Sunny SF-1118 User manual

Deluxe Inversion Table
SF-1118
Take a few moments to familiarize yourself with the specific parts and hardware included with your
product. Make sure all the parts and hardware are included in the carton and examine them for any
damage that may have occurred in transport. Some parts may be pre-assembled and pre-installed.
Photo may differ from actual product 1
Owner’s Manual Version:1304

•Do not use this inversion table without
approval from your physician.
•Read all instructions carefully before
using.
•Leave adequate space to properly invert.
Tighten all bolts before using equipment.
•Do not let children use the inversion table
unsupervised.
2
•For your safety, we suggest someone stand
by your side while you use this table.
•This equipment is designed for indoor and
[e-mail].
WARNING
Home use only, not intended for commercial use.
•For Customer Service, please contact:

3
PARTS LIST
Parts Listing: SF-1118 Inversion Table
Part# Description QTY Check
1Bottom Tube 2
2Backrest Support Tube 1
3Body Height Adjustment Tube 1
4Foot Rest Plate 1
5Adjustable Leg Hold Tube 1
6Handlebar-RIGHT 1
7
8L Base-frame-REAR-LEFT
8R
9L
9R
10 Leg Tube-REAR
11 Connecting Bracket
12 Cross Bar
13 Foam leg Rollers
14 Incline Adjustment Bolt 13.8X88mm
15 Round Spring Insert
16 Spring
17 Plastic Spacer
18 Plastic Round End-cap
19 Flat Washer 16×8.5×1.5
20 Bolt-M8×55mm
21 Lock Nut M8
22 Bolt-M8×50mm
23 Bolt-M8×30mm
24 Square End Cap
25L Handlebar Grip-LEFT
25R Handlebar Grip-RIGHT
26 Ball Pin- 8×72.5mm
27
28 Hexagonal Bolt-M8×20mm
29 Bolt-M8×20mm
30 Oval End Caps-Foot Rest
31 Base Frame End Caps
32
33 Square End Cap-for Part3
34 Stopper
35 EVA Space Pad
36 Round End Caps
37 Leg Tube Adjustment Knob
38
39 Metal Bushing for Rear Leg Tube
40
41
42
43
44
45
46 Round End Cap-for handlebars
50
49
48
47 Backrest Pad
Handlebar-LEFT
Base-frame-REAR-RIGHT
Base-frame-FRONT-LEFT
Base-frame-FRONT-RIGHT
Bolt-M8×60mm
Hexagonal Bolt-M8×65mm
Height Adjustment Knob
Bolt-M8×45mm
Metal Support Plate 100X38X2.5mm
Bolt-M6×40mm
Washer- 18×6.5×1.5
Nut M6
Plastic Washer- 20×9.5×2.5
1
1
1
1
1
1
2
1
4
1
1
1
4
2
23
8
16
1
6
6
1
1
2
2
2
4
2
4
4
1
1
1
4
1
1
2
1
1
1
4
2
1
1
1
Head Pad
51
52 Wrench-#13/#17
Hex Wrench
1
1
1
Metal Bushing-5.5mm
Bolt-M8×40mm
1
1

4
EXPLODED VIEW

5
STEP 1 - Base Frame
Unpack Base frame from Carton.
Attach the Front Bottom Tube (1)
to the Front Baseframe (9) using
2-Bolts (32). Then insert end cap
(31) onto the Tube (1).
Note: While doing this step please
face the open side of the end cap
(31) upward.
Repeat for the rear bottom tube as
shown.
Attach the Cross Bar (12) to the
Front Base Frame (9) using
4 Bolts (20) and 2 Metal Support
Plate (41), 4 Flat Washers (19)
and 4-Nuts (21).
Unfold Base Frame- Front ( 9)
from Base Frame-Rear (8),
Insert Ball Pin (26) through right
side hole between the 2 frames.
Right
Left
! Warning
Front Rear
NOTE: TIGHTEN ALL BOLTS AT THIS TIME

6
STEP 2 - Handlebar Assembly
Attach the Handlebars (6) and (7) to the Base Frame Rear (8L and 8R)
using 4 Bolts (20), 4 Flat Washers (19), and 4 Nuts (21). Use Bolt (22)
and Flat Washer (19) to fix the Right Handlebar (6) to the Base frame
Rear (8R) .
Parts Needed
Note:
Handlebar
Right(6)
NOTE: TIGHTEN ALL BOLTS AT THIS TIME

7
STEP 3 - BackrestAssembly to Base Frame
Attach the completed Backrest Pad and Head PadAssembly to the
Base Frame Unit using 4 Bolts (29), 4 Flat Washers (19) and 4 Lock
Nuts (21).
Install Incline Adjustment Bolt (14) into Incline Position 20 Hole and
Tighten.
Right
Left
Front Back
Parts Needed
NOTE: TIGHTEN ALL BOLTS AT THIS TIME

8
STEP 4 - Body Height Adjustment Tube and Rollers
Pull outAdjustable Leg Hold Tube (5) and turn 90 degrees to make sure the
holes are on top, then position horizontally as shown. (Part (5) has spring
pre-assembled inside Tube which should not be removed.)
Install Leg Tube (10) through hole in Adjustment Tube (3) using Hexagonal
Bolt (40), Metal Bushing (39),Flat Washer (19) and Lock Nut (21).
Insert Leg Tube Adjustment Knob (37) into threaded hole in Adjustment
Tube (3) and screw it tightly after aligning the holes of part (5) with part (3).
Slide Foam Leg Rollers (13) over Leg Tube-Rear (10) and Leg Hold Tube
(5).
NOTE: TIGHTEN ALL BOLTS AT THIS TIME
Install Foot Rest Plate (4) intoAdjustment Tube (3) using Hexagonal Bolt (50),
Metal Bushing (49) Flat Washer (19) and Lock Nut (21).

9
STEP 5 - Final Assembly
Slide HeightAdjustment Tube (3) into Backrest Support Tube ( 2) and
lock into place using Height Adjustment Knob (38), then fully insert
the ball pin (26) .
Note: This product is designed to adjust from 5’1” to 6’6”
with a Maximum User Weight of 300 LBS.

Make Sure All Nuts, Bolts
and Screws are Completely
Tightened Before Use.
10
Final Assembly