Sunricher SR-2834DMX-5C User manual

RF + DMX512 RGB+Dual Color Controller 09.2845C.04717
Function introduction
Important: Read All Instructions Prior to Installation
Back side
Product Data
Wiring diagram
60.3 mm
DMX512 Wall
Panel Controller
DC Power input DMX512 signal output
V- V+ D+ GNDD-
DMX OUT PUT
52.0 mm
60.3 mm 52.0 mm
19.4 mm
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
Output Signal DMX512 signal
Power Supply 12-24VDC
Power consumption 20 mA
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 86x86x29.1mm
• Touch sensitive
• Glass interface(white & black)
• Standard DMX512 Signal output
• Control RGB+CCT color
• Control 1 zone/area
• Waterproof grade: IP20
DMX512 Wall
Panel Controlle r
V- V+ D+ GN DD-
DMX O UTPUT
12-24VDC
PSU
AC 100-240V
RGB slider, slide touch to select R/G/B color
Dual color slider, slide touch to
adjust color temperature between
Warm White and Cool White
Click to turn on/off
Press and hold down to
increase/decrease light
intensity of RGB channels
Press and hold down to
increase/decrease light
intensity of dual color
channels
Click to play / pause the
RGB 10 built-in effects
Front side
V- V+
12V/24V
CV PSU
L
N
G
V-
V+
OUTPUT
INPUT
RGBW LE D Strip
G- G-
R- R-
V+ V+
B- B-
CCT Col or LE D Strip
CW- CW-
WW- WW-
V+ V+
RGB LED S tri p
DMX512 & RDM Decod er
Pin 1:Dat a+
Pin 2:Dat a-
Pin 7:GND
Pin 8:GND
12345678
DMX
Fem ale
Sig nal DMX S ignal
Mal e
DMX S ignal
RJ4 5
3
2
GND
GND
V+
V+
1/R -
2/G -
3/B -
4/W 1-
5/W 2-
Bac k Ente r Up Do wn
D+
D-
D+
D-
GND
1
3
21
12345678
Pin 1:GND
Pin 2:D-
Pin 3:D+
Pin 1:GND
Pin 2:D-
Pin 3:D+
DMX i n/out
DC Po wer
inp ut
DMX i n/outDMX i n/out
RGB LED S trip
V+ V+
R- R-
G- G-
B- B-
CCT LED S trip
V+ V+
WW- WW-
CW- CW-
DMX51 2 & RDM Dec oder
D -2
DMX S IGNAL
D +2
D -1
D1+
5/A -
4/W -
3/B -
2/G -
1/R -
+
V+
V+
V-
V-
12- 36VD C
POW ER INPU T
LED O UTPUT
Bac k Ente r Up Dow n
GND
V- V+
12V/24V
CV PSU
/36V
L
N
G
V-
V+
OUTPUT
INPUT

Installation
12-24VDC
Power Supply
Set DMX Address
This DMX master controller can control many DMX decoders, please set all decoders' address as 001.
Note: one DMX decoder has 5 channels, so it occupies 5 DMX addresses 001, 002, 003, 004, 005.
Pair with RF receivers:
Turn on the wall
panel controller
Click “Learning Key”
on RF receiver
LED lights connected with the
RF receiver will flicker once
The receiver is paired with
the remote successfully.
Touch color slider
on RF remote
How to delete the pairing:
Press and hold down “Learning Key” on the receiver for over 3 seconds until connected LED lights flicker twice,
which means the pairing is deleted successfully.