Sunricher SR-ZV9080A-B User manual

Z-Wave Curtain Motor Controller SR-ZV9080A-B
Safety & Warnings
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Quick Start
How to install:
• Step 1: power on the Z-Wave curtain motor controller.
• Step 2: activate inclusion mode on your Z-Wave controller.
• Step 3: activate inclusion mode of the curtain motor controller by triple press the network
inclusion/exclusion button. The curtain motor controller will be included to Z-Wave network.
Product Description
The curtain motor controller is a universal, Z-Wave Plus compatible, electric motor controller. The device
allows for controlling motors of roller blinds and venetian blinds, which are single phase AC powered. The
curtain motor controller allows for precise positioning of a roller blind or venetian blind slats. Precise
positioning is available for the motors equipped with mechanic and electronic end switches. The device
also allows for controlling on/off of lights. The module may be controlled wirelessly, through the Z-Wave
network primary controller, or through the switch keys connected to it. In addition, the curtain motor
controller is equipped with Power Metering and over current protection.
The curtain motor controller can be included and operated in any Z-Wave network with other Z-Wave
certified devices from other manufacturers and/or other applications. All non-battery operated nodes
within the network will act as repeaters regardless of vendor to increase reliability of the network.
Calibration button
AC power input
Network inclusion/
exclusion button
Load output
Switch input
Function Introduction
Ratings:120V~,60Hz,MAX:4A( )
FCC ID:XXXSR9080A
K1
K2
L
Q1 NN
AC 100-240V
S2
Curtain Motor
SR-ZV9080A-B(908.42MHz)
Made in China
S1
Q2
Controller
MAX:2A ( )
/
1

Z-Wave Frequency
Input Voltage
Output Voltage
908.42 MHz (US)
AC100-240V
AC100-240V
Resistive loads:4A
Capacitive/inductive loads:2A
0 to 40°C
8% to 80%
45.5x45x20.3mm
Product Data
Max. Load Current
Operating temperature
Relative humidity
Dimensions
The encryption mode that the curtain motor controller supports is S2 Unauthenticated. When the curtain
motor controller is being included into a Z-Wave network, you can use your primary controller/gateway to
enable encryption mode or disable encryption. (The primary controller/gateway shall support encryption
mode configuration). The curtain motor controller supports OTA and can update firmware wirelessly.
Main Features:
• Compatible with any Z-Wave or Z-Wave+ Controller,
• Controlled by Sunricher EasyHome or any other Z-Wave controller,
• Advanced microprocessor control
• Active element: electromagnetic, micro-gap relay switch
• The device may be operated by momentary or toggle switches, and by dedicated roller blind control
switches
• Connected motor's current and historical power consumption measured
• Over current protection
• To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of
applicable regulations
• The curtain motor controller supports OTA and can update firmware wirelessly
Installation Guide
Please read carefully the enclosed user manual before installation of the curtain motor controller, in order
to ensure an error-free functioning.
ATTENTION: Prior to the assembly of the product, the voltage network has to be switched OFF and
ensured against re-switching.
Inclusion (adding to a Z-Wave network)
1. Set primary controller/gateway into inclusion mode (Please refer to your primary controller’s manual on
how to turn your controller into inclusion).
2. Power on the curtain motor controller and set it into inclusion mode. There are two methods to set the
curtain motor controller into inclusion mode:
1)Triple press the network inclusion/exclusion button, it will set the curtain motor controller into inclusion
2

3
mode
2)When the value of configuration parameter 8 is set as 1, triple press the switch connected to S1, it will
set the curtain motor controller into inclusion mode. 6 seconds timeout if there is no reply from the Z-Wave
primary controller, repeat the operation.
3. The curtain motor controller will be added to the Z-Wave network.
Exclusion (removing from a Z-Wave network)
1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers
manual on how to set your controller into exclusion).
2. Power on the curtain motor controller and set it into exclusion mode. There are two methods to set the
curtain motor controller into exclusion mode:
1)Triple press the network inclusion/exclusion button, it will set the curtain motor controller into exclusion
mode. 6 seconds timeout if there is no reply from the Z-Wave primary controller, repeat the operation.
2)When the value of configuration parameter 8 is set as 1, triple press the switch connected to S1, it will
set the curtain motor controller into exclusion mode. 6 seconds timeout if there is no reply from the Z-
Wave primary controller, repeat the operation.
3. The curtain motor controller will be removed from the Z-Wave network.
Factory Reset
Press and hold down network inclusion/exclusion button for over 10 seconds, the curtain motor controller
will be reset to factory defaults.
Configure Parameter 3 to Set Working Mode
1. When parameter 3 value is configured as 0, light mode: either S1 or S2 can control both Q1 and Q2,
short pressing or holding down will be recognized automatically. For detailed configuration please refer to
configuration parameter 7.
Note: when configured as light mode, endpoint 1 reflects to relay 1 (Q1), endpoint 2 reflects to relay 2
(Q2).
2. When parameter 3 value is configured as 1, shutter mode without positioning: S1 and S2 are only valid
while held down. Hold down S1, relay 1 (Q1) ON, relay 2 (Q2) OFF. Hold down S2, relay 2 (Q2) ON, relay 1
(Q1) OFF.
3. When parameter 3 value is configured as 2, shutter mode with positioning: S1 and S2 are only valid
while held down. Hold down S1, relay 1 (Q1) ON, relay 2 (Q2) OFF. Hold down S2, relay 2 (Q2) ON, relay 1
(Q1) OFF. When reaching any end’s positioning, both relays will be OFF.
4. When parameter 3 value is configured as 3, venetian mode (up/down and slats rotation): Hold down S1,
relay 1 (Q1) ON, relay 2 (Q2) OFF. Hold down S2, relay 2 (Q2) ON, relay 1 (Q1) OFF. When reaching any
end’s positioning, both relays will be OFF. This mode supports shutter dim command, which means it
supports the secondary switch of command class SWITCH_MULTILEVEL_START_LEVEL_CHANGE.
Positioning Calibration
Calibration is a process during which a curtain motor controller learns the position of the limit switches
and a motor characteristic. Calibration is mandatory when the working mode of the curtain motor
controller is Shutter mode with positioning and venetian mode (up/down and slat rotation).Connect the
controller to the motor according to wiring diagram, there are two calibration methods as follows:
. 6 seconds timeout if there is no reply from the Z-Wave primary controller, repeat the operation.

4
Association Groups:
Association
Groups Description
1. When press and hold down “K2” button for 10S to reset the
device, send "Device Reset Locally Notification" to associated
devices of this group to report factory reset information.
2. When over load detected, send "NOTIFICATION_REPORT" to
associated devices of this group.
Group 1
Group
Name
Lifeline
Max
Nodes
5
1. Calibration through the calibration button, short press the button twice, calibration starts automatically.
2. Set the configuration parameter 6 value to 1, calibration starts automatically.
Secene Control
Users can configure scenes using command class SCENE_ACTUATOR_CONF_SET, and activate the
scenes using command class SCENE_ACTIVATION_SET.
Activate Scenes Using Switch S1 S2
Users can configure configuration parameter 9 to decide whether to send scene activation command
using command class CENTRAL_SCENE_NOTIFICATION.
The scene ID and key attribute supported by switch S1 and S2 are as follows:
Default configuration of CENTRAL_SCENE_CONFIGURATION_SET is Slow Refresh = 1(send Key Held
Down every 55s when the switch is pressed and held down).
Association
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another
device is called association. In order to control a different device, the controlling device needs to maintain
a list of devices that will receive controlling commands. These lists are called association groups and they
are always related to certain events (e.g. button pressed). In case the event happens all devices stored in
the respective association group will receive a common wireless command.
Switch Number
S1
S2
Support Action type Scene ID Key Attribute
Short press once
Short press twice
Short press 3 times
Press and hold, release
1
1
1
1
2
2
2
2
Key pressed once
Key pressed twice
Key pressed 3 times
Key held down and released
Short press once
Short press twice
Short press 3 times
Press and hold, release
Key pressed once
Key pressed twice
Key pressed 3 times
Key held down and released

5
Set and unset associations:
(Note: All association information will be cleared automatically once the curtain motor controller is
excluded from a network.)
Set association by operating primary controller/gateway to send packets to the curtain motor controller:
The primary controller/gateway sends packets to the curtain motor controller using
"COMMAND_CLASS_ASSOCIATION" or "COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION".
Node Information Frame
The Node Information Frame is the business card of a Z-Wave device. It contains information about the
device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by
sending out a Node Information Frame. Beside this it may be needed for certain network operations to
send out a Node Information Frame.
How to send out Node Information Frame:
When the curtain motor controller is set to inclusion/exclusion mode again, it will send out Node
Information Frame, there are 2 kinds of operation as follows:
1. triple press the K2 button, the curtain motor controller will be set to inclusion/exclusion mode, then send
out Node Information Frame.
2. When the curtain motor controller is under inclusion mode, there are two kinds of operation:
1) Triple press K2 button, the curtain motor controller will be set to inclusion mode again, and send out
Node Information Frame.
2) Power off and power on the curtain motor controller, it will be set to inclusion mode automatically, and
send out Node Information Frame.
Technical Data
Group 3 5
REP EP2
When endpoint 1 state changes, send
"SWITCH_MULTILEVEL_REPORT" to associated devices of this
group.
Group 2 REP EP1 5
When endpoint 2 state changes, send
"SWITCH_BINARY_REPORT" to associated devices of this group.
3. Report energy meter actively.
4. When action of S1 and S2 is detected, send
CENTRAL_SCENE_NOTIFICATION_V3
this group.
to associated devices of

6
COMMAND_CLASS_POWERLEVEL V1 YES
COMMAND_CLASS_CONFIGURATION V1 YES
COMMAND_CLASS_FIRMWARE_UPDATE_MD V4 YES
COMMAND_CLASS_NOTIFICATION V8 YES
COMMAND_CLASS_METER V3 YES
Wireless Range
SDK
Explorer Frame Support
Device Type
Generic Device Class
Specific Device Class
Role Type
up to 100 m outside, on average up to 40 m inside buildings
6.71.03
Yes
Window Covering Position/Endpoint Aware
GENERIC_TYPE_SWITCH_MULTILEVEL
SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL
Always On Slave (AOS)
SUPPORTED COMMAND CLASS
Node Info
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_TRANSPORT_SERVICE
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SECURITY
V2
V2
V1
V1
Endpoint 1 device type ：
GENERIC_TYPE_SWITCH_MULTILEVEL/SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL
Endpoint 2 device type:
GENERIC_TYPE_SWITCH_BINARY/SPECIFIC_TYPE_POWER_SWITCH_BINARY
Root Device Command List
Support S2/S0
COMMAND_CLASS_SUPERVISION V1
COMMAND_CLASS_SWITCH_BINARY V1 YES
COMMAND_CLASS_SWITCH_MULTILEVEL V3 YES
COMMAND_CLASS_ASSOCIATION V2 YES
COMMAND_CLASS_ASSOCIATION_GRP_INFO V1 YES
COMMAND_CLASS_VERSION V2 YES
COMMAND_CLASS_MANUFACTURER_SPECIFIC V2 YES
COMMAND_CLASS_DEVICE_RESET_LOCALLY V1 YES

Node Info
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SECURITY
V2
V1
V1
Endpoint 1 Command List
Support S2/S0
COMMAND_CLASS_SUPERVISION V1
COMMAND_CLASS_SWITCH_BINARY V1 YES
COMMAND_CLASS_SWITCH_MULTILEVEL V3 YES
COMMAND_CLASS_ASSOCIATION V2 YES
COMMAND_CLASS_ASSOCIATION_GRP_INFO V1 YES
Node Info
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SECURITY
V2
V1
V1
Endpoint 2 Command List
Support S2/S0
COMMAND_CLASS_SUPERVISION V1
COMMAND_CLASS_SWITCH_BINARY V1 YES
COMMAND_CLASS_ASSOCIATION V2 YES
COMMAND_CLASS_ASSOCIATION_GRP_INFO V1 YES
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION V3 YES
COMMAND_CLASS_SCENE_ACTIVATION V1 YES
COMMAND_CLASS_SCENE_ACTUATOR_CONF V1 YES
COMMAND_CLASS_SCENE_ACTIVATION V1 YES
COMMAND_CLASS_SCENE_ACTUATOR_CONF V1 YES
COMMAND_CLASS_MULTI_CHANNEL V4 YES
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION V3 YES
COMMAND_CLASS_SCENE_ACTIVATION V1 YES
COMMAND_CLASS_SCENE_ACTUATOR_CONF V1 YES
COMMAND_CLASS_CENTRAL_SCENE V3 YES
7
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION V3 YES

8
Enable/disable to save positioning
percentage, record and save current
positioning every time when the curtain moves
to specified position, if the working mode is
configured as light mode, record on/off state.
0x00: disable
0x01: enable
0x04(4) 1 1
Working mode
0: light mode
1: Shutter mode without positioning
2: Shutter mode with positioning
3: venetian mode (up/down and slats rotation)
0x03(3) 1 2
Configuration Command Class
Size Description(decimal numeral ) Default Value
Parameter
Enable/disable the curtain motor controller to
report state change percentage threshold
(report only when change value at the
specified percentage), if enabled, report when
the value reaches both 0% and 99%. When the
working mode is configured as light mode, as
long as the state changes, the state change
percentage threshold will be reported.
SWITCH_MULTILEVEL_REPORT
0: disable to report actively
1-10: value to report, unit is one percent
0x02(2) 1 1
Enable/disable over current protection
0: disable
1: enable, when over current detected, there
are two methods to cancel alarm:
1. short press either switch button S1 or S2,
the alarm will last at least 1 minute and then be
cancelled.
2. re-power on the curtain motor controller
0x05(5) 1 1
Notification Type
NOTIFICATION_TYPE_POWER_MA
NAGEMENT(08)
Triggerring Event
POWER_MANAGEMENT_OVERCURRENT_DETE
CTED(06)
Notification Report
Over Current Alarm When connecting to resistive load over current value is 4 1A When
connecting to a motor or capacitive load, over current value is 2.1A. Over current relays will be
closed.
: , . .

9
When parameter 3 value configured as 0 (light
mode), configuration of button S1 and S2
control.
Value=0
Short press S1 to switch ON/OFF Q1. Press and
hold down S1 to switch ON Q1, then release to
switch OFF Q2.
Short press S2 to switch ON/OFF Q2. Press and
hold down S2 to switch ON Q2, then release to
switch OFF Q2.
Value=1
Short press S1 to switch ON/OFF Q1. When S1
is pressed and held down, then released, not
processed.
Short press S2 to switch ON/OFF Q2. When S2
pressed and held down, then released, not
processed.
Value=2
Press and hold down S1 to switch ON Q1, then
release to switch OFF Q2. When S1 short
pressed, not processed.
Press and hold down S2 to switch ON Q2, then
release to switch OFF Q2. When S2 short
pressed, not processed.
Value=3
Short press S1 or S2 to switch ON/OFF of both
Q1 and Q2 simultaneously. When S1 or S2
pressed and held down, not processed
Value=4
Press and hold down S1 to switch ON Q1 and
Q2. When S1 short pressed, not processed.
Press and hold down S2 to switch OFF Q1 and
Q2. When S2 short pressed, not processed.
0x07(7) 1 0
Only value 1 can be written in, which means
starting positioning calibration.
When read,
0x01: positioning calibration completed
0x00: positioning not calibrated
This parameter is only valid when parameter 3
configured as shutter mode with positioning or
venetian mode (up/down and slats rotation).
0x06(6) 1 0

10
1 0
0x0A(10) 1 10
Enable/disable to add the device to or remove
it from a Z-Wave network through button S1.
Please refer to the parts of inclusion and
exclusion for details.
0: enable
1: disable
0x08(8) 1 1
1 0
Power change absolute threshold report, unit is W
0: disable absolute threshold report function
1-100: value of the power change absolute
threshold, if power change value is over the
threshold value, report the power change value
using METER_REPORT
Current change absolute threshold, unit is 0.1A
0: disable absolute threshold function
1-10: value of the current change absolute
threshold, if current change value is over the
threshold value, report the current change value
using METER_REPORT
0x0B(11)
0x0C(12)
Voltage change absolute threshold, unit is 1V
0: disable absolute threshold function
1-10: value of the voltage change absolute
threshold, if voltage change value is over the
threshold value, report the voltage change value
using METER_REPORT
Enable/disable to send scene activation
command
CENTRAL_SCENE_NOTIFICATION_V3 when
the switches S1 and S2 are pressed.
0: disable to send for action of both S1 and S2
1: enable to send for action of both S1 and S2
2: enable to send for action of only S1
3: enable to send for action of only S2
0x09(9) 1 1

11
Wiring Diagram
Notes for the diagrams:
L - terminal for live lead
N - terminal for neutral lead
S1 - terminal for switch key No. 1 (enable to set the device into inclusion/exclusion mode)
S2 - terminal for switch key No. 2
Q1 - output terminal no. 1 for electrical motor
Q2 - output terminal no. 2 for electrical motor
K1 - positioning calibration button when working mode is configured as shutter mode with
positioning or venetian mode (up/down and slats rotation)
K2 - inclusion/exclusion button (used to add or remove a device from the system)
Compatible Load Types
Supported load types 100-240V~
Lamp and resistive loads
Inductive loads
Max. 4A
Max. 2A
Capacitive loads Max. 2A
1 15 (1.5S)0x0d(13)
Slats rotation time, unit is 0.1S
0: disable the function
5-250 (0.5S-25S): value of the slats rotation time
This parameter is only valid when parameter 3 is
configured as venetian mode (up/down and slats
rotation).
4 3600 (1 hour)0x0E(14)
Time cycle to report the values of energy
consumption, voltage, current and load power
actively
60-2678400 (31 days), value of the time cycle,
unit is S.

(2) Light Mode Connection Diagram
Neutral
Live
Ratings:120V~,60Hz,MAX:4A( )
FCC ID:XXXSR9080A
K1
K2
L
Q1 NN
AC 100-240V
S2
Curtain Motor
SR-ZV9080A-B(908.42MHz)
Made in China
S1
Q2
Controller
MAX:2A ( )
/
S2 S1
(1) Curtain Motor Connection Diagram
DOWN
UP
Neutral
Live
Ratings:120V~,60Hz,MAX:4A( )
FCC ID:XXXSR9080A
K1
K2
L
Q1 NN
AC 100-240V
S2
Curtain Motor
SR-ZV9080A-B(908.42MHz)
Made in China
S1
Q2
Controller
MAX:2A ( )
/
S2 S1
12