Sunjoy G-GZ032PWI User manual

88-1356-0
Assembly InstructionSun Gazebo G-GZ032PWI
Important :
1. Please read entire instruction sheet before assembling.
2. Some parts may contain sharp edges. Wear protective gloves if necessary.
3. Not for use by children. Keep children & pets away from the gazebo when assembling.
4. This unit is heavy! Do not assemble without a helper.
5. Begin assembly not less than 6 feet from any obstruction such as fence, garage, house, overhanging
branches, laundry line or electrical wires.
6. Install on level ground. This gazebo cannot be permanently staked or attached to concrete floor or
platform. This gazebo is intended for decorative and sunshade purposes only and is not meant to
withstand inclement weather including high winds, rain and snow. Gazebo fabric is water resistant, not
water proof and may leak during exposure to precipitation.
7. Keep all flame and heat sources away from gazebo material. Gazebo fabric is not fire proof. The fabric
will burn if left in continuous contact with any flame source.
8. Check to make sure you have all parts described in “Part List” section below prior to assemble. If any
parts missed or damaged, please do not return product to the store. For expedited replacement parts
order, completed “PARTS REPLACEMENT ORDER FORM” that put in carton and fax it to [phone]
or send via e-mail at [e-mail].
Part List :
No.
Part
Qty.
A
Center fitting
1
B
Lintel
4
C
Screen
4
D
Pole (88.4”)
4
E
Pole (65.2”)
4
F
Bolt (0.24” x 0.98”)
(TBZ00106025HQ)
8
G
Washer
(0.24”)(TBZ10406HQ)
48
H
Nut (0.24”)
(TBZ20106HQ)
16
I
Plastic nut cap
(TBZ11306HS)
16
J
Bolt (0.24” x 0.63”)
(TBZ00106016HQ)
16
K
Canopy
1
L
Stake
(TBZ107080180HQ)
8
M
Bracket (pre-assembled)
8
N
Bolt (0.24” x 1.26”)
(TBZ00106032HQ)
8
Required tools: Adjustable wrench

Assembly Instructions
Step 1 Check all parts and hardware listed on the parts list. Lay them on a clear and level surface prior to
assembly. Ideally, the gazebo frame should be set up in its desired location to avoid moving it after assembly.
Step 2 Attach lintel (B) to screen (C) and fasten using bolt (J) and washer (G). Make sure not to cross-thread
bolts (see Fig. 1). Do not overtighten fasteners.
Step 3 Attach poles (D) to centre fitting (A) and fasten using bolt (F), washer (G) and nut (H) (see Fig.2).
Step 4 Attach poles (E) to centre fittings (A) and fasten using bolt (F), washer (G) and nut (H) (see Fig. 2).
Step 5 Attach poles (D) to screen (C) and fasten using bolt (N), washer (G) and nut (H) (see Fig. 3).
Step 6 Attach poles (E) to lintel (B) and fasten using bolt (N), washer (G) and nut (H) (see Fig. 3).
Step 7 Put canopy (K) over the frame, fit canopy corners to the top part of poles (D), and then fit canopy
rim onto the top part of poles (E).
Step 8 Tighten all hardware and put plastic nut caps (I) on nuts (H).
Step 9 Pull up the brackets (M).
Step 10 Secure the gazebo to the ground with stakes (L).

Warning
This gazebo is not meant to withstand extreme weather, such as: moderate to high winds, continued
exposure to ice, or freezing conditions. We recommend removing your canopy if heavy rain, snow, or big
wind. Do not leave the gazebo out in the winter unprotected. Water gets in the metalwork and will freeze
and expand causing ruptures.
This unit is heavy. Do not assemble this item alone.
Limited Warranty
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal, residential
purposes.
The item is warranted to be free from defects in material or workmanship for a period of 6months. We
don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for
assembling or disassembling the product.