SunSetter Vista Series User manual
RETRACTABLE AWNINGS
For Technical Support visit us at hp://ownerscorner.sunseer.com
or Call Toll Free 800-670-7071 • Fax 877-224-4944
©SunSeer Products, a Massachuses Limited Partnership, 184 Charles Street, Malden, MA 02148
Note
1. Locate the supplied Fasteners and Screws used
2.
See .
:
• Long Phillips Screws 12 16 20
• Short Phillips Screws 12 16 20
• 12 16 20
• 6 8 10
• 6 8 10
• 6 8 10
• 6 8 10
• 111
1st Fastener
#6 Philips head screws
(2 Places)
Fasteners
HOUSE
Fastener
:
• Measuring tape,
• pencil,
• step ladder,
•
•
•
:
•
2
2.
3.
Note
3.
.
4.
See .
:
7.
and against the wall (see
8.
9.
Note
1.
against the wall. See .
HOUSE
(See Figure 3)
Valance
©SunSeer Products, 184 Charles Street, Malden, MA 02148
For Technical Support visit us at hp://ownerscorner.sunseer.com
or Call Toll Free 800-670-7071 • Fax 877-224-4944
Instructions for Use of Breakaway Safety Clips for Awning Cover
* REQUIRED *
Parts Supplied:Safety Clip, Cord Lock, Gear, and Cord. (Safety Clip Kit)
See Figure 1 for parts idencaon and table below for number of parts.
Assembly of Breakaway Safety Clips
1. Thread a Cord through one of the Safety Clip handles. See Figure 2.
2. Slide the two ends of the Cord through the Cord Lock from the
smaller (flat edge) side to the larger (curved) side. (Do not pull the
entire Cord through.) See Figure 3.
3. Hold the Cord Lock in the center of the Cord and separate the two
ends of the Cord. See Figure 4.
4. Slide the Gear into the large (curved) side of the Cord Lock until the
Gear pops into place. Be sure that the part of the Gear that
protrudes is aligned with the slot in the Cord Lock. See Figure 5.
5. Repeat with remaining Safety Clips, Cords, Gears, and Cord Locks.
Figure 3
Cord through Cord Lock
Figure 4
Gear (White or Black)
Cord Lock
Ends of
Cord
Figure 5
Gear in
Cord Lock
Cord Lock
Safety Clip
Gear (White or Black)
Cord
Figure 1 - Parts Supplied (Safety Clip Kit)
Figure 2
Cord through Clip Handle
Awning Size (ft) 8 10 11 12 13 14 15 16 17 18 19 20
Number of
Safety Clip Kits 66668888 8 10 10 10
SUDDEN IMPACT HAZARD
•USE ONLY provided Breakaway Safety Clips to fasten the Protective Cover around the Awning.
•DO NOT USE other tie-downs in addition to or instead of the provided Breakaway Safety Clips.
•DO NOT insert tie-downs through grommet holes on the Protective Cover.
•NEVER place a ladder or stand in front and at the level of the Front Bar of the Awning.
Failure to follow these instructions can present risk of DEATH or SERIOUS INJURY from being struck by an
Awning suddenly opening while removing tie-downs.
WARNING
SunSeer Products, 184 Charles Street, Malden, MA 02148
July 29, 2019 INSMCV-CoverMotorized.pdf
Detaching Breakaway Safety Clips
1. Verify Awning is closed and unplugged.
2. Posion yourself under the Awning and detach each Safety Clip, one at a me.
3. Stow each Safety Clip for future use by looping the Cord around the Square Bar and aaching the Clip to
the Cord. DO NOT REMOVE Cord from the Square Bar.
4. Plug in the electrical cord to use the Awning.
Figure 10
knot
Figure 9
knot
Figure 7 Grommet
on Cover
Safety
Clip
Figure 8
Cord
Lock
Installation and First Use of Breakaway Safety Clips
Figure 6 Square Bar
Cord
Lock
Safety
Clip
SUDDEN IMPACT HAZARD
•USE ONLY provided Breakaway Safety Clips to fasten the Protective Cover around the Awning.
•DO NOT USE other tie-downs in addition to or instead of the provided Breakaway Safety Clips.
•DO NOT insert tie-downs through grommet holes on the Protective Cover.
•NEVER place a ladder or stand in front and at the level of the Front Bar of the Awning.
Failure to follow these instructions can present risk of DEATH or SERIOUS INJURY from being struck by an
Awning suddenly opening while removing tie-downs.
WARNING
1. Close the Awning and unplug it from the electric outlet.
2. Secure the Breakaway Safety Clips around the Awning Square Bar as follows:
a. Pass the Safety Clip over the top of and down the back side of the Square
Bar. See Figure 6.
b. Thread the Safety Clip through the loop in the Cord (between the Cord Lock
and Square Bar). See Figure 6.
c. Attach the Safety Clip to the bottom edge of the Cover along the hem by
each Grommet location. See Figure 7.
d. Cinch the Cord Lock towards the Square Bar until the Cover is snug. See
Figure 8.
3. After cinching to the desired snugness, create a knot using the two Cord ends,
so the knot is located approximately 1 inch from the Cord Lock. See Figure 9.
4. Trim the excess Cord close to the knot at each location. See Figure 10.
5. Call 800-670-7071 for Free replacement Cord Locks, if necessary.
Loop
Table of contents
Other SunSetter Accessories manuals
SunSetter
SunSetter VISTA Operating instructions
SunSetter
SunSetter Platinum Plus Series Original instructions
SunSetter
SunSetter VISTA Quick start guide
SunSetter
SunSetter Platinum Plus Guide
SunSetter
SunSetter PRO Operating and safety instructions
SunSetter
SunSetter VISTA Original instructions
SunSetter
SunSetter EASYSHADE Guide
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter Gaviota Quick start guide
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter EASYSHADE Original instructions
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter 900XT Installation guide
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter 900XT Use and care manual
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter Motorized Series Original instructions
