English and French) or email [e-mail].
NOTE: Please read instructions prior to assembly. It is recommended to use 8 people for assembly.
zWhen assembling and using this product, basic safety precautions should always be followed to reduce the
risk of personal injury and damage to equipment.
zFor outdoor use only.
zKeep instructions for future reference.
zGround stakes are included for use on dirt and grass.
zCheck all bolts for tightness before and during usage.
WARNING: Assemble as per instructions only. Do not alter the construction of the pavilion. Children and pets
should be supervised when they are in area of the pavilion.
Notes before assembly: Permanent installation recommended. For ease of cleaning and safety, do not
assemble less than 6 ft / 1.8 m from any obstruction such as a fence, garage, house, overhanging branches,
laundry line or electrical wires. Install on level ground. To ensure safe use of this pavilion, it may be necessary
to install the pavilion permanently into poured concrete blocks or railroad ties or similar using suitable bolts.
Consult a qualified contractor or representative at your local hardware store or home center.
Please check your local regulations prior to permanently installing this item. Some municipalities have
restrictions and requirements.

NOTE: Gently set parts on a level, non abrasive surface. Verify that there are no missing parts.
Parts List ：Hardwarelist:
Part# Qty. Part Des. Diagram
a 50 M8x20 Bolt
b 62 M8 Acorn Nut
c 152 M8 Flat Washer
d 4 M12 Nut
e 4 M12 Flat Washer
f 16
Φ8X260 Ground
Stake
g 32 M8x16 Bolt
h 8 M8 Nut
W1 2 M8, M12 Wrench
W2 1 M10 Wrench
Part# Qty. Part Des. Diagram
A 4 Bottom Pole
B 4 Upper Pole
C1 2 Side Rail 1
C2 2 Side Rail 2
D1 4 Top Rail 1
D2 4 Top Rail 2
E 8 Top Screen
F1 1 Finial
F2 1 Finial Ball
G 2 Hanging Planter

ASSEMBLY INSTRUCTIONS
PART 1: UPPER DOMEASSEMBLY
Step 1:Assembly Instructions of Circular Rail
\
Step 2:Assembly Instructions of Finial and Dome
Attach Top Rail 1 (D1) to Top Rail 2 (D2) with 4 Bolts (g), Flat washer (c) and Acorn Nut (b). See Fig. 1. The side with
DOWN arrows should face down during assembly. Repeat for the other 6 top rails. Top Rail (D1) and Top Rail (D2) should
alternate until circle is complete.
Screw Finial Ball (F2) to Finial (F1). Place Finial (F1) in the center of the assembled circular rail
and attach it to a Top Screen (E) with a Flat Washer (c) and an Nut (h). See Fig. 2. At the same time,
the Top Screen (E) should be inserted into the assembled Top Rail (D1, D2) with Flat Washer (c) and
Acorn Nut (b) by another person. See. Fig. 3. Repeat for the remaining 7 Top Screens (E). Fully
tighten hardware.
Fig.1
DOWN
Fig.2
Fig. 3

PART 2: POLE AND FENCE ASSEMBLY
NOTE: The Bottom Poles (A) must be orientated so that holes to attach Side Rails (C1 & C2) face each other.
UP
Fig.5
Fig.6
Step 1: Assembly Upper Poles to Dome
( 8 people are needed for this step)
Four people hold the 4 Upper Pole (B) in vertical position and
using 4 people lift assembled dome over 4 poles. Insert the
Upper pole (B) pre-attached bolt into the Top Rail (D2) and
attach with Flat washer (e) and Nut (d). Secure the Upper Pole
(B) with 4 Flat Washers (c) and 4 Bolts (a). See. Fig. 4. Repeat
for remaining 3 Upper Poles (B). Fully tighten hardware.
Step 2: Assembly of Upper Poles to Bottom Poles
( 8 people are needed for this step)
Four people hold the 4 Bottom Poles (A) in vertical direction
and the other 4 people lift the assembled Upper Poles (B)
and the dome. Attach Bottom Pole (A) to Upper Pole (B) with
Bolts (a) and Flat Washer (c). See Fig. 5. Repeat for remaining
3 Bottom Poles (A). Fully tighten hardware.
Step 3: Assembly of Side Rails
Attach Side Rail (C1) to Side Rail (C2) with Bolts (a), Flat
Washers (c) and Acorn Nuts (b). See Fig. 6. Note: The side
with UP arrow should be on the top during assembly. Note
direction of decorative curls are facing opposite of each other.
Fig. 4

PART 2: FINALASSEMBLY
Step 2:Assembly of Ground Stakes and Planters
Attach each Hanging Planter (G)
to a Top Rail (D1). See Fig. 8. Place Ground Stakes (f) through the
base of the Bottom Pole (A) into the
ground on soft surface. See Fig. 9.
Fig.7
Fig.8
Fig.9
Step 1: Attach Side Rails to Poles
Attach Side Rail (C1, C2) to Bottom Pole (A)
with Bolts (a) and Flat Washers (c). See Fig. 7.
Repeat for remaining 3 Bottom Poles (A). Fully
tighten hardware.

E
CARE INSTRUCTIONS
Clean gently with environmentally-friendly soap solution and water using a sponge. Do not use abrasive
materials, wire brushes, chemicals, cleansers or bleach. Do not use a pressure washer. Rinse well. Allow to
air dry.
If there are nicks, chips and scratches, go to your local hardware store or home center and obtain a closest
match touch-up paint suitable for outdoor metal use. Follow instructions that appear on the paint can.
MADE IN CHINA