Sunjoy L-GZ043PST-7L User manual

1
Assembly Instructions
ITEM#L-GZ043PST-7L
10’x12’ Leaf Gazebo
IMPORTANT:
Please read and follow all safety statements, warnings, assembly instructions, use & care directions, before
attempting to assemble.
WARNINGS:
1. Assembly Instructions must be followed.
2. Pegs supplied must be used to hold this gazebo in place when upright.
3. Warranty does not cover damage due to extreme weather conditions.
4. Do not use candles, matches or open flames of any kind in or near a tent.
5. Do not cook inside the tent.
6. Build campfires downwind and several meters away from a tent and be sure to fully extinguish campfires before
leaving a campsite or before retiring for the night.
7. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use battery-operated
lanterns whenever possible.
8. Do not refuel lamps, heaters or stoves inside a tent.

2
9. Extinguish or turn off all lanterns before going to sleep.
10.Do not smoke in a tent.
11.Do not store flammable liquids inside a tent
12. KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent is made of
flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous contact with a flame source.
Parts List
AA M6X35 Bolt 20PCS
BB M6 Flat Washer 31PCS
CC M6 Nut 8PCS
EE M6x20 Bolt 3PCS
GG ￠6 x180 Peg 16PCS
DD M6 Wrench 2PCS
TT Plastic Tie 54PCS
Hardware Pack
AA M6X35 Bolt 2PCS
BB M6 Flat Washer 4PCS
CC M6 Nut 1PC
TT Plastic Tie 2PCS
PP Touch up paint 1PC
Spare Hardware

3
A Panel 1 4
B Panel 2 4
C Pole 1 2
D Pole 2 2
E Pole 3 2
F Pole 4 2
G Top Pole 4
H Hanging Pole 4
I Corner connector 4
J Center connector 1
K Long side support pole 2
L Canopy 1
M Top canopy 1
N Bug netting 1
O Short side support pole 2
P Hook 1
Q Privacy Panel 1
R Pipe for Privacy Panel 2
S Pipe Connector 1

4
Tools required: ladder, hammer (not included)
ASSEMBLY STEPS:
Step 1: Frame Assembly
1.1 Use bolt (AA) and flat washer (BB) to joint panel 1(A,) and panel 2(B) ( Fig.1)
1.2 Insert pole (D) into pole (C) and pole (F) into pole (E) (Fig. 2)
1.3 Connect pole (C,D,E,F) with Panel (A,B) to set up a quadrate frame (Fig.3 )
ABA
B
A
B
A
A
B
B
AB
C
D
E
F
C
D
F
E

5
R
Fig.9
A
B
A(B)
R
S
R
F
Fig.8
A
B
Step 2: Top Assembly (Note: Ladder needs to be used in step 2.4 and 2.5)
2.1 Insert corner connector (I) into the holes at the top corner of panel (A,B) (Fig. 5)
2.2 Insert hook (P) into center connector (J) (Fig.4)
2.3 Assemble hanging pole (H) and top pole (G) (Fig.5)
2.4 Connect one end of the top pole (G) with center connector (J) (Fig 6). The other end of the hanging pole is fixed
to the corner connector with bolt (AA), flat washer (BB) and nut (CC) (Fig. 5) 2.5 Insert one end of the long side
support pole (K) and short side
support pole (O) into the center
connector (Fig.6). The other end
is fixed to pole (D) and pole (F)
with bolt (AA), flat washer (BB)
and nut (CC) (Fig. 7)
2.6. Connect pipe connector (S)
with pole (F) by using bolt (EE)
and flat washer (BB); Insert one
end of pipe (R) into pipe
connector (S) (Fig.8); Fix the
other end of Pipe (R) to Panel
(A,B) with bolt (EE) and flat
washer (BB) (Fig.9)
After Step 1 and Step 2, use wrench (DD) to tighten all hardware. Note: do not tighten them excessively
A
B
A
B
Fig.6
Fig.7
A
A
B
B
AB

6
L
M
N
TT
Q
GG
Q
Fig.10
Fig.11
Fig.12
Step 3: Canopy, Bug Netting and Privacy Panel Assembly
Note: Ladder is needed to assemble canopy
3.1. Assemble the canopy (L) on top frame (do not tighten), fully assemble top canopy (M) on top pole (G). Tie the
bug netting between the canopy (L) and top canopy (M) and then fully stretch canopy (L).
3.2. Use plastic ties (TT) to fix the bug netting (N) on panel (A,B)and poles(C,D,E,F) (Fig.11)
Please note: the long side and short side of the bug netting (N) should fit the long side and short side of the
frame accordingly.
3.3. Use plastic ties (TT) to fix privacy panel (Q) on pipe (R) (Fig.12)
3.4. Use peg (GG) to fix the gazebo on ground (Fig.10)
Now your gazebo is ready for use.

7
Note: Please keep these extra parts since they are not covered in product warranty. Use these extra parts to fasten
the electrical cord with the top beam if a light is used.
USE & CARE:
1. This gazebo is not a permanent structure and should be disassembled & stored away after use.
2. Do not repack your gazebo until completely dry.
3. This gazebo must be assembled by two adults or more.
4. This gazebo must not be left erect in windy conditions.
5. Loading limit of the hook is 33 lbs.
6. Loading limit of the ring is 25 lbs
7. Steel components for garden accessories and furniture are treated with rust inhibiting paint that protects
them from rust. However, due to the nature of steel, surface oxidation (rusting) will occur if this protective
coating is scratched. This is a natural process. To minimize this condition, it is recommended that care be
taken when assembling and handling the product in order to prevent the paint from being scratched. If
scratching or damage occurs, it is recommended that the area be touched-up immediately with rust inhibiting
paint, which is included in the package. Surface rust can be removed easily using a very light application of
common cooking oil. If surface oxidation (rusting) occurs and no measures are taken to correct it, the oxidation
may start dripping onto the deck or patio, which may cause damaging stains that may be difficult to remove.
Extra Parts
XX Electrical cord tie 10 PCS