Sunjoy MALIBU 10'X12' GAZEBO User manual

DO NOT RETURN TO
RETAILER
IF YOU HAVE ANY QUESTIONS OR CONCERNS
PLEASE VISIT OUR WEBSITE AT:
www.sunjoyonline.com
OR TOLL FREE AT:
1-866-578-6569
8:00 AM EST to 8:00 PM PST
Production Number：2018xxxx
SUNJOY GROUP INTERNATIONAL PTE LTD
619 Slack Street
Steubenville, Ohio 43952USA

WARNING:
1. Assembly Instructions must be followed.
2. Gazebo must be secured / anchored when fully assembled.
SAFETY INFORMATION:
Please read and understand this entire manual before attempting to assemble or install the product.
When installing and assembling the item, it is recommended four or more adults are involved.
This product is intended for outdoor use only and should be placed on flat, horizontal ground.
Ensure enough clearance around the product.
Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightning.
Do not climb on top of the item. Falling off it can result in serious injury, possibly even death.
Never barbecue under this item or use lanterns that contain open flames.
This package contains small items and plastic bags that should be kept away from children.
Ensure all connectors and poles are firmly secured in position. It is important to do so before use to avoid
collapsing or damage to the item, which could also result in injury.
Center hook’s maximum weight capacity is 26 lbs.
WARNING:
Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that meets CPAI-84
specifications for flame resistance. It is not fire proof. The fabric will burn if left in continuous contact with any
flame source. The application of any foreign substance to the tent fabric may render the flame-resistant
properties ineffective. Remove the roof during severe weather conditions such as sustained strong winds,
hurricanes, tropical downpours and snow. The manufacturer or retailer is not liable for any loss of the product
or other items due to the failure to take down the item during any inclement weather.
PREPARATION:
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents
list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
ASSEMBLY INSTRUCTIONS
ITEM# L-GZ215PST-B
SKU# 145569
10'X12' MALIBU GAZEBO

Post
Part NO. QTY
ImageCS NO.Description
A
P11154B01108
P11654A01108
P11542A01108
P11076C01108
P11077C01108
P11078C01108
P11079C01108
P10740A01108
P10741A01108
P10835A01108
P11892A01108
P10316B01108
P10489A01108
P10490A01108
P12164A01108
P12165A01108
P10120B01108
P10121B01108
P10122B01108
P10123B01108
P10124B01108
P10255A01108
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
1
4
4
4
4
4
4
Post base B
Base cover C
D
E
F
G
H1
H2
J
K
L
Short crossbeam (1)
Short crossbeam (2)
Long crossbeam (1)
Long crossbeam (2)
Corner bar connector 1
Corner bar connector 2
Middle beam connector
Corner connect bar
Big top beam
Short side beam M
Long side beam N
Long netting bar O
Short netting bar P
Big top frame connector 1 Q1
Big top frame connector 2 Q2
Big top frame long beam R
Big top frame short beam S
Small top connector T
Small top beam U
Parts List

ASSEMBLY INSTRUCTIONS:
AA 24 PCS
BB 72 PCS
CC 40 PCS
DD 8 PCS
ZZ
M6x15 screw
M6 flat washer
M6x15 bolt
M6x25 screw
M6 wrench 1 PC
Hardware Pack 1
Small canopy V 1
Large canopy W 1
Mosquito netting Y 1
Hook Z 1
Part NO.
Part NO.
QTY
QTY
Image
Image
CS NO.
CS NO.
P00157B06005
H09015C11
H19001C11
H02015C11
H09025C11
H00001C12
P00158B06005
P00334B01902
P12601C01108
Description
Description

Fig.4: Connect the netting bar O (P) to the crossbeam D (E, F, G) with screw (AA) and washer (BB).
Fig.5: Connect the middle beam connector (J) to the crossbeam E,D (G,F) with bolt (CC) and washer (BB).
Fig.6: Connect the corner connect bar (K) to the crossbeam D (E, F, G) with screw (DD) and washer (BB).
Fig.1: Fit the base cover (C) to the post (A), connect the post base (B) to Post (A) with screw (AA) and
washer (BB).
Fig.2: Connect the crossbeam F (D) and G (E) with bolt (CC) and washer (BB), tighten the bolts both side
and top.
Fig.3: Connect assembled crossbeam to the post (A) with bolt (CC) and washer (BB), both side and top.
AA 8 PCS H09015C11
H19001C11
H09035C11
H14001C11
BB 16 PCS
EE 4 PCS
FF
M6x15 screw
M6 flat washer
M6x35 screw
M6 nut 4 PCS
Hardware Pack 2
Part NO.
QTY
ImageCS NO.Description

`
Fig.10: Insert another end of the big top beam (L) to the corner bar connector (H1 & H2).
Fig.11: Connect another end of short (long) side beam M (N) to the middle beam connector (J) by screw (EE),
washer (BB) and nut (FF).
Fig.12: Screw the hook (Z) to the small top connector (T). Insert the small top beam (U) to the small top connector
(T). Attach the small canopy (V) to the small top along the small top beam (U), aligning the corners and stretching
it to fit.
Fig.13: Place the large canopy (W) to the roof; do not spread it. Attach the assembled small top to the big top
frame.
HH
Part NO. Description QTY CS NO. Image
Φ6x260 peg
GG Plastic ring 52 PCS
16 PCS P12405A01001
P90701A07007
Hardware Pack 3
Fig.7: Connect the corner bar connector (H1 & H2) to the top of post (A) with screw (AA) and washer (BB).
Fig.8: Insert the big top frame long beam (R) and the big top frame short beam (S) to the big top frame connector
(Q1 & Q2).
Fig.9: Insert the big top beam (L), short side beam (M) and long side beam (N) to assembled big top frame.

CARE AND MAINTENANCE:
1. This item is intended for decorative and sunshade purposes only, and is not designed to withstand severe
weather, including high winds, sustained tropical downpours, and snow. In order to avoid damage in such
instances, remove any accumulated water and the roof immediately. Disassemble the item in the reverse
order of the assembly steps if necessary prior to a severe storm.
2. A partially disassembled item is likely not stable enough to resist high winds and other severe weather, and
therefore can be damaged and/or cause damage. Complete disassembly is recommended prior to any major
storm.
3. Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
4. Steel components of garden accessories and furniture are treated with rust inhibiting paint. However, due to
the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural
process. To minimize this condition, it is recommended that care be taken when assembling and handling the
product, in order to prevent the paint from being scratched.
5. Surface rust can be removed easily using a very light application of common cooking oil. If surface
oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may start dripping onto the
assembly surface, which may cause damaging stains that may be difficult to remove.
6. If the product will not be used for a long period (e.g. winter time), it should be stored in a clean, dry
environment.
7. Keep the original packaging to store the item.
Made in China
Fig.14: Spread the large canopy (W) to the roof along the corner bar connector (H1 & H2), aligning the
corners and stretching it to fit. Connect the velcro of valance together.
Fig.15: Hang the mosquito netting (Y) to the netting bar P (O) with the plastic ring (GG).
Fig.16: Lift the base cover (C), secure the assembled gazebo to lawn with peg (HH).