Sunjoy D-GZ846PCO-J User manual




























IMPORTANT
Thank you very much for choosing Sunjoy Group.
Please take time to read these instructions thoroughly and follow each step carefully for safe and easy
operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. You can call us toll-free at
1-866-578-6569 from 8:00 a.m. EST to 8:00 p.m. PST. You can also send the email to
[email protected] or visit www.sunjoyonline.com to get tech. assistance or to place your
replacement part order form.
Sunjoy D-GZ846PCO-J 14’x14’ Younge Round Gazebo
- Black Top
Owner’s Manual

Cautions:
1. Keep all children and pets away from assembly area. Children and pets should be supervised when
they are in the area of pavilion construction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage,
house, over hanging branches, laundry line or electrical wires.
3. The unit is heavy. Do not assemble alone. Eight people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and use.
6. For outdoor use only. Install on level ground. Stakes are provided to secure the pavilion in the
ground. If you wish to secure the pavilion to a wood deck or concrete surface, you will need to
purchase fasteners appropriate for these surfaces. These are readily available at your local hardware
store or home center.
7. Check all bolts for tightness before and during usage. Do not cook inside the tent.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may require
permits for, or otherwise regulate, installation and use.
9. While this pavilion is manufactured to withstand gale force winds utilizing only the supplied ground
stakes, in areas subject to frequent severe weather, securing the pavilion to a deck, concrete patio or
footings should be considered.
10. Your pavilion has been engineered to accommodate winter snow loads incurred in most areas.
Removal of accumulated snow on the pavilion roof with a roof rake is recommended. In areas that are
regularly subject to blizzard conditions however, removal of the roof panel is suggested. The
assembled roof structure can simply be left intact until warmer conditions return
Assembly Instructions:
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish.
Inside this carton you will find enclosed hardware and parts listed above. Please check the contents
of this package to ensure you have received all of the required parts, and that there is no breakage.
All you will need is a screwdriver, a hammer and two ladders of at least 8 feet (2.5 m) high (not
included).
Parts identification: For ease of identification, all parts are labeled to correspond to the Step number in
which the part is used.





Description No. Qty Picture
Post A8

Base B8

Arch Support C8

Decorative Groove D8

Connector E8

Oblique Beam 1F8
Oblique Beam 2G8
Apron Piece H16
Inner Baffle I8

Small Roof Frame J8

Small Roof Crosspiece
Spot K8
Small Roof Oblique
Beam L8

Small Roof Connector M1

Big Roof Cover Plate N16

Small Roof Cover
Plate O8

Cover Presser P16

Small Roof Cover Q1
Parts List


















Hook R1
Finial S1

Netting and Curtain
Rods Connecting 1 T18
Netting and Curtain
Rods Connecting 2 T28
Netting and Curtain
Rods Connecting 3 T38
Netting and Curtain
Rods U32
AAM6x20HexBolt64PCS
BBM6FlatWasher112PCS
DDM6x15CrossBolt16PCS

EEM6x35HexBolt16PCS

GGM6Nut16PCS

WM6Wrench2PCS
Hardware Pack 1





























Fig.1: Attach Base (B) to Post
(A) by Bolt (AA) and Flat
Washer (BB). Lock tightly.
HardwarePack2
BBM6FlatWasher232PCS
AAM6x20Bolt16PCS

CCM6x15Bolt136PCS

DDM6x15CrossBolt32PCS

EEM6x35HexBolt16PCS

FFM6x55HexBolt8PCS

GGM6Nut24PCS

IIPlasticCover48PCS

Fig.3: Insert another part of Decoration
Gutter Connector (D) into assembled
Decoration Gutter Connector, then use
Bolt (AA) and Flat Washer (BB) to lock
Decoration Gutter Connector (D) and
Post (A) tightly.
Fig.2: Attach Decoration Gutter
Connector (D) to Post (A) by Bolt
(AA) and Flat Washer (BB). Don’t
lock tight.
Fig.5: Attach Cover (E) to Decoration
Gutter Connector (D) by use Screw (DD)
and Flat Washer (BB). Lock them tight.
Fig.4: Attach Decoration Gutter Connector (D)
to the outer connect plate together by use Bolt
(EE), Flat Washer (BB) and Nut (GG). Lock
them tightly.
















































Fig.6-2: There need 2 person to lift the assembled
Big Roof Frame (J) and need 1 more person to
assemble Oblique Beam 1 & 2(F&G).
Fig.6-1: Connect Big Roof Frame (J) by Bolt (EE),
Flat Washer (BB) and Nut (GG). Lock tightly.

Fig.9: Attach Lock Oblique Beam 1
(F) to Big Roof Frame (J) and lock
them tightly by Bolt (CC) and Flat
Washer (BB).
Fig.11: Attach Oblique beam 2
(G) to Decoration Gutter (D)
and lock them tightly by Bolt
(CC) and Flat Washer (BB).
Fig.10: Attach Lock Oblique
Beam 2 (G) to Big Roof Frame (J)
and lock them tightly by Bolt (CC)
and Flat Washer (BB).
Fig.8: Attach Oblique Beam 1(F) to
Post (A) and lock them tightly by
Bolt (CC) and Flat Washer (BB).
Fig.12: Attach Big Roof Beam (H)
to Oblique Beam 1&2 (F&G) and
lock them tightly by Screw (DD)
and Flat Washer (BB).
Fig.7: Connect Oblique Beam 1
(F) and Decoration Gutter (D) by
Bolt (CC) and Flat Washer (BB).


























Fig.13: Lock Small Roof Inclined
Beam (L) and Big Roof Frame (J)
tightly by Bolt (CC) and Flat
Washer (BB). Dot lock tight.
Fig.14: Attach Small Roof Connector (M) to Small Roof Inclined Beam
(L) and lock them tightly by Screw (FF), Flat Washer (BB) and Nut
(GG). Screw Hook (R) on Small Roof Connector (M).
After complete this step, then fasten all bolts on Fig 13 & Fig 14.
Fig.15: Fix Small Roof Baffe
(K) as shown above. Lock them
tightly by Bolt (CC) and Flat
Washer (BB).

Fig.16: Attach Small Roof
Inclined Beam (L) to Small Roof
Baffe(K) and lock them tightly by
Bolt (CC) and Flat Washer (BB).
Fig.17: Insert Arc Support Bar (C) to
the ecoration ring of Post (A), lock
them tightly by use Bolt (CC), Flat
Washer (BB). Then use Plastic
Cover(II) to cover the Bolt (CC).
Fig.18: Lock Netting and Curtain Rods
Connecting 1 (T1) and Arch support (C) to
Decoration Gutter (D) by using Bolt (AA),
Flat Washer (BB). Then use Plastic Cover
(II) to cover the Bolt (AA).
Fig.19: Fix Inner baffle (I), Netting and Curtain Rods
Connecting 2&3 (T2&T3) and Decoration Gutter (D)
together by using Bolt (CC) and Flat Washer (BB).
Then use Plastic Cover (II) to cover the Bolt (CC).
























HardwarePack3
BBM6FlatWasher40PCS
DDM6x15CrossBolt40PCS

HHΦ8x260 Stake16PCS
Fig.22: Attach Small Roof
Cover (Q), Finial (S) and Small
Roof Connector (M) together as
shown above.

Fig.20: Connect two Small
Roof Sheet (O) in order as
shown in above and insert the
last Small Roof Sheet into the
slot of first Small Roof Sheet.
Fig.21: Lock Small Roof Sheet
(O) to Small roof crosspiece
spot (K) by using Bolt (DD) and
Flat Washer (BB).



















Fig.24: Connect two Big Roof
Sheet (N) in order as shown
above. And insert the last Big
Roof Sheet into the slot of first
Big Roof Sheet.
Fig.25: Fix Big Roof Sheet (N) by Cover
Presser (P). Then lock Cover Presser
(P) with Decoration Gutter (D) tightly by
Screw (DD) and Flat Washer (BB).
Fig.23: Insert one side of Big
Roof Sheet (N) under Big Roof
Frame(J).
AAM6x20HexBolt4PCS
BBM6FlatWasher12PCS
CCM6x15HexBolt8PCS

DDM6x15CrossBolt5PCS

EEM6x35HexBolt2PCS

FFM6x55CrossBolt1PCS

GGM6Nut2PCS

IIPlasticCover4PCS

Back up Hardware
Fig.26: Fix the gazebo on the groud by Stake (HH).
Fig.27: Insert one end of the Netting and Curtain Rods (U) which has snap hook hole into Netting and
Curtain Rods connecting 2 (T2), make sure it is insert totally. (The same way to insert Netting and
Curtain Rods connecting 3 (T3) with Netting and Curtain Rods (U).)
Fig.28: Counter pull the inserted Netting and Curtain Rods (U) to the snap hook fix area, then make it’s
another side insert into Netting and Curtain Rods connecting 1 (T1) .

Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that
protects it from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once
these protective coatings are scratched. This is not a defect and thus not covered by the warranty.
To minimize this condition, we recommend care when assembling & handling the product to prevent
scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up
with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of common cooking oil. If surface
oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping
on to deck or patio and caused damaging stains, which may be difficult to remove. This can be
prevented if the above-mentioned measures are taken to keep the product from oxidizing.
Limited Manufacturer’s Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal,
residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1) year.
We don't reimburse for transportation or delivery costs, or compensate the individual or any outside
party for assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts
of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware
is not covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is
to the original purchaser and is non-transferable. Any replacement of warranted items will be in the
original style and color, or a similar style and color if the original is unavailable or has been
discontinued. As some states do not allow exclusions or limitations on an implied warranty, the above
exclusions and limitations may not apply. This warranty gives you specific rights, and you may also
have other rights, which vary from state to state.
Made in China