SunSetter Gaviota Quick start guide
For Technical Support visit us at hp://ownerscorner.sunseer.com,
e-mail contactus@sunseer.com, or Call Toll Free 800-670-7071 • Fax 877-224-4944
©SunSeer Products, 184 Charles Street, Malden, MA 02148
Tools Needed
Helpers Needed
Parts Supplied
Figure 3
Slot
Slot
Lower Screw Hole
Figure 1 HOUSE
Safety Sleeves
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!! PLEASE READ
THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE THIS PROCESS.
WARNING: FAILURE TO FULLY INSTALL THE SAFETY SLEEVES CAN RESULT IN PERSONAL INJURY!
Step 4
my
4. Slide the supplied Safety Sleeves onto both Lateral Arms
Figure 1
See Figure 2
Note
Front Bar End Plate
Figure 3
Figure 2
PLEASE NOTE THAT LEFT AND RIGHT REFERENCES ARE AS YOU FACE THE HOUSE.
2
ValanceFront Bar.
See Figure 3Valance SlotFront Bar.
Place the Valance
8. ,
Note: These Light Strips are snapped on to
Figures 4 & 5
Note
See Figure 5.
Figure 4
Figure 6
with the Lateral Arm
aached
Note: The Front Bar hangs by the rolled up Fabric.
Note: The replacement Arm Clamp and Lateral Arm
LEFT and RIGHT, on the Arm Clamp.
See Figure 8
WARNING: A HELPER MUST SUPPORT THE LATERAL
ARM WHILE IT IS BEING REMOVED. FAILURE TO DO
SO COULD CAUSE PERSONAL INJURY AND DAMAGE
TO THE PRODUCT.
Size Vinyl Fabric Acrylic Fabric XL
10’
non-motor end)
non-motor end)
N/A
11’
12’
13’
14’
15’
16’
17’
18’
19’ N/A
20’
Figure 7
Figure 7
Figure 8
Figure 4
Figure 5
See Note
at Step 11
cap
Figure 6
3
Slot
Figure 13
Figure 12
Figures 7 & 8
Figure 12
WARNING: A HELPER MUST SUPPORT THE LATERAL
ARM WHILE IT IS BEING INSTALLED. FAILURE TO DO
SO COULD CAUSE PERSONAL INJURY AND DAMAGE
TO THE PRODUCT.
Figure 10
Figure 14
Figure 10
Figure 10
See Figure 9.
Smaller, shorter
RIGHT side
only
Figure 11
Note: Insert the Allen Cap Bolt
from underneath the Lateral Arm.
opening on the top side of the
Lateral Arm. See Figure 10.
Note
Clamp and Lateral Arm Assembly
Figure 9
Steps 8 through 22
See Figure 12
Note: Both Lateral Arms, Arm Clamps, and Front Bar
WARNING: BEFORE REMOVING THE PLASTIC SAFETY
SLEEVES, MAKE SURE NO LADDER, PERSON OR
OBJECT IS IN FRONT OF THE AWNING. FAILURE TO
DO SO COULD RESULT IN PERSONAL INJURY.
WARNING: DO NOT CUT THE SAFETY SLEEVES.
FAILURE TO DO SO COULD RESULT IN PERSONAL
INJURY.
Note
remove
Tools Needed
2 ladders.
Figure 16
Slot
Figure 17
the closed Lateral
Arm.
Figure 18
WARNING: DO NOT
LOOSEN THIS BOTTOM
SET SCREW. DOING SO
CAN CAUSE THE ARM
TO SEPARATE FROM
THE ARM CLAMP,
WHICH COULD RESULT
IN PERSONAL INJURY.
Figure 15
helper and
ladder here
See Figure 15
Figure 15
See Figure 16
Figure 17
Note
beyond the Front Bar. This other Lateral Arm is
Connector.
WARNING: NO MORE THAN ONE
HALF TURN
Figure 16
Figure 18
Tools Needed:
Note
Figure 19 on Page 6
Figure 20 Page 6
49. Figure 20 Page 6.
Note
Note
To raise the Front Bar, complete steps 50 - 54:
WARNING: RAISING THE FRONT BAR WILL REDUCE THE PITCH (ANGLE) OF THE FABRIC THUS INCREASING THE RISK
OF RAINWATER POOLING ON THE FABRIC. TO PREVENT THE AWNING FROM COLLAPSING DUE TO RAINWATER LOAD,
YOU MUST RETRACT THE AWNING WHEN UNATTENDED. FAILURE TO DO SO COULD RESULT IN PERSONAL INJURY.
Figure 20 Page 6 to see
Step 60
Figure 20 Page 6 to
Note
Step 60
62. See Figure 20 Page 6.
Figure 19 Page 6
66. Note
Helper
Lateral Arm
Arm Clamp
(See Figure 20)
Front Bar
Figure 18
House
Figure 17
Bar
Arm
Clamp
Bar
at factory set height.
Arm
Clamp
top of the Fabric on the Roller Bar.
Arm
Clamp
Bar
Figure 20
Arm Clamp
Note
CAUTION
Figure 19
on Arm Clamp
7
the
Arm on the same side as the motor
Figure 21
Note
Note
Note: Reprogramming the Wireless Wind Sensor is not necessary, though it should be tested regularly. To
Facing UP
Front Bar
Figure 21
8
Figure 2
HOUSE
AB
C
DE
F
Note
in order of A, B, C, D, E, F
UNDERSIDEFigure 2
:
Figure 4
Figure 5
:
Figure 5
Figure 6
Note
Arms. See Figure 2.
Note
9
Figure 4
•
the Lateral Arms.
• Do NOT Drill into the side
of the Lateral Arms.
• Stop Drilling as soon as
the Drill Bit cuts through
Figure 5
Figure 6
Figure 2Step 3Note: Have your helper hold
WARNINGS:
• IN THE NEXT STEP, YOU MUST DRILL INTO THE LATERAL ARMS FROM UNDERNEATH, NOT FROM THE
SIDES. FAILURE TO DO SO CAN CAUSE DAMAGE TO THE LATERAL ARM.
• ALWAYS USE EYE PROTECTION WHEN OPERATING A DRILL.
• WHEN DRILLING, AS SOON AS THE DRILL BIT GOES THROUGH THE LATERAL ARM WALL, STOP
DRILLING. FAILURE TO STOP AS DESCRIBED CAN CAUSE DAMAGE TO THE LATERAL ARM AND THE
PROVIDED DRILL BIT.
providedcarefullyFigures 4, 5 6 Stop
SunSeer Products, a Massachuses Limited Partnership, 184 Charles Street, Malden, MA 02148
Figure 9
Step 8
Note
Figure 9.
Figure 8
Improperly
Figure 7
Properly
Side view
Lateral
See Figure 7PROPERLYFigure 8IMPROPERLY
CAUTION
improperly aligned Clips can permanently damage the Clips. See Figures 7 and 8.
Other SunSetter Accessories manuals
SunSetter
SunSetter VISTA Operating instructions
SunSetter
SunSetter Oasis Use and care manual
SunSetter
SunSetter EASYSHADE Guide
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter 900XT Use and care manual
SunSetter
SunSetter Platinum Plus Series Original instructions
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter PRO Operating and safety instructions
SunSetter
SunSetter 900XT Installation guide
SunSetter
SunSetter Wireless Wind Sensor User manual
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter Motorized Series Original instructions
SunSetter
SunSetter VISTA Original instructions
SunSetter
SunSetter Vista Series User manual
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter OASIS Series User manual
