Sunjoy 88-0424-4 User manual

COLONIAL GAZEBO
88-0424-4
Assembly Instructions

Identification of parts In order to facilitate identification, all parts are labelled
according to the step in which they are used.
step1 step1
step2
step3
step4

(2 pcs) 1A Short rail (left) (2 pcs) 1B Short rail (right)
(2 pcs) 1C Long rail (left) (2 pcs) 1D Long rail (right)
(2 pcs) 1E Short launder (left) (2 pcs) 1F Short launder
(right)
(2 pcs) 1G Long launder (left) (2 pcs) 1H Long launder
(right)
(4 pcs) 1I Middle launder
connector (4 pcs) 1L Corner launder connector
(2 pcs) 1M Corner mandrill
connector (2 pcs) 1N
Corner
mandrill
connector
(1 pc) 2A Top connector (1 pc) 2B Pothook
(4 pcs) 2C Long slanting bar (2 pcs) 2E Short top bar
(2 pcs) 2F Long top bar (1 pc) 2G Large canopy
(1 pc) 3
A
Small top
connector (4 pcs) 3B Small top pole
(1 pc) 3C Small top finial (1 pc) 3D Small canopy
(4 pcs) 4A Post (4 pcs) 4B Post baffle
(4 pcs)4C Post base (4pcs) 4D Post top
(1 pc)4E Wall (1 pc) 4F Mosquito ne
t
(8pcs) CC
M6×10mmscrew
(pre-installed)
(TBZ00306010HQ
)
(8pcs) EE
M6
nut(pre-installe
d)
(TBZ20106HQ)
Parts List

24pieces (AA) M6×35mm screw
(TBZ00306035HQ)
48 pieces (BB) M6mm washer
(TBZ10806HQ)
24 pieces (DD) M6×15mm screw
(TBZ00306015HQ)
2 pieces (WW) M6 Wrench
Hardware Pack 1
For step3
4 pieces (AA) M6×35mm screw
(TBZ00306035HQ)
4 pieces (BB) M6mm washer
(TBZ10806HQ)
4 pieces (EE)M6 nut
(TBZ20106HQ)
Hardware Pack 2
For step4
48 pieces (HH) M6×20mm screw
(TBZ00306020HQ)
8 pieces (DD) M6×15mm screw
(TBZ00306015HQ)
48 pieces (BB) M6mm washer
(TBZ10806HQ)
16 i
(GG) ￠8X180 peg
(TBZ10608180HQ)
Hardware Pack 3

STEP1: Screen，Gutter
Fig.1
Fig. 1
Fig. 2
Attach part 1A to part 1E using bolts AA and
washers BB. Repeat this procedure for the
other launders and rails, as shown in Fig. 1.
Unscrew the pre-installed bolts (CC) on part 1I,
and attach the 1A & 1E and 1B & 1F
assemblies to part 1I using washers BB and
bolts DD. Attach part 1A to part 1B using
washers BB and bolts DD, as shown in Fig. 2.
Tighten the pre-installed bolts on part 1I
securely.
1L
1F
1C
Fig. 3
Insert part 1L into one side of the launder (1F),
and then insert parts 1F and 1B into
the other side of parts 1G and 1C.
Secure parts 1B, 1C, and 1F together
and secure part 1G to part 1M using
bolts DD and washers BB, as shown
in Fig. 3.
Hardware Pack 1

STEP 2: Large canopy
Fig.7
2E
Attach hook 2B to part 2A, as shown in Fig. 4. Insert the other end of part 2C
into part 1N, as shown in Fig. 6.
CC 1H
2E
Fig. 7
1E
1F
2F
CC CC
Fig. 8

Unscrew the pre-installed bolt CC, nut EE on part 1I,
secure 1G& 1H assembly and 2F together using CC,
EE. as shown in Fig.7
Unscrew the pre-installed bolt
CC, nut EE on part 1I, secure
1E& 1F assembly and 2F
together using CC, EE. as
shown in Fig. 4&8. Place the
large canopy onto the assembled
top frame.
STEP 3: Small canopy
3B
3B
3B
Fig. 9 Fig. 10
Insert part 3B into part 3A, and secure part 3B, part 2C, and part 2C1 together using bolts AA,
washers BB, and nuts EE to form the small top frame, as shown in Fig. 9 and Fig. 10.

Fig. 11
Place the small canopy (3D) onto the
small top frame, and secure it
in place by tightening the finial
(3C) onto the bolt on the top of
part 3A, as shown in Fig. 11. Fit
2G into its final position
STEP 4: Posts, Mosquito Net, Wall
Fig.12
4C

Fig. 13
Attach post top and post base to post using the screws. as shown in
Fig. 12.1 & 12.2
Lift the complete top assembly, and attach the posts (4A) to
the rails using bolts HH and washers BB, as shown in Fig. 12.
Note: this step may require 4 or more people.
Attach part 4B to part 4D, and
secure them together using bolts
DD, as shown in Fig. 13.
Fig. 14
Anchor the gazebo to the ground
using the pegs (GG), as shown in
Fig. 14.
Hang the mosquito net (4F) on the gazebo. Tie the laces on the wall (4E) to the appropriate pole and rail,
depending on the direction of the sunlight.
BB
4C
4A
BB
4D
4A
BB
4D

1. WARNING
1. In order to reduce the risk of personal injury and damage to equipment, basic safety precautions
should always be followed when assembling and using this product. Read all instructions
carefully before assembly and use.
2. Some parts may contain sharp edges. Wear protective gloves if necessary. In order to ensure
safe assembly, it is recommended that this product be assembled by at least two people.
3. Keep children and pets away from the assembly area.
4. Begin the assembly at least 6 feet away from any obstruction, such as a fence, garage, house,
overhanging branches, laundry line, or electrical wires.
5. Install this gazebo on level ground. This gazebo cannot be permanently stacked or attached to a
concrete floor or platform. This gazebo is intended for decorative and sunshade purposes only,
and is not designed to withstand harsh weather, including high winds, rain, and snow.
6. Verify that all nuts and bolts are tightly secured before and during use.
Care & Maintenance
Steel components for garden accessories and furniture are treated with rust inhibiting paint that protects
them from rust. However, due to the nature of steel, surface oxidation (rusting) will occur if this protective
coating is scratched. This is a natural process. To minimize this condition, it is recommended that care
be taken when assembling and handling the product in order to prevent the paint from being scratched.
If scratching or damage occurs, it is recommended that the area be touched-up immediately with rust
inhibiting paint, which is included in the package. Surface rust can be removed easily using a very light
application of common cooking oil. If surface oxidation (rusting) occurs and no measures are taken to
correct it, the oxidation may start dripping onto the deck or patio, which may cause damaging stains that
may be difficult to remove.
If you are within or beyond the return policy that most stores have, and need tech. assistance or replacement parts, please call
Sunjoy Industries at 1(866) 578-6569 from 8:30 am to 5:30 pm eastern standard time or e-mail to [e-mail] or
fax your parts replacement order form together with the purchase receipt to 1 [phone] for assistance. For French service, pls.
call1-888-477-8426 or fax at 450-477-9326.