Sunjoy A202010800 User manual

ITEM No.:A202010800
Country of Origin: China Production Number: xxxxxxxxxx
WE HAVE YOU IN MIND, LET US SERVE YOU!
Questions? Issues?
CONTACT US
24 hours / 7 days a week
www.sunjoyonline.com
1-(866)-578-6569
[email protected]

2
inForMaTion
BEForE You BEGin
Before beginning assembly, make sure all parts are present. Compare parts received with the “Parts List.” If any part
is missing or damaged, do NOT attempt to assemble the product. Please read and understand this entire manual
before attempting to assemble, operate or install this product.
GEnEraL inForMaTion
Your new bench is made from the finest materials available. It should provide many years of enjoyment with
minimal care.
Keep your bench clean and apply a coat of wax a few times a year. For best results, clean the bench with warm
soapy water and use an outdoor furniture wax. If you use furniture covers, always make sure the bench is clean
and completely dry before covering as mold may form in dark, wet places. Check the bolts on your bench regularly
to make sure they are tight.
To provide a rust free product this bench is made of Cast Aluminum which is a relatively soft material. Be careful
not to over tighten your hardware. Stripped hardware is not covered under the manufacturer’s warranty. The
weight limit for this bench is 225 lbs.
SaFETY inForMaTion
WarninG
DO NOT stand or allow children to stand on the assembled product. DO NOT tighten bolts completely until
instructed to do so. After nal alignment, make sure all nuts and bolts are securely fastened. NEVER use a power
tool to assemble or tighten your furniture. Perform periodic checks to make sure the hardware is secure and tighten
if needed.
cauTion
READ all instruction before beginning assembly. Failure to do so may result in faulty assembly and potential injury.
Assemble the item on a soft, non-abrasive surface such as a carpet or cardboard to avoid damaging the item.

ParTS LiST
3
Label Description Qty
ATable Top 1
BLeg 3
CRound Leg Support 1
DBackrest 2
C
D
A
B
E
F
ESeat 2
FChair Leg 8
Part Number
Label Description Qty
GM6x35mm Bolt 7
HWasher/Spring Washer
/nut/Plastic cap (M8) 24
IWasher/Spring Washer
/nut/Plastic cap (M6) 7
JM8x30mm Stud 4
KWrench M6/M8 1
Ladjustable
Foot(Pre-Installed) 11
Part Number
P002100353
P005400434
P002200234
P001500065
P001600199
P005400435
H020010016
H090020002
R070010009
H100010015
H100010016
H010080013

aSSEMBLY
4
PrEParaTion
Before beginning assembly, be sure to empty contents of carton and make sure all parts are present.
Place all parts on a soft, level surface for assembly. Estimated Assembly Time: 60 Minutes | DO NOT over tighten hardware!
ASSEMBLY Chair
Fit the Backrest Dto the Seat Eby inserting the
. prefixed studs into the two holes on the seat. Bolt
together using Washers/Spring washers/ Nuts H.Tighten
the nut using the Wrench K.
Hardware Used:4 - Washer, Spring Washer, Nut 8mm
1
1
ASSEMBLY Chair
Turn the unit upside down. Fix the Chair legs Fto the
. Seat Eby fitting the prefixed studs and into the holes in
the top of the legs.Bolt together using Washers/Spring
washers/Nuts H.Tighten the nut using the WrenchK.
Hardware Used:16 - Washer, Spring Washer, Nut 8mm
2
2

aSSEMBLY
5
3
ASSEMBLY TABLE
Attach the roundleg support Cto the three legs
. using Bolts G,washers/Spring washers/and nuts I
Tighten all nuts.
Hardware Used:6-Bolt 6X35mm
6- Washer, Spring Washer, Nut 6mm
4
4
ASSEMBLY TABLE
Lay the table top Aupside down on an even soft clean
. surface.Fix the studs Jinto the table top,then fit the
three table legs Bover the fixed studsJand bolt in
position using washers/Spring washers/and nuts H.DO NOT
OVER TIGHTEN.
Hardware Used:3- Stud 8x30mm
3- Washer, Spring Washer, Nut 8mm
3

aSSEMBLY
6
Tighten ALL nuts on table and chairs using Wrench K. DO NOT OVER TIGHTEN. Adjust the
pre-installed rubber Feet Luntil the Bistro Set is level with the ground.At last,cover all
Nuts with Plastic Caps I/H.Now your Bistro Set is ready for use!
5

Beforeusing,cleantheChaircompletelywithasoftdrytowel.Whennotinuse,wipefreeofanydirtorlooseobjects,
wash with a mild solutionof soap and water; rinse thoroughly anddrycompletely.Donotusestrongdetergentor
abrasivecleaners.Overtimenutsandboltscanloosen.Occasionally,checknutsandbolts,re‐tightenifnecessary.
SUNJOYGroupwarrantstotheoriginalpurchaserthatthisitemisfreefromdefectsinworkmanshipandmaterialsfor
aperiodof6monthsfromthedateofpurchase,providedtheitemwasfactory‐sealedatthetimeofpurchaseandis
maintainedwithcareandusedonlyforpersonal,residentialpurposes.Shouldanymanufacturingdefectarisewithin
this warranty period, SUNJOY Group will replace (at our option) any defective merchandise or parts uponproof of
purchase;however,transportationanddeliverycosts,aswellaspaymentstoathirdpartyforassemblyordisassembly
of the item, remain the responsibility of the purchaser. A purchaser of an "open box," previously‐returned, or
"clearance"item,as wellasoriginal purchasersoutside ofthewarrantyperiod,mayobtainreplacementpartsfrom
SUNJOYGroupforproductsincurrentproduction,atnominalcost.
Items used for commercial, contract, or other non‐residential purposes, or items damaged due to acts of nature,
vandalism,misuse,orimproperassemblyarenotcovered.Corrosionorrustingofhardwareisnotcovered.Proofof
purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is
non‐transferable.Anyreplacementofwarranteditemswillbeintheoriginalstyleandcolor,orasimilarstyleand
coloriftheoriginalisunavailableorhasbeendiscontinued.Assomestatesdonotallowexclusionsorlimitationsonan
impliedwarranty,theaboveexclusionsandlimitationsmaynotapply.Thiswarrantygivesyouspecificrights,andyou
mayalsohaveotherrights,whichvaryfromstatetostate. 
Care and Maintenance
Limited Manufacturer’s Warranty
Exclusions:
7