Sunjoy L-GZ682PCO-N User manual

3September2014 1
OUTDOOR GAZEBO
ITM./ART. 853330
MODEL#L-GZ682PCO-N
ASSEMBLY INSTRUCTIONS
IMPORTANT: RETAIN FOR FUTURE REFERENCE. READ CAREFULLY.
Please check with your local governing authority / local municipal codes regarding installation of
structures before assembly.
Tools required (not included): Phillips screwdriver, hammer, 2 ladders that are at least 2.4 m / 7.8 ft in height, cordless
drill, socket, ratchet set (Metric), socket adapter and socket driver, carpenter’s level.
WARNING:
Check to ensure all parts are present prior to assembly.
This unit is heavy! 5 adults are needed for safe assembly ---- Never assemble this alone!
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of
the gazebo construction.
Keep assembly area more than 1.8 m / 5.9 ft from any obstruction such as fence, garage, and house, overhanging branches,
laundry line or electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and
use.
For outdoor use only. Check all bolts for tightness before use and periodically check and tighten bolts as necessary.
Assemble this unit on firm, level ground or hard surface only. Ensure the unit is level after final assembly.
Protect parts during assembly by laying them on a non-abrasive surface such as blankets or cardboard.
IMPORTANT
Please do not return this product to the store. For technical assistance or replacement parts call Sunjoy from 8:30 AM to 4:30 PM
Eastern Time at the following: 1-866-578-0101 (English, French & Spanish inUS) or e-mail: [e-mail].

3September2014 2
Parts List
PART
# DESCRIPTION QTY LINE DRAWING OF PART
A1 Gutter 1 (Long) 2
A2 Gutter 2 (Short) 6
A3 Corner Cover 1
(Outside) 8
B1 Post 1 2
B2 Post 2 2
B3 Post 3 4
C Fence 2
D Porcelain Tile Top 2
E1 Bracket (Slate Top) 4
E2 Connector 1 (Slate
Top) 2
F Bar 1 (Large Roof) 8
G1 Roof Panel 1 (Large
Roof, Long & Upper) 2
G2 Roof Panel 2 (Large
Roof, Long & Lower) 2
G3 Roof panel 3 (Large
Roof, Short & Upper) 6
PART
# DESCRIPTION QTY LINE DRAWING OF PART
G4 Roof Panel 4 (Large
Roof, Short & Lower) 6
H Connector 2 (Slanting
Bar) 8
I Bar Cover (Large
Roof) 8
J1 Lock Plate 1 16
J2 Lock Plate 2 16
K1 Roof Frame (Large
Roof) 1
L Bar 2 ( Small Roof) 8
M1 Roof Panel 5 (Small
Roof, Long) 2
M2 Roof Panel 6 (Small
Roof, Short) 6
N Connector 3 (Small
Roof) 1
O Hook 1
P Bar Cover (Small
Roof) 8
Q Corner Cover 2
(Inside) 8
R Connector Cover
(Small Roof) 1

3September2014 3
Hardware Packet for Step 1
PART # DESCRIPTION QTY LINE DRAWING
AA M6 x 15mm bolt 16
BB M6 washer 152
CC M6 x20mm bolt 48
DD M6 x 35mm bolt 32
EE M6 x 55mm bolt 16
FF M6 x 65mm bolt 16
GG M6 nut 24
Z M6 wrench 2

3September2014 4
Fig.1:Attach Connector 2 (H) to Post (B1, B2, B3) with bolt (EE), washer (BB) and nut (GG). Do not tighten them at this step.
Fig.2: Attach Gutter (A2) to Post (B1, B2) with bolts (CC, DD) and washer (BB), fix Connector 2 (H) with Gutter (A2) with
bolts (CC, DD) and washer (BB). Do not tighten them at this step.
Fig.3:Attach Fence (C) to Post (B1, B2) with bolt (EE) and washer (BB). Make sure screw holes in Fence (C) are facing out and
at the top.
Fig.4: Attach Gutter (A1) to Post (B3) with bolt (CC) and washer (BB) and fix Connector 2 (H) with Gutter (A1) with bolt (DD)
Fig.5: Attach Gutter (A2) to Post (B3) with bolt (CC) and washer (BB) and fix Connector 2 (H) with Gutter (A2) with bolt (DD)
and washer (BB). Do not tighten them at this step.
Fig.5-1:Attach Gutter (A2) to Post (B2) with bolt (CC) and washer (BB) and fix Connector 2 (H) with Gutter (A2) with bolt
(DD) and washer (BB). Fasten all the bolts and washers including those that are not fastened at the steps above. Once all of the
gutters are installed, adjust the alignment of the gutters to the posts so that each post and gutter are equal distance apart and that
each post is plumb and vertically aligned with the gutters.

3September2014 5
Hardware Packet for Step 2
PART # DESCRIPTION QTY LINE DRAWING
AA M6 x 15mm bolt 8
BB M6 washer 24
FF M6 x65mm bolt 8
GG M6 nut 8
Fig.6:Attach Bar 1 (F) to Connector 2 (H) with bolt (FF), nut (GG) and washer (BB).
Fig.7:Attach Bar 1(F) to Roof Frame (K1) with bolt (AA) and washer (BB)

3September2014 6
Hardware Packet for Step 3
PART # DESCRIPTION QTY LINE DRAWING
AA M6 x 15mm bolt 16
BB M6 washer 178
CC M6 x20mm bolt 2
OO M6 x 45mm bolt 16
HH M6 x 15mm bolt 128
II M6 x 25mm bolt 16
Fig.8: Secure Bar 2 (L) and Roof Frame (K1) with bolt (AA) and washer (BB).
Fig.9: Screw Hook (O) upon Connector 3 (N).
Fig.10:Attach Bar 2 (L) to Connector 3 (N) with bolt (FF), nut (GG) and washer (BB) and fasten them.

3September2014 7
Fig.11: Place Roof Panel 5 (M1) and Roof Panel 6 (M2) on Bar 2 (L) and secure them with bolt (HH) and washer (BB).
Fig.12: Place Bar Cover (P) between the assembled roof panels and secure them on Bar 2 (L) with bolt (OO) and washer
(BB).
Fig.13: Place Connector Cover (R) on Bar Cover (P) between and fasten them with bolt (CC) and washer (BB).
Fig.14: Place Roof Panel 1 (G1) and Roof Panel 3 (G3) on the upper end of Bar 1 (F) and secure them with bolt (AA) and
washer (BB), bolt (HH) and washer (BB).
Fig.15: Place Roof Panel 2 (G2) and Roof Panel 4 (G4) on the lower end of Bar 1 (F) and secure them with bolt (HH) and
washer (BB).
Fig.16: Secure Roof Panel 2 (G2) and Roof Panel (G4) on Connector 2 (H).

3September2014 8
Hardware Packet for Step 4
PART # DESCRIPTION QTY LINE DRAWING
AA M6 x 15mm bolt 20
BB M6 washer 20
MM 8 x 260mm stake 16
JJ M10 x 70mm expansion bolt 16
Fig.17: Attach Corner Cover 1 (A3) to the assembled Gutter (A1, A2) with bolt (II) and washer (BB). Adjust the
Corner Cover by holding the cover in place to align with the gutters and tightening the bolts. You can make additional
adjustments by loosening the bolts that are attached to the gutters at the post tops (see Fig.4).
Fig.18: Put Bar Cover (I) between these large roof panels and secure them with bolt (HH) and washer (BB).
Fig.19: Attach Corner Cover 2 (Q) to the assembled Gutter (A1,A2) with bolt (HH) and washer (BB).

3September2014 9
CARE INSTRUCTIONS
Clean gently with a sponge using environmentally-friendly soap solution and water. Do not use abrasive materials, wire
brushes, chemicals, cleansers or bleach. Do not use a pressure washer. Rinse well. Allow to air dry.
If there are nicks, chips or scratches, go to your local hardware store or home center and obtain a closest match touch-up
paint suitable for outdoor metal use. Follow instructions that appear on the paint can.
SPECIFICATIONS:
Resists winds up to 50 mph when firmly anchored using stakes to the ground.
Resists winds up to 63 mph when firmly anchored using expansion bolts into a suitable concrete base.
Roof can withstand up to 249 kg / 549 lbs weight load.
Maximum load for the center hook: 39.9 kg / 87 lbs.
MADE IN CHINA
Fig.20: Attach Bracket (E1) to Fence (C) with bolt (AA) and washer (BB).
Fig.21:Attach Connector 1 (E2) to Porcelain Tile Top (D) and Fence (C) respectively with bolt (AA) and washer (BB).
Fig.22: Secure all Posts (B1, B2, B3) to the ground with stake (MM) if it is soft surface.
Fig.23: Secure all Posts (B1, B2, B3) with expansion bolt (JJ) if installed on a concrete base.
E