Sunricher C94-3ZW User manual

RF RGBW Wall Mounted Controller 09.280U3.04174
Click to play / pause the 10 built-in
effects, Press and hold down to
speed up/down the running effects
Function introduction
Important: Read All Instructions Prior to Installation
Touch color wheel, touch to
select R/G/B color
Click to choose zone, Press
and hold down to turn Off/On
corresponding zone
Click to select Warm White,
Natural White and Cool White
mixed by RGB colors
Click to switch on/off
Red channel:Click to turn off/on
Press and hold down to increase/
decrease light intensity
Blue channel:Click to turn off/on
Press and hold down to increase/
decrease light intensity
Green channel:Click to turn off/on
Press and hold down to increase/
decrease light intensity
White channel:Click to turn off/on
Press and hold down to increase/
decrease light intensity
Press and hold down to
increase/decrease light
intensity
Back side
19.4 mm 43.58 mm
65.58 mm
DC Power input
V- V+
DC INPU T
RF Wall Panel
Controller
83.00 mm
Wiring diagram
12-24VDC
PSU
AC 100-240V
Output Signal RF signal
Power Supply 12-24VDC
Power consumption 20 mA
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 75x120x29.1mm
• Touch sensitive
• Glass interface(white & black)
• Compatible with all universal series RF receivers
• Control RGBW color
• Control 3 zones synchronously and separately
• Waterproof grade: Ip20
• Radio frequency: 916.5MHz
Product Data
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
V- V+
DC IN PUT
RF Wa ll P anel
Controller
DC Version
RF Wall Panel
Controller
AC Version
L NL N
AC INPU T
AC Power input
RF signal
100-240VAC
20 mA
0-40°C
8% to 80%
75x120x29.1mm
DC Version AC Version
DC Version
AC 100-240V
AC Version
RF Wa ll P anel
Controller
AC Version
L NL N
AC IN PUT
AC Power
50/60Hz
AC Power
50/60Hz
Beulux Code: C94-3ZW

Installation
Pair with RF receiver(Method 1)
Step 2:Choose and click a zone number(e.g. zone 3)
Step 1:Click the “Learning Key” button on RF receiver or re-power on the
receiver three times continuously to set it into pairing status
Learning Key
RF LED Receiver
Step 3:Touch the color wheel, LED lights connected with the RF receiver
flicker once means the receiver is paired with zone 3 successfully.
Pair with RF receiver(Method 2)
Step 2:Choose and click a zone number(e.g. zone 3) three times, then press
and hold it continuously and quickly within 10 seconds, LED lights connected
with the RF receiver flicker once means the receiver is paired with zone 3
successfully.
Step 1:Power off and power on the receiver
Learning Key
RF LED Receiver
Built-in 10 color changing modes are as follows:
Mode 1: Any two colors of RGB mix fade-in & fade-out
Mode 2: RGB three colors mix fade-in & fade-out
Mode 3: RGB three colors mix fade-out & fade-in
Mode 4: RGB flash
Mode 5: RGB three colors fade-in & fade-out successively
Mode 6: RGB three colors fade-in successively
Mode 7: RGB three colors fade-out successively
Mode 8: RGB three colors jump changing successively
Mode 9: R&B two colors mix fade (R in B out), then G fade-in, then R&B mix fade (R out B in), then G fade-out
Mode 10: B fade-out, then G&B mix fade (G out B in), then R&G mix fade (R out G in), then R fade-in
1. Do wiring the wall panel & RF receiver according to wiring diagram (please refer to the instruction of RF receiver that
you would like to pair with)
2. Power on, then touch the button to turn on the controller, indicator of the controller turned blue
Operation
How to stop running mode of single color LED light caused by RGBW sender interference:
1. When pairing single color LED light to a single color remote, it might be interfered and paired by nearby
RGBW senders, which might control the single color light into running mode. The running mode can not be
stopped by the paired single color remote or by delete pairing.
2. Then we need this remote, and pair the remote to the receiver via above “Pair with RF receiver(Method 2)”,
then touch the color wheel to stop the running mode.
3. Then delete pairing and pair the receiver to the single color remote again, it can be controlled by the remote
again.